ページ1に含まれる内容の要旨
Hydraulic
t ransmission
Jack
Operating Instructions & Parts Manual
Model number capacity
atd-7430 1000 lbs
Series a
(air actuated Model)
1000 lbs
atd-7431
Series a
Model Atd-7431
Model Atd-7430 Series A
Series A
U.S. Patent NO. 5,341,723
This is the safety alert symbol. It is used to alert you to potential personal injury hazards.
!
Obey all safety messages that follow this symbol to avoid possible injury or death.
! advertencia ! WARNING
• Leer, comprender, y seguir las instruccióne
ページ2に含まれる内容の要旨
SaFetY and GeneraL inFOrMatiOn Save these instructions. For your safety, read, understand, and follow the information provided with and on this jack before using. The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use. The owner and operator shall be aware that use and repair of this product may require special skills and knowledge. Instructions and safety information shall be conveyed in the operator's native
ページ3に含まれる内容の要旨
PreP aratiOn assembly (refer to Figure 1) Tools required: 1/2" box end wrench, 19mm wrench, 3/8" hex socket & torque wrench. 1. Three major parts should be included in the package: (a) Hydraulic unit Assembly; (b) Saddle Assembly; (c) 2 pieces of base half with hardware. 2. Attach either one of the two base halves to the base of the hydraulic unit, then secure using allen head bolts and washers provided. Apply the same procedure to the other base half. Use torque wrench to tighten to 30 lb.f
ページ4に含まれる内容の要旨
! WARNING • read, understand, and follow all printed material provided with and on this product before use. • do not exceed rated capacity. • Use only on hard, level surfaces. • adequately support the vehicle before starting repairs. • If loaded jack must be moved, make certain that load is secured by appropriate means, is stable, is in the lowest possible position, is moved over a smooth, hard level surface and that the lifting platform is level. • Use of this product is limited to removal,
ページ5に含まれる内容の要旨
Maintenance Important: Use only good grade hydraulic jack oil. Avoid mixing different types of fluid and NEVER use brake fluid, turbine oil, transmission fluid, motor oil or glycerin. Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load. Mobil DTE 13M or equivalent recommended. adding oil 1. With saddle fully lowered, set jack in its upright, level position. Remove oil filler screw. 2. Fill until oil is level with the oil filler screw
ページ6に含まれる内容の要旨
rePLaceMent P artS Available Parts: Please refer to the Parts drawing when ordering parts. Not all components of this kit are replace- ment items, but are illustrated as a convenient reference of location and position in the assembly sequence. When ordering parts, give Model number, serial number and description below. Call or write for current pricing: Atd Tools Inc. 160 Enterprise Drive, Wentzville, MO 63385 Tel:(636)327-9050 Fax:(636)327-9046 replacement Parts ill
ページ7に含まれる内容の要旨
replacement Parts List for Models atd-7430 Series a & atd-7431 Series a: Repair Kit Contents: Item Part No. Description Qty. Item Description Qty. 1 G360-20000-000 Leg Assembly 2 28 U-Cup, Ram 2 2 G360-90030-K04 Bolt Set (4 sets) 1 29 O-Ring 1 3 G360-90030-K02 Caster, 3" Dia. 2 30 O-Ring 3 4 G360-90030-K01 Caster w/ Brake 2 31 O-Ring 1 5 5105-08015-000 Socket Head Bolt 1 32 Back-up Washer 1 6 4200-03500-000 Tilt Screw Assy. 2 33 O-Ring 1 7 G360-40000-000 Saddle Head Assembly 1 34 O-Ring 1 8 A070
ページ8に含まれる内容の要旨
One Year LiMited W arrantY For a period of one (1) year from date of purchase, atd t ools inc. will repair or replace, at its option, without charge, any of its products which fails due to a defect in material or workmanship, or which fails to conform to any implied warranty not excluded hereby. Performance of any obligation under this warranty may be obtained by returning the warranted product, freight prepaid, to atd t ools inc. Warranty Service Department, 160 Enterprise Drive, Wentzv
