ページ1に含まれる内容の要旨
TitelSeite.fm Seite 1 Dienstag, 11. Juli 2006 4:46 16
HME 43-K
Instructions for use
ページ2に含まれる内容の要旨
TitelSeite.fm Seite 2 Dienstag, 11. Juli 2006 4:46 16
ページ3に含まれる内容の要旨
UB_INT.fm Seite 1 Dienstag, 11. Juli 2006 4:52 16 A B D C E F
ページ4に含まれる内容の要旨
UB_INT.fm Seite 2 Dienstag, 11. Juli 2006 4:52 16 G H I J K
ページ5に含まれる内容の要旨
The HME 43-K headset The HME 43-K is a closed pilot’s headset with a noise- compensating microphone, designed for use in jet aircraft. The HME 43-K features an ultra-lightweight design with excellent ergonomic properties, replaceable leatherette earpads and a double-sided, adjustable padded headband. The leatherette earpads are extremely comfortable. The HME 43-K headset has two separate connectors – one for the microphone and one for the headphones. The microphone can be worn on either the le
ページ6に含まれる内容の要旨
Safety instructions • Please read these instructions carefully and completely before using the headset. • Make these instructions easily accessible to all users at all times. Always include these instructions when passing the headset on to third parties. • Never repair or attempt to repair a defective headset yourself. Contact your local Sennheiser agent or the Sennheiser Service Department. • Protect the headset from humidity and dust. Intended use of the headset Intended use includes: • having
ページ7に含まれる内容の要旨
Putting the headset into operation Connecting the headset Connect the 1/4“ (6.35 mm) stereo jack plug (PJ 055) for the headphones and the PJ 068 jack plug (5.25 mm) for the microphone to the corresponding jack sockets of your intercom. Wearing the headset The letters refer to the diagrams on the cover page. B Adjust the length of the headband to fit your head size or shape. The earpads should exert a slight pressure on the ears. C Holding the headset with two hands, carefully bend the headband t
ページ8に含まれる内容の要旨
Adjusting the volume Adjust the volume directly on the intercom. ATTENTION! High volume! This headset is capable of producing high sound pressure levels. Higher volumes or longer durations can damage your hearing! Set the volume to a medium level. Make sure that you can hear critical sounds such as warning alarms. Adjusting the microphone sensitivity H The microphone sensitivity has been factory pre-set. If necessary, you can change the microphone sensitivity by turning a small screwdriver in
ページ9に含まれる内容の要旨
Care and maintenance Cleaning the headset Use a soft, slightly damp cloth to clean the headset from time to time. If necessary, the headset can be cleaned with soapy water (use a mild cleanser such as a detergent). ATTENTION! Water can damage the electronics of the unit! Water entering the housing of the headset can cause a short-circuit and damage the electronics. Only use a slightly damp cloth to clean the headset. Do not use any solvents or cleansing agents. Replacing the earpads For reason
ページ10に含まれる内容の要旨
Replacing the wind screen If the wind screen shows signs of wear such as tears or holes, replace the wind screen. J Pull the wind screen from the microphone. Gently slide- on the new wind screen and ensure that it fits securely over the microphone. Storage and transportation K Turn the microphone into the position shown on the diagram. Rotate the earcups by 90°. Use the supplied carrying bag for storage and transportation. If problems occur ... Problem Possible cause Possible solution You cannot
ページ11に含まれる内容の要旨
Accessories Cable clip Cat. No. 091551 Leatherette ear pads Cat. No. 091532 Foam ear pads Cat. No. 091529 Wind screen Cat. No. 091540 Carrying bag Cat. No. 517619 Specifications General data Model HME 43-K Connection cable single-sided round cable, length 1.85 m Connectors 1/4“ (6.35 mm) stereo jack plug (PJ 055) for headphones, wired mono PJ 068 jack plug (5.25 mm) for microphone Weight without cable approx. 95 g Storage temperature –55° C to +70° C Operating temperature –5° C to +45° C
ページ12に含まれる内容の要旨
Headphones Transducer principle dynamic Frequency response 200 Hz to 6,000 Hz Sound pressure level 89 dB SPL at 1 V/1 kHz Ear coupling supra-aural, closed THD < 1 % Contact pressure approx. 1.5 N Nominal impedance 300 Ω Size of earcups ∅ 51 mm Microphone Transducer principle pre-polarized condenser, noise compensating Frequency response 400 Hz to 4,500 Hz Output voltage 170 mV/Pa; adjustable from 40 to 500 mV/Pa Supply voltage 8 to 16 V DC Current consumption typ. 10 mA at 8 V 8
ページ13に含まれる内容の要旨
Manufacturer Declarations Warranty regulations The guarantee period for this Sennheiser product is 24 months from the date of purchase. Excluded are accessory items, rechargeable or disposable batteries that are delivered with the product; due to their characteristics these products have a shorter service life that is principally dependent on the individual frequency of use. The guarantee period starts from the date of original purchase. For this reason, we recommend that the sales receipt be r
ページ14に含まれる内容の要旨
CE Declaration of Conformity This equipment is in compliance with the essential requirements and other relevant provisions of Directive 89/336/EC. The declaration is available on the internet site at www.sennheiser.com. Before putting the device into operation, please observe the respective country-specific regulations! WEEE Declaration Your Sennheiser product was developed and manufactured with high-quality materials and components which can be recycled and/ or reused. This symbol indicates th
ページ15に含まれる内容の要旨
Sennheiser electronic GmbH & Co. KG 30900 Wedemark, Germany Phone +49 (5130) 600 0 Fax +49 (5130) 600 300 www.sennheiser.com Printed in China Publ. 06/06 515687/A01
