ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
BlueAnt InterPhone Features Automatic Volume Adjusting High/Low Volume Modes Voice Dial and Voice Answer Bluetooth Helmet Handsfree Rider to Passenger Intercom Bike to Bike Intercom All Weather Water Resistant Index Package Contents ................................................................................................. 2 Product Descriptions ............................................................................................ 2 Charging the Headset ..........
ページ3に含まれる内容の要旨
Package Contents Product Descriptions The BlueAnt InterPhone is a Bluetooth Headset designed for the motorcycle rider and passenger who wish to have clear and reliable wireless communications while riding. This headset is equipped with hi-tech features: Voice and Answer Reject, Auto-Volume Level Adjusting, Low/High Volume Modes and Rider to Passenger or Bike to Bike Intercom. Note: You must have two Interphone Headsets to use the Intercom feature. This headset
ページ4に含まれる内容の要旨
Charging the Headset Note: After opening the box please charge the InterPhone before using. 1. Connect the provided AC charger’s plug to the Charger Socket(5). 2. Plug the charger to 110-240v electricity socket and Turn On. 3. The LED will blink Red to Green while charging. 4. When the LED turns a Steady Green, charging is complete. Disconnect the charger 5. When the LED turns to a blinking red, the battery is low. Charge the unit as above. Note: A normal c
ページ5に含まれる内容の要旨
Installing the Clip Mount Important: There are 2 types of Headset Clips included in this package. Either can be used with full or open faced helmets, on either side of the helmet. - Headset Clip Mount with Fastening Clamp. (removable) - Headset Clip Mount with Adhesive. (fixed) Use the one which best suits your helmets design. Using the Headset Clip Mount with Fastening
ページ6に含まれる内容の要旨
Using the Headset Clip Mount with Adhesive 1. Before removing the protective strip from the double-sided adhesive, find the best location to place the Headset Clip Mount. 2. Clean the part of the helmet that the Headset Clip Mount with Adhesive will be attached to. Remove any dirt or grease. Do not use cleaners that may damage the helmet or that will leave an oily residue. Make sure the surface is dry before continuing. 3. Check again the positioning of the clip. Once it is mounted it w
ページ7に含まれる内容の要旨
3. Next, take the Ear Speaker(7) and attach it to the Velcro Pad. Run the Microphone Arm down along down to where your mouth will be. As the Microphone Arm is flexible, you can adjust it so it sits in the optimum position in front of your mouth. Some helmets have removable padding; if yours does, it is recommended to run the speaker and mic under the padding. 4. Taking care to match the pins up, connect the Headset Plug(9) to the Headset Socket(5). The plug can only be inserted
ページ8に含まれる内容の要旨
Basic Operations IMPORTANT: The BLUEANT INTERPHONE needs to be ‘paired’ with your Bluetooth mobile phone before you can use the following functions. (See Pairing to your Bluetooth Mobile Phone on page 3.) Make a Call: Dial the number using your phone as normal. Audio will automatically be on the headset. Note: With some phones like Siemens S55 and Panasonic X70, audio is always on the phone during an outgoing call. You will need to press MFB(1) to transfer the audio to your h
ページ9に含まれる内容の要旨
Reject a Call (For Handsfree Profile Phones only): nd To reject an incoming call just press the MFB(1) for 2 seconds (2 beep). Or, Assuming the InterPhone Voice Answer and Reject is activated, be silent for 10 seconds. The call will automatically be rejected. Note: See InterPhone Voice Dial and Reject Activation / Deactivation on page 10 Audio Transfer (For Handsfree Profile Phones only): During an ongoing call, audio transfer can be made. From BLUEANT INTERPHONE to
ページ10に含まれる内容の要旨
Special Features High Volume or Low Volume Mode Setting to high or low volume mode depends on user’s helmet design or structure. Some helmet types may require near or far positioning of the InterPhones Ear Speaker(7) from the user’s ear. Please try both modes to discover which mode is appropriate for your helmet. High Volume Mode Activation is advised if you position the Ear Speaker(7) far from your ear. This will enable you to still have a clear and audible audio. Procedure:
ページ11に含まれる内容の要旨
Voice Answer and Reject Mode • When activated, the user can accept a call by saying any word within 10 seconds. The user can also reject a call by being silent for 10 seconds. • When deactivated, apply normal answer and normal rejection of call. Activation: 1. From Off, press and hold simultaneously the Volume Up(3) & Volume down(4) buttons. 2. Keep both buttons pressed and then press the MFB(1) for 5 seconds. 3. Power On beep followed by a HIGH TONE can be heard. The Status In
ページ12に含まれる内容の要旨
Advanced Functions Driver to Passenger or Bike to Bike INTERCOM The BLUEANT INTERPHONE has motorcycle intercom system that allows driver to passenger conversations. This intercom features full-duplex communication so driver and passenger may enjoy simultaneous conversations just like on the telephone. To use this feature you must have two BlueAnt InterPhone Headsets Intercom Pairing Procedure: 1. Prepare two BLUEANT INTERPHONES. Note: Make sure to switch off the phones paire
ページ13に含まれる内容の要旨
down on one of the Interphones until you hear the second beep, then both units will resume intercom mode. 3. During intercom mode, the ring of the phone will not be transferred to the BLUEANT INTERPHONE automatically. (Tip: Switch on your phone’s vibrate option to notice an incoming call.) 4. On an incoming call, Press the MFB(1) for 1 second to transfer the call to your headset. Some phones may require 2 times press on MFB(1) in st order to answer an incoming phone call from intercom mod
ページ14に含まれる内容の要旨
Specifications Bluetooth Compliance: Bluetooth Version 1.2 Specifications Supported Bluetooth Profiles: Bluetooth Headset and Handsfree Profiles with Automatic Detection Operating Range: Up to 33ft (10m) for cell phones Up to 450ft (150m) for two Interphones Frequency: 2.4GHz Talk Time: Up to 10 hours Standby Time: Up to 700 hours Charging Time: 4 hours Battery type: Rechargeable Lithium Polymer 350mAh Special features: Full Duplex Full DSP Noise Cancellati
ページ15に含まれる内容の要旨
Help Phone/Device Software Please make sure you have the latest firmware upgrade for your Phone especially if you are using a PDA Phone. Go to the support section of the manufacturers’ website to check you have the latest version. Many new mobile phones, pda’s and computers phones require a Bluetooth patch to improve Bluetooth functionality from the original released version. Resetting Your Phone/Device Phones can become prone to software and memory issues which may cause Bluetooth
ページ16に含まれる内容の要旨
Disclaimers: This manual is published by BlueAnt. The information contained in this document is subject to change without notice. All rights reserved. The Bluetooth word, mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by BlueAnt is under license. Other trademarks and trade names are those of their respective owners. Warning: Prolonged use of a headset at high volumes may affect your hearing capacity. Using for extensive time periods may result in noise i
ページ17に含まれる内容の要旨
