ページ1に含まれる内容の要旨
User’s manual
TL7700
DECT 6.0
accessory cordless headset
ページ2に含まれる内容の要旨
Congratulations on your purchase of this AT&T product. Before using this AT&T product, please read the Important safety information section on pages 26-29 of this manual. Please thoroughly read this user’s manual for all the feature operations and troubleshooting information necessary to install and operate your new AT&T product. You can also visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Model number: TL7700 (Headset and headset
ページ3に含まれる内容の要旨
Parts checklist Check to make sure the headset package includes the following items. Save your sales receipt and original packaging in the event warranty service is necessary. User’s manual TL7700 DECT 6.0 accessory cordless headset User's manual Cordless headset Headset charger with medium-sized earbud attached Battery pack (battery with Headset charger 2 earbuds battery compartment power adapter cover attached) 2 over-the-ear hooks Over-the-head band Behind-the-neck band
ページ4に含まれる内容の要旨
User’s manual TL7700 DECT 6.0 accessory cordless headset Table of contents Getting started Appendix Quick reference guide - Troubleshooting ..........................19 headset ......................................... 1 Important safety Headset lights ........................... 1 information ................................26 Headset alert tones ................ 3 Safety information..................26 Quick reference guide - Especially about cordless headset charger .....................
ページ5に含まれる内容の要旨
Getting started Quick reference guide - headset (On/off button and light) Press to make, answer or end a call. Headset lights light status Red • On when the headset is charging in the headset charger. • Flashes every 10 seconds to indicate the battery is low when the headset is not in the headset charger. • Flashes three times to indicate the headset is powering off. Blue • On when a fully charged and registered headset is in the headset charger. • Flashes three times to indicate the hea
ページ6に含まれる内容の要旨
Getting started Quick reference guide - headset VOL+/VOL- Push the volume switch on the headset to the right or left to adjust the headset ringer volume while in idle mode or the listening volume while on a call. Earpiece MUTE/FLASH Battery pack Press to mute the Open to replace the microphone during a call. battery pack. Press and hold for two seconds to answer an incoming call when you receive a call waiting alert during a call. Press to mute the ringer in the earpiece when there
ページ7に含まれる内容の要旨
Getting started Quick reference guide - headset Headset alert tones One short beep • Headset key tone. One short beep • Muted headset microphone alert tone. every 30 seconds Two beeps • Error alert tone. • The ringer volume is at its lowest setting. • The listening volume is at its highest or lowest setting. • Any key is pressed while the headset is out of range Two low beeps • Call waiting alert tone. Two rapid beeps • Low battery warning. every 20 seconds Three rising beeps • A conference ca
ページ8に含まれる内容の要旨
Getting started Quick reference guide - headset charger Magnetic charging mount Place the headset here for charging. Power cord slot Place the power cord here Power jack 4
ページ9に含まれる内容の要旨
Getting started Installation You must install and See pages 6-7 charge the battery before for easy instructions. STOP! using the headset. For customer service or product information, visit our website at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268. Avoid placing the telephone base too close to: • Communication devices such as television sets, VCRs or other cordless telephones. • Excessive heat sources. • Noise sources such as a window with traffic out
ページ10に含まれる内容の要旨
Getting started Battery installation The battery is permanently attached to the battery compartment cover (known as the battery pack). Do not try to separate them from each other. After installing the battery pack, charge it for at least 15 minutes. You may be able to make and receive short calls. For optimal performance, charge the headset battery for at least three hours before use. When fully charged, the headset battery provides approximately 12 hours of talk time or 5 days of standby
ページ11に含まれる内容の要旨
Getting started Battery charging and connecting charger power After installing the battery, charge the headset by placing it in the magnetic charging mount as shown below. The light turns on when the headset is charging. 1. Plug the small end of the headset charger power adapter into the power jack at the bottom of the headset charger. Place the power cord in the power cord slot. Plug the headset charger power adapter into an electrical outlet not controlled by a wall switch. 2. Insert the
ページ12に含まれる内容の要旨
Getting started Add and register headsets You must register your new TL7700 headset with a compatible AT&T DECT 6.0 telephone before use (see page 9). The telephone base recognizes and counts a headset the same as a handset. Refer to your telephone user’s manual for the maximum number of handsets and headsets that you can register to the telephone. If you have the maximum number of handsets registered, you need to follow the deregistration information in your telephone user’s manual before
ページ13に含まれる内容の要旨
Getting started Add and register headsets Register a headset to an AT&T DECT cordless telephone base 1. Make sure the battery is properly installed in the headset (see page 6). The light on the headset flashes slowly in red and blue to indicate the headset is not registered. 2. Place the headset in the headset charger and allow it to charge for at least one hour before beginning registration. 3. Remove the headset from the charger. 4. On the telephone base of the cordless phone, press an
ページ14に含まれる内容の要旨
Getting started Replace a headset You may need to deregister your headsets if: • You have already registered the headset and now wish to register your headset to a different AT&T DECT telephone. -OR- • You have registered the maximum number of headsets and need to replace one of them. Y You must fir ou must first der st deregist egister all headset er all headsets, s, and then register each headset you wish to use again, one at a time. Please read carefully through all the instructions on thi
ページ15に含まれる内容の要旨
Getting started Headset attachments Earbud There are three sizes of earbuds provided. The medium-sized earbud is already attached to the headset. To remove the earbud from the headset earpiece: Hold both sides of the earbud. Twist and pull the earbud until it separates from the earpiece. To attach the earbud to the headset earpiece: 1. Choose an appropriate earbud. 2. Position the earbud on the earpiece as shown below. 3. Press the earbud down on the earpiece until it clicks into place. Move
ページ16に含まれる内容の要旨
Getting started Headset attachments Over-the-ear hook There are two sizes of ear hooks provided. You can choose the suitable ear hook to attach to the headset. To adjust the headset to wear on the left or right ear: • To wear on the left ear: 1. Make sure the ear hook ring is positioned as shown in Figure 1 before installation. 2. Attach the ear hook ring. See the next page for instructions. Figure 1 • To wear on the right ear: 1. Make sure the ear hook ring is positioned as shown in
ページ17に含まれる内容の要旨
Getting started Headset attachments To attach the ear hook to the headset: 1. Remove any headset attachment (earbud excluded) connected to the headset earpiece. 2. Insert the earpiece into the ear hook ring as shown in Figure 3. 3. Press the edge of the ear hook ring towards the earpiece until it clicks into place as shown in Figure 4. 4. Hook the headset onto the desired ear. Adjust the angle of the headset until the microphone is pointing towards your mouth as shown in Figure 5. Figure 3 F
ページ18に含まれる内容の要旨
Getting started Headset attachments To remove the ear hook from the headset: Hold the headset with one hand. Twist and pull the ear hook with your other hand until it separates from the earpiece. 14
ページ19に含まれる内容の要旨
Getting started Headset attachments Over-the-head band To attach the head band to the headset: 1. Remove any headset attachment (earbud excluded) currently connected to the headset. 2. Insert the earpiece into the head band ring as shown in Figure 6. 3. Push the earpiece towards the head band ring until it clicks into place as shown in Figure 7. 4. Adjust the head band to fit your head. Adjust and rotate the angle of the headset until the microphone is pointing towards your mouth as shown i
ページ20に含まれる内容の要旨
Getting started Headset attachments To remove the head band from the headset: Hold the headset with one hand and the head band ring with your other hand. Twist and pull the headset until it separates from the head band ring. 16
