National Instruments NI 5102の取扱説明書

デバイスNational Instruments NI 5102の取扱説明書

デバイス: National Instruments NI 5102
カテゴリ: グラフィック用タブレット
メーカー: National Instruments
サイズ: 0.1 MB
追加した日付: 10/8/2014
ページ数: 8
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスNational Instruments NI 5102の取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、National Instruments NI 5102に関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書National Instruments NI 5102をこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書National Instruments NI 5102のフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - National Instruments NI 5102の説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
National Instruments NI 5102 取扱説明書 - Online PDF
Advertisement
« Page 1 of 8 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書National Instruments NI 5102を全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書National Instruments NI 5102の内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨

USER GUIDE

CALIBRATING THE NI 5102 WITH
CALIBRATION EXECUTIVE
Contents
Introduction............................................................................................. 2
What Is Calibration? ........................................................................ 2
Why Should You Calibrate? ............................................................ 2
How Often Should You Calibrate?.................................................. 2
Equipment and Other Test Requirements ............

ページ2に含まれる内容の要旨

Introduction This document contains information and step-by-step instructions for loading and running the calibration procedure for the NI 5102 using Calibration Executive. What Is Calibration? Calibration consists of verifying the measurement accuracy of a device and correcting for any measurement error. Verification is measuring the performance of a device and comparing the results to the factory specifications of the device. National Instruments calibrates every 5102 device at the factory. Du

ページ3に含まれる内容の要旨

Equipment and Other Test Requirements This section describes the equipment, documentation, software, and test conditions needed for calibration. Test Equipment Tables 1 and 2 list specifications for equipment you can use to calibrate your NI 5102 with Calibration Executive. Recommended Equipment Table 1 lists the equipment that National Instruments recommends for this procedure. Table 1. Required Equipment Specifications for NI 5102 Calibration Required Recommended Parameter Equipment Equipment

ページ4に含まれる内容の要旨

Alternative Equipment Table 2 contains a list of alternative equipment you can use to calibrate your NI 5102 with Calibration Executive. Table 2. Alternative Equipment Specifications for NI 5102 Calibration Required Recommended Parameter Equipment Equipment Measured Necessary Specifications Vertical Offset 0 VDC ±0.1 mV Calibrator Fluke 5700 Vertical Gain DC ±40 mV to ±4.5 V, ±0.1% Calibrator into 1 MΩ AC Coupling sine wave 9–13 Hz ±100 ppm, 1.8 Vpp ±2%into1MΩ High-Speed Signal Tektronix SG503 B

ページ5に含まれる内容の要旨

Software Complete the following steps to install Calibration Executive: 1. Make sure that your computer and monitor are powered on and that you have installed Windows 2000/NT/Me/9x. 2. Close all open applications. 3. Insert the installation CD into the CD-ROM drive. 4. Choose the Run option from the Start menu on the desktop task bar. 5. In the command line box, typex:\setup.exe (wherex is the letter of the CD-ROM drive you are using), and click OK. 6. Follow the instructions that appear in the

ページ6に含まれる内容の要旨

Calibration Procedures This section explains how to set up and run the Calibration Executive procedure. Using the Wavetek 9500 in automated mode, the calibration procedure takes approximately ten minutes. In manual mode, the procedure takes approximately 30 minutes. Using the alternative instruments in automated mode, the calibration procedure takes approximately 20 minutes. In manual mode, the procedure takes approximately 40 minutes. Connecting Your Calibrator, DMM, and NI 5102 The calibration

ページ7に含まれる内容の要旨

Viewing the Calibration Report When the procedure is finished, complete the following steps to view the calibration report: 1. Click View»Reports. 2. Select View to launch your browser and view your report. The calibration report appears as an printable HTML file. You have completed calibrating your NI 5102 with Calibration Executive. Note If your NI 5102 device fails after calibration, return the device to National Instruments for repair or replacement. © National Instruments Corporation 7 Cali

ページ8に含まれる内容の要旨

Technical Support Resources NI Web Support National Instruments Web support is your first stop for help in solving installation, configuration, and application problems and questions. Online problem-solving and diagnostic resources include frequently asked questions, knowledge bases, product-specific troubleshooting wizards, manuals, drivers, software updates, and more. Web support is available through the Technical Support section ofni.com Worldwide Support National Instruments has offices loca


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 National Instruments NI PCI-5114 取扱説明書 グラフィック用タブレット 0
2 National Instruments NI 5102 取扱説明書 グラフィック用タブレット 2
3 National Instruments NI 5911 取扱説明書 グラフィック用タブレット 0
4 National Instruments NI PXI-562X 取扱説明書 グラフィック用タブレット 1
5 National Instruments PXI/PCI-5114 取扱説明書 グラフィック用タブレット 1
6 National Instruments NI PXI-5621 取扱説明書 グラフィック用タブレット 0
7 Sony S 取扱説明書 グラフィック用タブレット 7
8 Sony SGPT11 取扱説明書 グラフィック用タブレット 8
9 Agilent Technologies DC282 取扱説明書 グラフィック用タブレット 2
10 Agilent Technologies DP110 取扱説明書 グラフィック用タブレット 1
11 Agilent Technologies DC135 取扱説明書 グラフィック用タブレット 0
12 Agilent Technologies DC211 取扱説明書 グラフィック用タブレット 1
13 Agilent Technologies DC122 取扱説明書 グラフィック用タブレット 1
14 Agilent Technologies DP1400 取扱説明書 グラフィック用タブレット 2
15 Agilent Technologies DP106 取扱説明書 グラフィック用タブレット 1