ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
IMPORTANT NOTICES General • This manual has been authored with simplified grammar, to meet the needs of international users. • The operator of this equipment must read and follow the descriptions in this manual. Wrong operation or maintenance can cancel the warranty or cause injury. • Do not copy any part of this manual without written permission from FURUNO. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications can
ページ3に含まれる内容の要旨
SAFETY INSTRUCTIONS Read these safety instructions before you operate the equipment. Indicates a condition that can cause death or serious WARNING injury if not avoided. Indicates a condition that can cause minor or moderate CAUTION injury if not avoided. Warning, Caution Mandatory Action Prohibitive Action Safety Instructions for the Operator WARNING WARNING WARNING WARNING Immediately turn off the power at the Use the proper fuse. switchboard if water leaks into the equipment or somethin
ページ4に含まれる内容の要旨
SAFETY INSTRUCTIONS Safety Instructions for the Installer CAUTION CAUTION WARNING WARNING Observe the following compass safe Turn off the power at the switchboard distances to prevent interference to a before beginning the installation. magnetic compass: Fire or electrical shock can result if the power is left on. Standard Steering compass compass Do not install the equipment where it MU-150HD 0.65 m 0.45 m may get wet from rain or water splash. Water in the equipment can result in
ページ5に含まれる内容の要旨
TABLE OF CONTENTS Note: This manual contains both English and Japanese instructions. The Installation Materials, Outline Drawings, and Interconnection Diagram are located at the back of this manual. FOREWORD ....................................................................................................................v SYSTEM CONFIGURATION ..........................................................................................vi EQUIPMENT LISTS...........................................
ページ6に含まれる内容の要旨
FOREWORD A Word to the Owner of the MU-150HD FURUNO Electric Company thanks you for purchasing the MU-150HD 15” Marine Display. We are confident you will discover why the FURUNO name has become synonymous with quality and re- liability. For over 60 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment is designed and con
ページ7に含まれる内容の要旨
SYSTEM CONFIGURATION RGB MODEL1824C/1833C/1943C, FSV-30, FCV-30, FCV-1200L etc. DVI MFD8/MFD12/MFDBB, 2 ports FAR-21X7 series etc. VIDEO (NTSC/PAL) CCD camera, DVD recorder, etc. 3 ports Environmental category MARINE DISPLAY MU-150HD: Protected from the weather MU-150HD 12-24 VDC Connectable equipment Equipment Resolution Signal FCV-1200L/M VGA Analog RGB, via IF-8000 CH-250/S VGA Analog RGB, via IF-8000 CH-270 VGA Analog RGB, via IF-8000 CH-300 VGA Analog RGB, via IF-8000 CSH-5L/8L XGA Analog
ページ8に含まれる内容の要旨
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display Unit MU-150HD — 1 w/ Hard cover Installation CP26-01300 000-016-267 1 set • CP26-01302* Materials • Flush Mounting Plate Assy. (CP26-01301, Code: 001-080-760) 2 pcs. • Cable Assembly (MJ-A3SPF0017-050ZC, Code: 000-157-995-10) 1 pc. Accessories FP26-00401 001-080-780 1 set LCD Cleaning Cloth (02-155-1082-1, Code: 100-332-651-10) 1 pc. Spare Parts SP26-00201 001-080-750 1 set • Fuse (FGBO-A 125V 5A PBF, Code: 000- 155-853-10
ページ9に含まれる内容の要旨
1. MOUNTING, WIRING 1.1 Preparation Mounting type You can install the display unit as follows. See the outline drawing at the back of this manual for mounting dimensions. • Flush mounting, fixed at rear (standard) • Flush mounting, fixed at front (option) • Flush mounting, fixed at rear, with hood (option) • Desktop mounting (option) • Flush mounting a series side by side, fixed at rear Note: The face of the LCD monitor is made of glass. Handle it with care. Mounting location When you choose a
ページ10に含まれる内容の要旨
1. MOUNTING, WIRING The upper edge of the hard cover Pull forward the upper edge by pressing here with thumbs. How to remove the hard cover To attach the hard cover, follow the illustration in the figure below. Cutout Tab Set the tabs on the top Push the tabs of the of the hard cover to the bottom of the hard cover cutouts of the display strongly (2 places). unit. Hard cover How to attach the hard cover Cable running Before you install the display unit, run all cables you use. See the in
ページ11に含まれる内容の要旨
1. MOUNTING, WIRING 1.2 Flush Mounting, Fixed at Rear This is the standard installation method. 1. Make a cutout in the mounting location with the “Flush mounting template” (included). 364±1 (14.33”) 4-ø18(0.71”) 9 (0.35”) 2. Attach the flush mounting sponges H15 and V15 in the order shown in the figure below. Flush Mounting Sponge (H15) for top and bottom Flush Mounting Sponge (V15) for right and left 3. Connect all cables at the back of the display unit. See section 1.7. 3 314±1 (12.36”) 9
ページ12に含まれる内容の要旨
1. MOUNTING, WIRING 4. Set the display unit to the cutout. Cutout 5. Screw the wing bolts and the wing nuts of the flush mount fixture so that the protector moves to the mounting plate. Wing Bolt Wing Nut Mounting Plate Protector Flush Mount Fixture 15 Set to the fixture. Set to the fixture. 4
ページ13に含まれる内容の要旨
1. MOUNTING, WIRING 6. Fasten the flush mount fixture 15 to the right and left sides of the rear of the display unit with the washer head screws (6 places). Washer Head Screw Flush Mount Fixture 15 7. Fasten the wing bolts, in the order of the number shown in the figure below so that the protec- tors touch the mounting panel. 8. Fasten the wing bolts tightly, in the order shown in step 7. 9. Fasten the wing nuts tightly. Wing Bolt Wing Nut Mounting Plate Protector Mounting Panel 5
ページ14に含まれる内容の要旨
1. MOUNTING, WIRING 1.3 Flush Mounting, Fixed at Front If you do not have the enough space to fix the display unit from the rear, you can fix it from the front with the Flush mount kit OP26-4 (option). Flush Mount Kit OP26-4 (Code: 001-080-850) Name Type Code No. Qty. Flush Mounting Panel (15) OP26-4-1 001-080-960-00 1 Washer Head Screw M4x10 000-163-836-10 8 Self Tapping Screw 5x20 000-162-609-10 4 Flush Mounting Template C42-00909 000-172-636-10 1 1. Make a cutout in the mounting location wi
ページ15に含まれる内容の要旨
1. MOUNTING, WIRING 3. Attach the flush mounting panel to the display unit from the rear with the washer head screws (8 places). Do not confuse the top and bottom of the panel and check that screw holes on the panel and unit match. Narrow Flush Mounting Panel (15) Wide Washer Head Screw 4. Connect all cables at the back of the display unit. See section 1.7. 5. Set the display unit assembly prepared at the step 3 to the cutout for the mounting location. 6. Fix the display unit to the cutout wi
ページ16に含まれる内容の要旨
1. MOUNTING, WIRING 1.4 Flush Mounting, Fixed at Rear, with hood You can attach a hood when flush mounting the unit from the rear, using the hood assembly OP26-3 (option). Hood Assembly OP26-3 (Code: 001-080-840) Name Type Code No. Qty. Hood (15) Assembly OP26-3-1 001-080-950-00 1 F-Mount Hood Gasket 15 26-005-2305 100-351-710-10 1 Hood Gasket Bottom 15 26-005-2306 100-351-720-10 1 F-Mount Hood Gasket Side 15 26-005-2307 100-351-730-10 2 Hood Fixing Plate 15 26-005-2302 100-351-321-10 2 Knob M
ページ17に含まれる内容の要旨
1. MOUNTING, WIRING 3. Attach the “F-Mount Hood Gasket 15” to the top brim, the “Hood Gasket Bottom 15” to the bottom brim, and then attach the “F-Mount Hood Gasket Side 15” to the right and left sides of the display unit from the rear side as shown the figure below. F-Mount Hood Gasket 15 F-Mount Hood Gasket Side 15 Hood Gasket Bottom 15 4. Follow steps 3 to 9 in section 1.2 to fix the display unit to the mounting location. 5. Loosely fix the knobs (4 pcs.) to the hood fixing plate. 6. Slide
ページ18に含まれる内容の要旨
1. MOUNTING, WIRING 7. Press the top of the hood to fit the knobs in the cutouts. Press Press 8. Fix the hood assembly with the knobs tightly (4 places). 1.5 Desktop Mounting You can fix the display unit to a desktop, using the bracket assembly OP26-2 (option). Bracket assembly OP26-2 (Code: 000-016-268) Name Type Code No. Qty. Mounting Bracket (15) OP26-2-1 001-080-820-00 1 Bracket Support w/knobs OP26-2-2 001-080-830-00 Self-Tapping Screw 5x20 000-162-608-10 4 Binding Head Screw M4x10 000-17
ページ19に含まれる内容の要旨
1. MOUNTING, WIRING 1. Loosen the knobs of the bracket support to separate the mounting bracket from the bracket support. Mounting Bracket (15) Bracket Support Knob 2. Set the mounting bracket to the mounting location with four self tapping screws. Self-Tapping Screw 5x20 Mounting Bracket (15) 11
ページ20に含まれる内容の要旨
1. MOUNTING, WIRING 3. Attach the bracket support to the rear of the display unit with the binding head screws (9 plac- es). Binding Head Screw Bracket Support 4. Connect all cables at the back of the display unit. See section 1.7. 5. Loosen the knobs of the bracket support and set them in the notches on the mounting bracket. Mounting Bracket (15) Knob 6. Adjust the angle of the display unit and fix the knobs tightly. 12
