ページ1に含まれる内容の要旨
ASSEMBLY & OPERATING INSTRUCTIONS
Model: 720-0600
300 400 500
200 600
100
700
800
FOR OUTDOOR USE ONLY
FOR PROPANE GAS USE ONLY
K20Y07P-1
This instructions manual contains important information necessary for the proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the appliance
Follow all warnings and instructions when using the appliance
1
Keep this manual for future reference
ページ2に含まれる内容の要旨
Table of Contents Safety Instruction . . . . . . . . . . . . . . . . . . . . . 2-7 Instructions for Converting to Natural gas . . . . . . . 25 Assembly Instruction . . . . . . . . . . . . . . . . . . 8-12 Gas Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . 26-32 Gas Hook –Up . . . . . . . . . . . . . . . . . . . . . . . 13-14 Care and Maintenance . . . . . . . . . . . . . . . . . . . . . 33-34 Installer Final Check List . . . . . . . . . . . . . . . 14 Trouble Shooting . . . . .
ページ3に含まれる内容の要旨
Safety Instruction continued WARNING ELECTRICAL GROUNDING INSTRUCTIONS This appliance (rotisserie motor) is equipped with a plug and should be plugged directly into a properly grounded receptacle. When installed, must be electrically grounded in accordance with local codes or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1 DO NOT cut or remove the grounding prong from this plug. 1. To protect against electric shock
ページ4に含まれる内容の要旨
Safety Instruction continued WARNING CAUTION: Beware of Flashback CAUTION: Spiders and small insects occasionally Do not try lighting this appliance without reading the spin webs or make nest in the grill “LIGHTING INSTRUCTIONS” section of this manual. burner tubes during transit and warehousing. These webs can lead TESTED IN ACCORDANCE WITH ANS to gas flow obstruction, which could Z21.58 CSA 1.6-2007 STANDARD FOR result in a fire in and around burner tubes. This type of fire is known a
ページ5に含まれる内容の要旨
ページ6に含まれる内容の要旨
Safety Instruction continued SAFETY PRACTICES TO AVOID PERSONAL WARNING INJURY Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch When properly cared for, your grill will provide safe, cooking surfaces, grill housing, lid or any other grill reliable service for many years. However, extreme hot surface while the grill is in operation, or until the care must be used as the grill produces intense heat gas grill has cooled down after use. th
ページ7に含まれる内容の要旨
Safety Instruction continued Do not heat unopened food containers. A build-up of Do not use the grill to cook excessively fatty meats or pressure may cause the containers to burst. other products which promote flare – ups. Use a covered hand when opening the grill lid. Do not operate the grill under unprotected combustible constructions. Use only in well ventilated areas. Do Never lean over an open grill. not use in buildings, garages, sheds, breezeways or other such enclosed areas. Whe
ページ8に含まれる内容の要旨
ページ9に含まれる内容の要旨
Assembly Instruction continued STEP 2: Side Burner Assembly A. Insert valve venturi into the side burner and tighten securely using an adjustable wrench. 300 00 4 500 00 2 00 6 100 800 7 00 B. Push the side burner control knob into the valve steam and tighten it using the Allen Wrench. 200 3 00 4 00 00 5 00 6 1 00 00 7 8 00 C. Push valve into side burner control panel. Insert screws from the front side of control panel and tighten. 2 00 3 00 4005 00 6 00 00 1 800 700 D. Connect ignition wi
ページ10に含まれる内容の要旨
Assembly Instruction continued STEP 3: Battery is inserted for the rotisserie burner. To install the battery, turn the ignition button cap counterclockwise and remove it. Replace the ignition button cap after the battery is installed. 3 00 00 4 2 00 00 5 600 1 00 7 00 00 8 STEP 4: Attach the bar barrier to pre-drilled hole on back panel and bottom panel , secure with screws. 3 00 4 00 500 00 6 200 100 7 00 800 10
ページ11に含まれる内容の要旨
L S C O E Assembly Instruction continued STEP 5: Attach propane gas tank to regulator inlet fitting by turning the regulator clockwise as shown in figure below. LP gas cylinder must be fitted with a listed overfill prevention device (OPD). Open the door and pull out the tray, place the gas tank cylinder in the tank tray , then use retention kit that showed as below diagram to secure the tank cylinder . Make sure tank is leveled with bottom panel for proper vapor withdrawal. g CYLINDER T
ページ12に含まれる内容の要旨
Assembly Instruction continued STEP 6: The screws for rotisserie drive motor bracket are attached to the motor bracket. Remove the screws and install the rotisserie motor bracket as shown in the figure below. Assemble the rotisserie skewer as shown in the figure below. 12
ページ13に含まれる内容の要旨
Gas Hook - Up NEVER CONNECT AN UNREGULATED GAS SUPPLY QCC1 in the standard for compressed gas cylinder LINE TO THE APPLIANCE. USE THE valve outlet and inlet connection ANSI/CGA-V-1. REGULATOR/HOSE ASSEMBLY SUPPLIED. Manifold pressure: 11”(27.94cm) water column (W.C.). This is a liquid propane configured grill. Do not attempt L.P. GAS HOOK-UP to use a natural gas supply unless the grill has been reconfigured for natural gas use. Ensure that the black plastic grommets on the LP cylinder valve
ページ14に含まれる内容の要旨
Gas Hook – Up continued 5. When connecting regulator assembly to the valve, 7. If you have a gas connection leak you cannot repair, hand tighten the quick coupling nut clockwise to a turn gas OFF at supply tank, disconnect fuel line complete stop. Do not use a wrench to tighten. Use from your grill and call 1-800-913-8999 or your gas of a wrench may damage the quick coupling nut and supplier for repair assistance. result in a hazardous condition. 8. Also apply soapy solution to the ta
ページ15に含まれる内容の要旨
Leak Testing GENERAL Only those parts recommended by the manufacturer should be used on the grill. Although all gas connections on the grill are leak tested at the factory prior to shipment, a complete gas Substitution will void the warranty. Do not use the grill tightness check must be performed at the installation until all connections have been checked and do not site due to possible mishandling in shipment, or leak. excessive pressure unknowingly being applied to the unit. Periodica
ページ16に含まれる内容の要旨
Leak Testing continued CAUTIONS Place dust cap on cylinder valve outlet when the cylinder is not in use. Only install the type of dust cap on the cylinder valve outlet that is provided with the cylinder valve. Other types of caps or plugs may result in leakage of propane. The gas must be turned off at the supply cylinder when the unit is not in use. If the appliance is stored indoors the cylinder must be disconnected and removed from the appliance. Cylinders must be stored outdoors in a w
ページ17に含まれる内容の要旨
Operating Instruction GENERAL USE OF THE GRILL AND ROTISSERIE WARNING: IMPORTANT! Each main burner is rated at 14,000 Btu/hr. The main USING THE SIDE BURNER: grill burners encompass the entire cooking area and Inspect the gas supply hose prior to turning the gas are side ported to minimize blockage from falling “ON”. If there is evidence of cuts, wear or abrasion, it grease and debris. The igniter knobs are located on must be replaced prior to use. Do not use the side the lower center port
ページ18に含まれる内容の要旨
Grill Lighting Instruction WARNING: IMPORTANT! TO LIGHT THE MAIN BURNER: BEFORE LIGHTING… Never substitute regulators and hose assembly for those supplied with the grill. If a replacement is Inspect the gas supply hose prior to turning the gas necessary, contact the manufacturer for proper “ON”. If there is evidence of cuts, wear, or abrasion, it replacement. The replacement must be that specified must be replaced prior to use. Do not use the grill if in the manual. the odor of gas i
ページ19に含まれる内容の要旨
Grill Lighting Instruction continued FLAME CHARACTERISTICS Check for proper burner flame characteristics. Burner flames should be blue and stable with no yellow tips, excessive noise, or lifting. If any of these conditions exist call our customer service line. If the flame is yellow, it indicates insufficient air. If the flame is noisy and tends to lift away from the burner, it indicates to much air Each burner is adjusted prior to shipment; however, variations in the local gas supply may
ページ20に含まれる内容の要旨
Lighting Illustration Main & Side Burner Lighting Illustration Rotisserie Burner or Searing Burner Lighting Illustration Step 1. Make sure the Lid is open Step to light the Rotisserie Burner : Push and turn the Rotisserie Burner Knob to “IGNITE/ON” position and hold for 3-4 seconds then push electronic ignition button at the same time, until burner is lit. Step 2. Push and turn main or Side Burner knobs to “IGNITE/HI” position. Pilot torch will light. Hold for 3-4 seconds until burner
