ページ1に含まれる内容の要旨
® ®
®
Aussie
b by y M Me ec co o
LP Gas Grill
Assembly and Use Manual
T TM M
Koala
M MO OD DE EL L 7 79 90 00 0 S Se er ri ie es s L Li iq qu ui id d P Pr ro op pa an ne e G Ga as s G Gr ri illll
FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
For Customer Service, call 1-800-251-7558 or visit our web site at www.meco.net
• Failure to follow these instructions could result in fire or explosion which could cause death,
serious personal injury, or property damage.
• Read and follow instr
ページ2に含まれる内容の要旨
— NOTICE — MECO CORPORATION STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YOU NEED TROUBLESHOOTING INFORMATION, PLEASE CONTACT US USING OUR TOLL FREE NUMBER. THANK YOU FOR PURCHASING A MECO CORPORATION PRODUCT. 1-(800)-251-7558 CONSUMER SERVICE DEPARTMENT 8 am - 6 pm E.S.T Mon. - Fri. MECO CORPORATION 1-(423)-639-1171 (TELEPHONE) 1500 INDUSTRIAL ROAD www.meco.net 1-(423)-639-2570 (FAX) GREENEVILLE, TN. 37745 USA CONTENTS I. Assembly Inst
ページ3に含まれる内容の要旨
PARTS ILLUSTRATIONS If you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you have any questions which require help, contact Customer Service and be sure to mention the model number of your grill. (3) Cylinder Retainer Clip (1) Owner’s Manual (4) Left Front Wheel Leg (2) Bottom Shelf (5) Left Rear Wheel Leg (8) Screw, M5x35mm (7) Right Rear Fixed Leg (6) Right Front Fixed Leg (9) Axlewith Item (11) installed (13) Hood (11) Axle Nu
ページ4に含まれる内容の要旨
(36) Bolt, M6x75 2 pc (35) Side Burner Grid (37) Heat Shield (38) Handle Spacer (39) Hood Handle (40) Flame Diffuser (41) Cooking Grid (42) Warming Rack (44) Main Burner (43) Fabric Panel (46) Main Burner (45) LP Cylinder (47) Control Panel Electrode Heat Shield w/Manifold and Regulator 4
ページ5に含まれる内容の要旨
0 03 3..6 62 22 22 2..0 02 2 5
ページ6に含まれる内容の要旨
To reduce the risk of a cut injury: · Wear protective gloves when handling parts that have sharp edges. · Some assembly may require help from another person. Observe where noted. TOOLS: and/or or STEP 1) Cart Assembly: 3 Attach the Legs to the Bottom Shelf with (8) M5 X 35 SCREW M5 x 35 Bolts threaded into the Bottom 8 pcs Shelf holes. Position legs with the holes (2) BOTTOM SHELF exactly as indicated . (3) LP CYLINDER CLIP (4) LEFT FRONT (5) LEFT REAR WHEEL LEG WHEEL LEG (6) RIGHT FRONT (7) RI
ページ7に含まれる内容の要旨
STEP 2) Assemble Axle, Wheels & Wheel Covers: (9) with Item (11) installed (11) Nut, M8 (12) WHEEL COVER 2 PCS 2 PCS (10) WHEEL 2 PCS (9) AXLE (10) WHEEL (11) Nut, M8 WHEEL LEGS (12) WHEEL COVER Push Axle through holes in Wheel Legs. Place Wheels on both ends of Axle, then tighten with two M8 Nuts with wrench or pliers. Align Wheel Cover pins with 3-holes in Wheel and snap flush against wheel. FIG. 2 Step 3) Assemble Hood/Bowl to Cart: (16) M6 Locknut (15) Screw, M6X35 4 pcs 4 pcs Bo
ページ8に含まれる内容の要旨
Align groove Step 4) Install Drip Cup: with vertical wire Insert Drip Cup into Drip Cup Holder ring until the cup flange is flush with the ring and the notch in the lip of the cup fits the vertical hanger wire. (17) Drip Cup Step 5) Assemble Sidebraces and Rear Crossbrace: · Attach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG. 5A) Secure Bottom Heat Shield to Left Sidebrace with M4x10 Screws and M4 Wingnuts. (FIG. 5B) Allow Heat Shield Edge to overlap Sidebrace edg
ページ9に含まれる内容の要旨
Step 6) Assemble Side Tables: Align bracket holes of Left and Right Side Tables with holes in Bowl Leg Brackets. Attach Side Tables with M6X15 Screws underneath. (26) Right Side Table (27) Left Side Table (28) Screw, M6x15 8 pcs FIG. 6B (28) Screw, M6X15 (28) Screw, M6x15 FIG. 6A Step 7) Assemble Side Burner Valve and Knob: · Align Valve Stem and Bracket holes with holes in Side Table. Attach M4 x 10mm Screws to Valve brackets and tighten. (FIG. 7A) · Push Control Knob onto the valve stem.
ページ10に含まれる内容の要旨
Step 8) Assemble Side Burner Electrode and Side Burner: · Feed Electrode wire through upper left hole from large center hole in Side Burner Reflector. (FIG. 8A) Allow electrode to follow wire into hole and lie flat. (8B) (32) Side Burner Electrode 1 pc Electrode Wire Side Burner through hole Electrode (33) Side Burner 1 pc (23) Wingnut, M4 1 pc FIG. 8A (35) Side Burner Grid FIG. 8B 1 pc · Insert Side Burner tube through large hole in Side Burner Pan. Allow threaded stud to go through hole in
ページ11に含まれる内容の要旨
· Align prongs of Side Burner Grid with holes in Side Table and lower grid into the holes. Side Table Assembly Finished (FIG. 8F) (35) Side Burner Grid FIG. 8F FIG. 8G Step 9) Attach Hood Handle and Shield: Open Hood. Insert M6 Bolts through Heat Shield, Hood, through large end of Handle Spacers and to the Handle. Tighten bolts into the Handle inserts. Do not over tighten; the porcelain grill coating may crack. (39) Hood Handle (36) Bolt, M6x75 2 pcs (38) Handle Spacer (37) Hood Heat Shield (3
ページ12に含まれる内容の要旨
Step 10) Install Flame Diffuser: Flame Diffuser mounting stud in Bowl. Place the Flame Diffuser over the Main Bowl Burner, onto the two mounting studs on each side of the Bowl. (FIG.10) (40) Flame Diffuser (40) Flame Diffuser FIG. 10 4 (41) Warming Rack 1 pc 2 (41) Warming Rack (42) Cooking Grid 1 pc 3 Step 11) Install Warming Rack/Cooking Grid: 1 Position Warming Rack as shown. (FIG. 11A) FIG. 11A Insert legs 1 and 2 in holes on right side of grill Bowl and Hood respectively. While holding leg
ページ13に含まれる内容の要旨
CONNECTING/DISCONNECTING THE GAS USING GAS · Never fill the LP gas cylinder more than 80% of cylinder volume. (20 lb. maximum) Do not ask the propane supplier to over-fill the cylinder. · If you obtain LP gas through a cylinder exchange CARBON MONOXIDE HAZARD dealer, make sure you get a safe and adequate O.P.D. · This appliance can produce carbon monoxide which cylinder. (See page 22) Use only a licensed LP gas has no odor. Using it in an enclosed space can kill you. cylinder dealer. · Ne
ページ14に含まれる内容の要旨
3) Lift and swing LP Cylinder Retainer Clip to outside of grill. Set LP cylinder in the large hole inside the Bottom Shelf. Rotate the LP Make sure hose is cylinder toward the front of grill so regulator routed outside and hose may connect. (FIG. 13A) under crossbrace. Rotate Cylinder Cylinder Retainer Clip Hand tighten coupling nut in clockwise direction FIG. 13A Remove 4) Swing the Cylinder Retainer Clip over round FIG. 13C Protective Cap shoulder of the LP cylinder. Exert pressure at e
ページ15に含まれる内容の要旨
6) Check for leaks by brushing the soap solution SELECTING A LOCATION on all gas valves, hose connections and fittings. (shown by the heavy arrows in (FIG. 14A, 14B To reduce the risk of serious bodily injury or death: & 14C) Make sure you generously brush the · This outdoor cooking appliance shall be used only locations with the soap solution, completely outdoors and shall not be used in a building, garage, surrounding the connections and fittings. or any other enclosed area. Locate out
ページ16に含まれる内容の要旨
Control Knob in OFF position Side Burner fittings FIG.15A under Side Table FIG. 14C LIGHTING THE GRILL USING THE IGNITOR To reduce the risk of serious bodily injury or death: · Open Hood before lighting the grill to prevent an explosion from any gas accumulation. · If lighting attempts fail, or the burners go out during FIG. 15B operation, turn all control knobs “Off” to dissipate any accumulation of gas. Accidental ignition could occur. Right Control Knob Left Control Knob Wait five minutes
ページ17に含まれる内容の要旨
MANUAL LIGHTING THE GRILL LIGHTING THE SIDE BURNER To reduce the risk of serious bodily injury or death: To reduce the risk of serious bodily injury or death: · If lighting attempts fail, or the burner goes out during · Open Hood before lighting the grill to prevent an operation, turn control knob “Off” to dissipate any explosion from any gas accumulation. accumulation of gas. Accidental ignition could occur. · If lighting attempts fail, or the burners go out during Wait five minutes before
ページ18に含まれる内容の要旨
MANUAL LIGHTING THE SIDE BURNER Cooking on the Grids: The burners heat up the Flame Diffusers under the Cooking Grids, which in turn heat the food on the grill. The natural food juices from cooking fall onto the hot Flame Diffusers below and vaporize. Rising smoke bastes To reduce the risk of serious bodily injury or death: the food, giving it that unique barbecued flavor. · If lighting attempts fail, or the burner goes out during operation, turn control knob “Off” to dissipate any CAUTION acc
ページ19に含まれる内容の要旨
3) Turn off the gas at the LP cylinder valve by turning the · Do not use the grill without the Drip Cup in place. handle clockwise until it stops. Empty excess grease to avoid a fire under the grill. 4) Wait until the grill is cool before closing the hood, cleaning · If you notice grease or other hot material dripping or putting on the cover. from the grill onto the valve, hose, or regulator, turn 5) Regularly clean your LP gas grill between uses and after off the gas supply immediately
ページ20に含まれる内容の要旨
5) Use a pipe cleaner to clear insect nests from the inlet hole of main burner (FIG. 20C) and side burner ventilation hole. (FIG. 20D) Open up the main burner holes and the To reduce the risk of a fire beneath the grill: side burner holes with a small nail or wire.Normal wear · Inspect and clean burner/venturi tubes for insects and and corrosion may enlarge some holes, however, if large insect nests. cracks or holes are found, replace the Burner. Use a · Be sure burners are re-installed p
