ページ1に含まれる内容の要旨
OWNER’S MANUAL
™
Gourmet Series Marine Gas Grill
Model A10-918
For questions regarding performance, assembly,
operation, parts, or returns, contact the experts
at MAGMA by calling TOLL FREE IN U.S.A. AND
CANADA 1-800-86-MAGMA
7:00 a.m. - 5:00 p.m. Pacific Time Monday thru
Friday or e-mail us at mail@MagmaProducts.com
Read all instructions before operating. Save manual for future reference.
ページ2に含まれる内容の要旨
IMPORTANT SAFETY WARNINGS READ ALL INSTRUCTIONS BEFORE OPERATING. • USE OUTDOORS ONLY. • DO NOT USE THIS APPLIANCE INSIDE THE BOAT OR ANY ENCLOSED SPACE. • GRILLS RADIATE HEAT. CLEARANCE FROM COMBUSTIBLES, 24” SIDES AND BACK. NEVER USE UNDER AWNINGS, PATIO COVERS, ETC. • USE PROPANE GAS ONLY. FUEL STORAGE SHOULD BE IN COMPLIANCE WITH THE AMERICAN BOAT AND YACHT COUNCIL (ABYC) STANDARDS A-1 (9), MARINE LIQUIFIED PETROLEUM GAS (LPG) SYSTEMS. • FOR NATURAL GAS APPLICATION CONTACT MAGMA. • ALWAYS LI
ページ3に含まれる内容の要旨
MOUNT HARDWARE Fasteners are supplied for both Single Mount and Dual Mount grill mounting options. See Magma Catalog or Website for best mount selection. Single mount through-bolt Dual mount applications applications 4 Carriage bolts & lock nuts. Only 4 bolts 4 Carriage bolts & lock nuts. required for grill mounting. Place bolts (2 per side) diagonally from each other as shown. Single mount non-through-bolt applications, including Style 1 “Levelock” Carriage bolt Hex head bolt 4 Hex head bolts
ページ4に含まれる内容の要旨
OPERATING PROCEDURES OPERATE ONLY ON “LOW” WHEN LID IS CLOSED. ALWAYS OPERATE WITH GREASE TRAY IN PLACE. WARNING: Do not overheat grill. Magma Grills do not require pre-heating. Stainless Steel loses anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low temperature with the lid closed. If medium or high heat is required, grill with lid open. LIGHTING INSTRUCTIONS • Open lid during lighting. • Depress knob and rotate counter-clockwise to the “HIGH” flame
ページ5に含まれる内容の要旨
ELECTRODE SPARK ADJUSTMENT CAUTION: Spark can cause small shock. Do not leave fin- gers on or near electrode wire while engaging igniter. • Electrode wire should be approximately 1/8” from gas exit hole in burner. Carefully adjust wire if required. A DISASSEMBLY & RE-ASSEMBLY • Lift radiant plate up & out of left slot (see B) and remove by sliding it out of right slot (see C). • Remove burner screw (see B) and remove burner. Check burner for grease residue or spider webs that may obstruct gas fl
ページ6に含まれる内容の要旨
MAINTENANCE About Stainless Steel - Stainless steel exposed to prolonged periods of high heat will change color and texture. Magma grills require no preheating. Not preheating will keep your grill cooler and greatly extend the life and beauty of your grill. Texture and color change is normal on interior components and will not affect the product’s operation or performance. Exterior Stainless Steel Components - Cleaning the exterior surface after every use will help prevent discoloration. Use so
ページ7に含まれる内容の要旨
TROUBLE SHOOTING GUIDE Problem Possible Cause Possible Solution Burner will not Igniter electrode covered with Clean igniter electrode light with igniter grease or residue Igniter/electrode too far from Adjust electrode until proper burner spark appears (see page 5) Igniter/electrode wire loose or Reconnect wire between ignit- disconnected er & electrode (see page 5) Wire is shorted causing spark Call Magma from wire before electrode No spark being generated Call Magma Burner will not No gas fl
ページ8に含まれる内容の要旨
Contents A x 4 x 4 B A) (1) 3/16” Hex key wrench for lid removel. C x 4 x 4 B) Pack of (4) 1/4”-20 x 5/8” hex head screws and internal lock washers for “Levelock” single mount application. C) Pack of (4) 1/4”-20 x 5/8” carriage bolts and lock nuts for dual mount and single mount applications and table legs. LIMITED WARRANTY Magma Products, Inc. guarantees this gas grill to be free from defects in materials or workmanship to the original consumer. This guarantee is for the periods herein specifi
