ページ1に含まれる内容の要旨
INSTALLATION
CO.VE BL R G E T, AS GRILL JENN-AIR
MANUAL
JGD8130 & JGD8345
COOKTOP SERIES
DIMENSIONS SHOWNIN BOTHINCHESAND CENTIMETERS
*Blower mayberotated forhorizontal orverticaldirection byloosening nutsaround blower inlet.Accessible inside ventilation
chamber.
• NOTICETO INSTALLER:Leavetheseinstructions withtheappliance.
• NOTICETO CONSUMER:Retaintheseinstructions forfuturereference.
REGULATOR -- APPUANCE PRESSURE
REGULATOR
TIE DOWNBOLT TIEDOWNBOLT
ONEACHEND ONEACHEND ,OVER
GREASE
BLOWER CANB
ページ2に含まれる内容の要旨
Installing Cabinetry OverYourJenn.Air Grill *A = 30" (76.2 ¢m) minimum vertical clearance between of local codes, with the latest edition of the National cooking surfaceand construction above theappliance. Electrical Code ANSI/NFPA No. 70 USA or currant CSA STANDARD C22.1 Canadian Electrical Code part 1. *B = 13" (33.02 cm) maximum depth of cabinets installed above cooking top. I Dottedlines indicate ' rangehood i construction * To eliminate associated potential hazards such as reaching over ope
ページ3に含まれる内容の要旨
Instructions ToInstaller AirShutter Adjustment 1. Chamfer all exposed edges of decorative laminate to This appliance is shipped from the factory with air shutters prevent damage from chipping, adjusted for use with Natural Gas. If further adjustment is 2. Radius corners of outout and file to insure smooth necessary,or to reset for usewith LP, adjustair shuttersas edges and prevent corner cracking. Recommend follows: 1/4" or 3/8" diameter drill in each corner, Grill BurnerandSurfaceBurnerCartridg
ページ4に含まれる内容の要旨
LowFlameAdjustment (See Illustration "C") Pressure Testing This appliance is shipped from the factory with low and The maximum gas supply pressure for the appliance medium flame settings adjusted for use with Natural Gas. If pressure regulator supplied on this appliance is 14" W.C. further adjustment is necessary, or to readjust for use with The test pressure for checking this appliance pressure LP, proceed as follows: regulator must be at least 6" W.C. for Natural Gas, and at least 11" W.C. for
ページ5に含まれる内容の要旨
Conversion ToLPGas This appliance is shipped from the factory equipped for use _.j, / with Natural Gas. To convert it from Natural Gas for usewith LP Gas, perform steps 1 through 4. lf2" OPEN END WRENCH ! orifice hoods supplied, located in a pack attached to the outer plenum area of this appliance. (See Illustration "E" TURN below, and LP Gas Conversion Instructions on page 6). CLOCKWISE TOTIGHTEN 2. Invert cap in convertible appliance pressure regulator (if TURN • 1. Remove natural gas odflce h
ページ6に含まれる内容の要旨
TOCONVERT APPLIANCE FORUSEWITHPROPANE GAS NaturalGasTo PropaneGas(LP)Conversion Instructions Models- JGD8130 &JGD8345 Series _ -- (_) Manifold- PropaneGas pressurerequired- 10" W.C. Incoming Propane Gas pressure requiredto appliance pressure regulator- 11" - 12" W.C. APPUANP CRESSUR E Propane Gas conversionorificehoodsare suppliedwith these models. Propane Gas input specified - JGD8130/JGD8345 - E 33,000 BTU/hr / 51,000 BTU/hr. JGD8345 (Shown) INCHES BURNER BTU/hr ORIFICE DIAMETER COLOR Left Rea
ページ7に含まれる内容の要旨
TOCONVERT APPLIANCE FORUSEWITHNATURAL GAS PropaneGas(LP)ToNatural Gas Models - JGD8130 &JGD8345 Series Conversion Instructions Manifold - NaturalGas pressurerequired- 5" W.C, If this appliance has been convertedfor use with LP Gas, Incoming Natural Gas pressure required to appliance each of the followingmodifications mustbe performedto pressureregulator- 6" - 7" W.C. convertthe unit back to NaturalGas. NaturalGas inputspecified,Model JGD8130/JGD8345 - 36,000 BTU/hr / 56,000 BTU/hr. A. Replaceall
ページ8に含まれる内容の要旨
REQUIRED ADJUSTMENTS ATTIMEOFINSTALLATION The installation of this appliance mustconformwithlocalcodes, or intheabsence of localcodes,with thelatesteditionoftheNationalFuelGasCodeANSIZ223.1 USAor currentCAN/CGA-B149Installation Code. I_-'1 Thisrangewasmanufactured forusewithNaturalGas.IfLPgasisthefuelofchoice,followtheconversion to LP procedurefoundinthe installationinstructions. '-'-]Test allexternalconnectionsfor gasleaks.Nevertestforgas leakswithan openflame. I----I Test all electricalconnect
