ページ1に含まれる内容の要旨
LP Gas Grill
Model # DGP350NP/DGP350NP-D
USER’S MANUAL AND OPERATING INSTRUCTIONS
ANS Z21.58a – CSA 1.6a-2008
Outdoor Cooking Gas Appliance
Assembler/Installer: This manual contains important information necessary for the proper
assembly and safe use of this appliance. Read and follow all warnings and instructions before
assembling and using this appliance. Leave these instructions with the consumer.
Consumer/User: Follow all warnings and instructions when using this appliance.
Retain these
ページ2に含まれる内容の要旨
LP Gas Grill STOP! NO NEED TO RETURN TO THE STORE Questions With The Assembly? Require Parts Information? Product Under Manufacturers Warranty? Call Toll Free : 1-877-447-4768 8:30 a.m. – 4:30 pm CST, Monday – Friday Retain This Owner’s Manual And Proof Of Purchase For Future Reference To help us help you Fill in the information below: Date of Purchase Place of Purchase Model Number Product Serial No. MODEL NUMBER AND PRODUCT SERIAL NUMBER CAN BE FOUND ON THE RATING LABEL OF YOUR GRILL. 1
ページ3に含まれる内容の要旨
LP Gas Grill TABLE OF CONTENTS Safety Information .............................................................................................. 2 - 3 Package Contents ............................................................................................. 4 - 5 Illustrated Parts List .......................................................................................... 6 - 7 Hardware Contents ..............................................................................
ページ4に含まれる内容の要旨
LP Gas Grill SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-877-447-4768, 8:30 a.m. – 4:30 pm CST, Monday – Friday 1. DO NOT store or use gasoline or any other flammable vapors and liquids within 25 feet (8 m) of this or any other appliance. 2. An LP Cylinder not connected for use should be stored a minimum of 10 feet (3 m) away
ページ5に含まれる内容の要旨
36 in. (914.4mm) LP Gas Grill SAFETY INFORMATION WARNING Do not place the grill under overhead combustible construction or awnings. Minimum clearance from sides and back of unit to combustible construction, 36 inches (914.4mm) from sides and back. NOTE: The installation must conform with local codes or, in the absence of local codes, with either the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Natural Gas and Propane Installation Code, CSA B149.1, or Propane Storage and Handling Code, B1
ページ6に含まれる内容の要旨
LP Gas Grill PACKAGE CONTENTS BEFORE STARTING ASSEMBLY, UNPACK CARTON AND VERIFY CONTENTS. COMPARE ENCLOSED PARTS WITH PACKAGE CONTENTS LIST AND DIAGRAM. IF ANY PART IS MISSING OR DAMAGED, DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT. CONTACT CUSTOMER SERVICE FOR REPLACEMENT PARTS. 1-877-447-4768 8:30 a.m. – 4:30 pm CST, Monday – Friday. Part No. Description Qty Part No. Description Qty 1 1 Bottom Shelf 1 12 12 Grill Body 1 13 2 Locking Caster 2 13 Control Knob 2 2 3 3 Caster 2 14 14 Collapsible
ページ7に含まれる内容の要旨
LP Gas Grill PACKAGE CONTENTS 18 17 12 17 16 19 14 15 21 4 22 13 13 11 9 20 6 7 8 5 10 3 1 2 3 2 4 5
ページ8に含まれる内容の要旨
LP Gas Grill ILLUSTRATED PARTS LIST Bottom Shelf Locking Caster Caster 1 2 3 Cart Left Side Panel Cart Right Side Panel Cylinder Holder 3 5 6 Pin Cart Rear Panel Down Upper Door Brace 7 8 9 Door Assembly Cart Swivel Rear Panel Upper Grill Body 10 11 12 6 7
ページ9に含まれる内容の要旨
LP Gas Grill ILLUSTRATED PARTS LIST Control Knob Collapsible Shelf Support A Collapsible Shelf Support B 13 14 15 Heat Tent Cooking Grate Warming Rack 16 17 18 Left Shelf Right Shelf Grease Cup Clip 19 20 21 Grease Cup 22 6 7
ページ10に含まれる内容の要旨
LP Gas Grill HARDWARE CONTENTS Part No. Description QTY Illustration M6x12 A 30 Scr ew M4x10 4 B Flat Head Screw M6 4 C Step Screw M6x25 4 D Round Head Screw M5x12 16 E Scr ew 6MM F 16 Spring Washer 6MM G 16 Flat Washer Tools Required for Unpacking, Assembly and Leak Testing of This Product: Phillips Screwdriver Spray Bottle Estimated Assembly Time: 30-45 minutes 8 9
ページ11に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS 3 2 Step 1 1. Secure each locking caster (2) to the back side (side that is beveled for access to locking mechanism when assembled and upright) of the bottom shelf (1) using four screws (A) four spring 1 washers (F) ) and four flat washers (G). Then tighten all screws. 2. Install the casters (3) to the front side (not beveled) of bottom shelf using four Back Side Beveled Back Side Beveled screws (A) four spring washers (F) ) and four flat washers (G). T
ページ12に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS 4 Step 3 1. Attach the cart left side panel (4) to the bottom shelf (1) with A two screws (A), but do not fully tighten. 2. Attach the cart right side panel (5) to the bottom shelf (1) in the same way. 4 A 1 5 Hardware Used M6x12 A 4 pc Scr ew A: M6x12 Screw 1 5 Qty: 4pcs Step 4 Install two screws (A) into the cart left side panel and two screws (A) into the cart right side panel (5) as illustrated at right. Do not fully tigh
ページ13に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS 4 8 5 Step 5 1. Align the key holes in the cart rear panel (8) with the 4 screws just installed into the cart left and right side panels. Push cart rear panel (8) onto screws and down to meet bottom shelf (1). 2. Secure the cart rear panel (8) to the bottom shelf (1) with two screws (A). Next, tighten the 4 screws on the cart left and right side panels (4 and 5). 1 A Tighten Screw (A). Hardware Used M6x12 A 2 pc Scr ew Step 6 5 Sec
ページ14に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 7 Install the door assembly (10) to the cart left side panel (4) with four flat head screws (B) and tighten. 4 B 10 Hardware Used M4x10 B 4 pc Scr ew Step 8 FULLY TIGHTEN ALL SCREWS AT THIS TIME. NOTE: When not in use put the match holder into the hole of door inner as shown below. 10 4 B 12 13
ページ15に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 9 5 C 1. Secure the cart swivel upper rear panel (11) to the cart left side panel (4) and cart right side panel (5) with two screws (C). Then install another 2 screws (C) into the upper mounting holes of the left and right side panels. These will secure the cart swivel upper rear panel (11) when it is in 4 the closed position. 11 2. Rotate the cart swivel rear panel upper (11) upwards until the two screws 11 (C) on the cart left and right sid
ページ16に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 11 12 1. First, lock the back two casters to ensure the cart doesn’t move while installing the grill body (12). 2. Carefully place the grill body (12) over the mounting tabs on the cart side panels and onto the cart. Make sure the gas hose is inside the cart. Align the holes in the grill body with the holes in the mounting tabs. Fasten the grill body (12) in place with four screws (D). 2 12 D Hardware Used M6x25 D 4 pc Scr ew
ページ17に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 12 Install the collapsible shelf support A (14) and collapsible shelf support B A 14 B 15 (15) on both sides of the 15: Collapsible Collapsible grill body using hardware Shelf Support B Shelf Support part E (M5x12 screw). Qty: 2 pcs E 14 15 12 Hardware Used M5x12 E 16 pc Scr ew Step 13 WARNING: IT IS VERY IMPORTANT TO CHECK AND ENSURE THAT EACH AND EVERY BURNER IS FULLY ENGAGED WITH THE ADjACENT
ページ18に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 14 Place two cooking grates (17) on the grill body brace and grill rear panel. 17 Step 15 Install the warming rack (18) as illustrated below. 18 16 17
ページ19に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 16 Align the left shelf (19) to the shelf support and insert between shelf supports, then swing the left shelf 90 degrees up and push shelf against grill body. Finally, press down on side shelf close to grill body until it is fully fastened to the shelf support. Install the right shelf (20) in the same way. Shelf Support Swing shelf up 90 degrees Press down Push 16 17
ページ20に含まれる内容の要旨
LP Gas Grill ASSEMBLY INSTRUCTIONS Step 17 Open the cart swivel upper rear panel (11) and hang the grease cup clip (21) onto the bottom of the grill body by pushing the small top part of the grease cup clip (21) into the hole in the bottom of the grill body. Place the grease cup (22) into the grease cup clip. Close the cart swivel upper rear panel. Grease cup clip Grease cup Close the cart swivel 11 21 22 upper rear panel. Step 18 Open the door and place a gas cylinder (not included) fill
