ページ1に含まれる内容の要旨
PRODUCT GUIDE
MODEL 463250512
T-36D
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
IMPORTANT: Refer to the
instructions inside when
converting this grill to
Natural Gas.
© 2011 Char-Broil, LLC Columbus, GA 31902 Assembly instructions © 2011
ページ2に含まれる内容の要旨
TABLE OF CONTENTS DANGER For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 If you smell gas: Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 1. Shut off gas to the appliance. Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2. Extinguish any open flame. Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3. Open lid. Parts Di
ページ3に含まれる内容の要旨
WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could 1. Combustion by-products produced when using exceed weight limit of the this product contain chemicals known to the State of side burner shelf or side shelf, California to cause cancer, birth defects, and other reproductive harm. resulting in failure 2. This product contains chemicals, including lead of grill cart components. and lead compounds, known to the State of California to cause cancer, birth
ページ4に含まれる内容の要旨
LP Cylinder USE AND CARE •The LP cylinder used with your grill must meet the following requirements: •Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near •LP cylinders must be constructed and marked in accordance the appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for Cana
ページ5に含まれる内容の要旨
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinde
ページ6に含まれる内容の要旨
Straight Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP cylinder. 3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4.Brush soapy solution onto areas circled below, or other similar Hold coupling nut and regulator fittings on your grill. as shown for proper connection
ページ7に含まれる内容の要旨
Safety Tips Before opening LP cylinder valve, check the coupling nut for WARNING tightness. When grill is not in use, turn off all control knobs and LP For Safe Use of Your Grill and to Avoid Serious cylinder valve. Never move grill while in operation or still hot. Injury: Use long-handled barbecue utensils and oven mitts to avoid • Do not let children operate or play near grill. burns and splatters. • Keep grill area clear and free from materials that burn. Maximum load for side
ページ8に含まれる内容の要旨
Burner Flame Check WARNING •Remove cooking grates and troughs. Light burners, rotate knobs from to . You should see a smaller flame in Turn controls and gas source or tank OFF when not position than seen on . Perform burner flame check on sideburner, also. Always check flame prior to each use. If in use. only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section. CAUTION If ignition does NOT occur in 5 seconds, turn the burn
ページ9に含まれる内容の要旨
Cleaning the Burner Assembly CAUTION Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas OFF at control knobs and LP cylinder. 2. Remove cooking grates and troughs. SPIDER ALERT! 3. Remove cotter pins and carryover tubes from front of burners. 4. Remove cotter pin and lift burner to disengage from SPIDER AND WEBS bracket on firebox. INSIDE BURNER TUBE 5. Use flat blade screwdriver to pry off electrode from burner. Electro
ページ10に含まれる内容の要旨
LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for re
ページ11に含まれる内容の要旨
PARTS LIST Key Qty Description Key Qty Description A1 TOP LID OO 1 ELECTRODE, F/ SIDEBURNER B 1 HANDLE, F/ TOP LID PP 1 SIDEBURNER GRATE C 2 END CAPS, F/ HANDLE QQ 2 CASTER, LOCKING D 1 LOGO PLATE, W/ TEMP GAUGE RR 2 CASTER, FIXED E 1 HARDWARE F/ TOP LID SS 1 IGNITOR WIRE, F/ SIDEBURNER F 2 RUBBER BUMPER, RECTANGLE TT 1 GROMMET G 4 RUBBER BUMPER, ROUND UU 1 TANK SCREW H 1 FIREBOX I 1 MATCH HOLDER AND CHAIN J 3 MAIN BURNER ELECTRODE, F/ MAIN BURNER, K1 900MM WIRE ELECTRODE, F/ MAIN BURNER, L2 60
ページ12に含まれる内容の要旨
PARTS DIAGRAM E F D G A H MM C C M M LL B LL J LL J Z J EE G I L L K II P Q N FF PP R X JJ O OO Y GG NN SS KK Q W R V HH U BB T BB TT DD AA S CC QQ QQ UU RR RR 12
ページ13に含まれる内容の要旨
Front ASSEMBLY Place bottom shelf upside down. Insert Bent U Pin into the caster mounting plate to lock it in place, shown A. 1 Spin the caster clockwise into the threads on the bottom shelf until secure. Remove the Bent U Pin and repeat for remaining casters. Make sure the two locking casters are secured at the rear and the non-locking casters are secured at the front. After all 4 casters are secure remove the Bent U Pin and save for future maintenance. A Non-lock caster Bent U pin Locking cas
ページ14に含まれる内容の要旨
Place lower back panel between side 3 panels at rear of bottom shelf. Secure lower back panel to side panels using two 1/4-20x1/2” screws on each side. 1/4-20x1/2” screw Lower back panel This step requires two people 4 to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Grill head Re
ページ15に含まれる内容の要旨
Note: DO NOT over tighten screws and washers that come into contact with porcelain coated surfaces. Over tightening may cause the porcelain coating to crack and break, resulting in exposed metal that will be prone to rust. Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and facing the front. 5 Secure upper holes using one 1/4-20x1½” screw and fiber washer on each side. Secure lower holes using one 1/4-20x1½” screw on each s
ページ16に含まれる内容の要旨
screws, Attach right side fascia to right side shelf using four #10-24x3/8” 5mm lock washers and 5mm flat washers, shown A. 7 Insert flange on right side shelf into side shelf brackets on right side of firebox, shown B. Attach right side shelf to firebox using two 1/4-20x3/4” screws and 1/4” nuts, shown C. Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown D. Attach rear of shelf using one 1/4-20x1½” screw, shown E. A B 5mm Flat Washer 5mm Lock Washer
ページ17に含まれる内容の要旨
left side fascia left side shelf Attach left side fascia to left side shelf using four #10-24x3/8” screws, 5mm lock washers and 5mm flat washers, shown A. 8 Insert flange on left side shelf into side shelf brackets on side of firebox, shown B. Attach left side shelf to firebox using two 1/4-20x3/4” screws and 1/4” nuts, shown C. . Attach front of shelf using two #8x3/8” self-tapping screws and large flat washers, shown D. Attach rear of shelf using one 1/4-20x1½” screw, shown E. B A side she
ページ18に含まれる内容の要旨
First, remove the two screws and lock washers attached to the sideburner valve bracket. 9 Position sideburner valve bracket beneath sideburner shelf fascia so that valve stem comes through larger center hole in fascia. Align the holes on valve bracket with left and right holes on fascia. Secure using screws and lock washers that were removed from bracket, shown A. Place sideburner bezel over valve stem on front side of fascia. Align small holes on bezel with upper and lower holes on fascia. A
ページ19に含まれる内容の要旨
Insert sideburner into left shelf. The stud on bottom of the burner fits into the rear small hole in sideburner drip pan, shown A. 10 Make sure burner tube engages sideburner valve, shown B. Secure burner to sideburner drip pan with Wing nut, shown B. Under sideburner shelf, attach sideburner ignitor wire to electrode. Place sideburner cooking grate onto sideburner shelf, aligning grate legs with holes in shelf, shown C. A Sideburner Sideburner drip pan Burner tube B Electrode Burner tube Sideb
ページ20に含まれる内容の要旨
Connect each of the wires from the main burner electrodes, and sideburner electrode into the back of the Electronic Ignition 11 Module.Total (4) connections. Connect the two wires[(a) and (b)] from the switch wiring harness into the back of the Electronic Ignition Module. Total (2) connections, shown A. Unscrew the cap and nut from electronic ignition module. Attach electronic ignition module to the cart left side panel with the nut, shown B. Insert AA battery into ignition module, negative (
