ページ1に含まれる内容の要旨
OWNER'S MANUAL
RET Series
Read all instructions carefully before use.
For any Customer Support needs please choose the
Customer Support tab on www.royalsovereign.com
Royal Sovereign International Inc.
www.royalsovereign.com
ページ2に含まれる内容の要旨
RET Series TABLE OF CONTENTS TOPIC ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙PAGE 1. INTRODUCTION ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3 2. SAFETY PRECAUTIONS ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 3 3. PRODUCT IDENTIFICATION ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙ 5 4. INSTALLATION ∙ ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙
ページ3に含まれる内容の要旨
RET Series 1. INTRODUCTION Thank you for choosing a Royal Sovereign trimmer. It has been designed and manufactured to provide years of continuous service. For complete operating and maintenance information please read this manual thoroughly. Upon receipt of your trimmer, please inspect the box, the machine and all other contents for shipping damage. Damage should be brought to the immediate attention of the delivering carrier (See page 7 for list of shipment elements). 2. SAFETY PRECAU
ページ4に含まれる内容の要旨
RET Series Dangerous areas and residual risks All the areas around the machine in which people are at risk of injuries or health problems are considered dangerous. Pay close attention to hands when operating the trimmer. During certain intervention procedures on the machine, which are pointed out each time in this manual, residual risks for the operator may arise. Residual risks can be avoided by carefully complying with the procedures of this manual and using the personal protection device
ページ5に含まれる内容の要旨
RET Series 3. PRODUCT IDENTIFICATION 12 1 11 10 2 9 3 4 8 5 7 6 NO PART NAME 1 Left Side Cover 2 Power Switch 3 Feed Table Front 4 Fabric Holder Rod 5 Protection Plate 6 Foot Pedal 7 Floor Stand 8 Waste Catcher 9 Right Side Cover 10 Rear Cover 11 Activation Bar 12 Safety Cover 5
ページ6に含まれる内容の要旨
RET Series 4. INSTALLATION Note: The trimmer should be installed by a trained service technician The trimmer needs to be assembled by a trained installer. The trimmer should only be used in an area with the following characteristics: •∙Pr otecti on∙fr om∙atmosph eri c∙a g en ts •∙Pr oper∙i l lu mi n ati on •∙T emper atu r es∙between∙64°∙F∙an d∙95°∙F •∙A mou n t∙of ∙h u mi di ty∙fr om∙30%∙to∙80% 4.1 Electrical requirements Royal Sovereign recommends that a licensed electrician ensures proper pow
ページ7に含まれる内容の要旨
RET Series 4.2 Box contents Thoroughly inspect the parts and the unit. It is imperative that any missing parts are reported and a claim is filed with the reseller immediately upon receipt of shipment. Part Name Quantity Picture Main Trimmer Assembly 1 Floor Stand Side Frame 2 Floor Stand Cross Bar 2 Owner's Manual 1 Protection Plate (RET-1500/RET-2000) 1 Main Protection Plate (RET-2500) 2 Lamp (RET-1500) 1 Box Lamp (RET-2000) 2 Lamp (RET-2500) 2 Connection Socket (RET-2000/RET-2500) 1 Wastec
ページ8に含まれる内容の要旨
RET Series 4.3 Assembly 1. Open the box carton and remove all parts. 2. Open the tool-box. (Fig. 4-1) Fig. 4-1 This operation must be carried out by a minimum of two people 3. Attach the lower cross bar to the left floor stand side frame and right floor stand side frame using the supplied screws (M8x55). (Fig. 4-2) 4. Attach the upper cross bar (Fig. 4-3) to the floor stand side frames using the supplied screws (M8×15). 5. Attach the protection plate (Fig. 4-4) to the upper cross bar with the
ページ9に含まれる内容の要旨
RET Series 6. Mount the support brackets for the fluorescent lamp fixture (fig. 4.6) to the back side of the upper cross bar with the supplied screws. Insert the fluorescent lamp fixture into the brackets, and insert the fluorescent bulb into the lamp fixture. (fig. 4.6) Note : For model RET-2000 and RET-2500, connect the 2 supplied lamps before inserting (fig.4.7) Fig. 4-6 Fig. 4-7 7. Slide the holder rods into the adjacent holes of the assembly in accordance with Fig. 4-8. Using pin
ページ10に含まれる内容の要旨
RET Series 8. Screw the wastecatcher square bars into the previously inserted wastecatcher holder rods, (Fig. 4-10) putting the supplied screws through the largest drilling in the square bar, so that the head of the screw sits flush within the bar itself. (Fig. 4-11) Fig. 4-10 Fig. 4-11 9. Position the main trimmer assembly on top of the floor stand. And properly align the bolt holes. Use bolts (M8x55) to attach the main trimmer assembly to the floor stand. (Fig. 4-12) Fig. 4-12 10. P
ページ11に含まれる内容の要旨
RET Series 5. OPERATION The trimmer must only be used by trained and qualified personnel. The trimmer must be used only for trimming material for which it has been designed. For recommended maximum cutting thickness see page 16. 1. The trimmer should be positioned on a level surface in an area with adequate lighting and enough work space for feeding materials. Connect the power cord to the AC outlet and turn the Power switch to the ON position. The machine should be operated from the f
ページ12に含まれる内容の要旨
RET Series 6. MAINTENANCE Standard maintenance CAUTION: Unplug the trimmer from the power outlet during any maintenance to avoid risk of electric shocks. Note: Only qualified personnel should attempt standard maintenance on the trimmer. If needed, wear gloves and use a damp cloth (alcohol) and rubber gum eraser to remove any adhesive on the cutting blade. Maintenance Procedures Follow below procedures as needed. Frequency of Maintenance Procedure Precautions execution General dusting
ページ13に含まれる内容の要旨
RET Series 7. TROUBLESHOOTING Symptoms Cause Possible Solution a. Plug the power cord into a. Power cord not plugged in appropriate position Machine won't turn on. Lamp b. P ower switch is in “0” off is off, and main switch is off b. Put power switch back position position “1” on position c. P ower fuse is blown out c. Replace main power fuse a. If the 'led3' on the PCB is off, the fuse on the PCB is blown out a. Replace the fuse on PCB Thought power & lamp is 'ON', but cutter won't m
ページ14に含まれる内容の要旨
RET Series 8. SPECIFICATIONS 9.1 Technical information MODEL RET-1500 RET-2000 RET-2500 Power supply 100V(50/60Hz), 110~120V(60Hz), 220V(60Hz), 220~240V(50Hz) Absorbed current max 0.8A -(max 1.5A) Max cutting thickness 30mil Usable cutting length 59inch 78inch 98inch Cutting speed 6.6ft/sec Length 77.6inch 99.2inch 116.9inch Width 19.9inch Height 40.2inch Working table height 34.3inch Unit weight 106lbs 131lbs 155lbs Accessories Roll Feeder 9.2 Recommended Trimming Materials NO Material Type
ページ15に含まれる内容の要旨
RET Series 9. WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One (1) year for Parts and Labor from the date of installation, excluding cutting blades which are warranted for Six (6) months. This warranty is valid only to the original purchaser. This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended. Royal Sovereign’s sole and exclusive liability and the c
