ページ1に含まれる内容の要旨
®
OWNER’S
MANUAL
MD
Model No.
139.18847
139.18857
®
The Chamberlain Group, Inc.
GARAGE DOOR OPENER
Cover - SEARS
4/16/92
1/2 HP
For Residential Use
Only
MD
n Safety Precautions
Caution:
n Assembly
Read and follow all
n Installation
safety rules and
n Adjustment
operating instructions
n Care and Maintenance
before first use of this
n Operation
product.
n Troubleshooting
Fasten the manual
n Parts List
near the garage door
after installation.
®
Sears Canada, Inc., Toronto, Ontario M5B 2B8
ページ2に含まれる内容の要旨
Contents Page Contents Page A review of safety alert symbols.................................2 Install the lights and lenses ......................................19 You'll need tools..........................................................3 Attach emergency release rope and handle ...........19 Safety information regarding garage door Electrical requirements.............................................20 locks and ropes.........................................................3 Safety revers
ページ3に含まれる内容の要旨
1 1 You'll Need Tools During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below. Pencil Carpenter's
Hack Saw Level Tape Measure Wire Cutters WARNING WARNING Claw Hammer Drill 3/16", 5/16", and
Pliers 5/32" Drill Bits Stepladder Screwdriver Adjustable End Wrench 1/2" and 7/16" Sockets
and Wrench WARNING WARNING CAUTION An unbalanced garage door might not reverse To avoid damage to the garage door and when required and someone under the do
ページ4に含まれる内容の要旨
— — — — — — — — — — — — — — — — FINISHED CEILING Support bracket &
SECTIONAL Door Installation fastening hardware
is required.
Horizontal and vertical reinforcement
Before you begin, survey your garage area to see whether any of the conditions below apply to your installation. See page 17. is needed for lightweight garage doors
Slack in Chain Tension
(fiberglass, steel, aluminum, door with glass panels, etc.).
is Normal When
See page 24 for details. Gara
ページ5に含まれる内容の要旨
Slack in Chain Tension
is Normal When
Garage Door is Closed One-Piece Door without Track ONE-PIECE Door Installation Before you begin, survey your garage area to see FINISHED CEILING
whether any of the conditions below apply to your Support bracket
& fastening hardware
installation. may be required.
See page 17. Header
Wall Closed Position Cable
Pulley Bracket Trolley Access Door Cable Header
Bracket T-rail The Chamberlain Group, Inc.
Door Bracket
Emergency
One-Piece Door with Tra
ページ6に含まれる内容の要旨
Opener Carton Inventory Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and installation is shown on page 7. Security✚ Cable
Three-Function Remote Control
with Visor Clip (2) Pulley Bracket Standard Control Console Trolley
2-Conductor
Bell Wire
White & White/Red T-Rail
Center Section Header Bracket T-Rail
End Sections Ligh
ページ7に含まれる内容の要旨
NOTICE Group all hardware found in all packages contained in the rail and opener cartons into the three kits illustrated below. Assembly Hardware Kit 41A3534 Hex Screw
Nut
Washered Screw
Carriage Bolts
5/16"-18x7/8" (3)
5/16"-18 (5) 5/16"-18x1/2" (2)
Master Link (2) 1/4"-20x1/2" (4) (mounted in opener) Lock Nut
Trolley
Lock Washer
1/4"-20x7/16" (4) Threaded Shaft (1) 5/16" (4) Installation Hardware Kit 41A3475-4 Lag Screw
Rail Grease 5/16"-9x1-5/8" (2) Hex Screw
5/16"-18x7/8" (4
ページ8に含まれる内容の要旨
Assemble Tee Rail & attach Cable Pulley Bracket
Assembly Section: Pages 8 – 11 SEARS '92 (525)
To avoid installation difficulties, do not run the garage door opener until instructed to do Assemble Tee Rail & attach Cable Pulley Bracket
so. Assemble Tee Rail & attach Cable Pulley Bracket
4/16/89 - 6/27/89 - 3/9/92 - 4/13/92 SEARS '92 (525)
SEARS '92 (525)
Make sure bolt necks are 4/16/89 - 6/27/89 - 3/9/92 - 4/13/92 4/16/89 - 6/27/89 - 3/9/92 - 4/13/92 Assembly Step 1 seated in the squa
ページ9に含まれる内容の要旨
The Chamberlain Group, Inc.
Step 2 Install Trolley & Attach Chain Retainer Bracket
The Chamberlain Group, Inc.
Hardware Shown Sears Chassis
Assembly Step 2 Actual Size Step 2 Install Trolley & Attach Chain Retainer Bracket
4/12/92
Install the Trolley on the T-rail Sears Chassis
4/12/92
• Attach the threaded shaft to the trolley with the Trolley lock washer and nuts as shown. Lock Washer Nut Rondelle-frein Écrou de 5/16" 5/16"-18 de 5/16 de po 5/16 de po-18 Trolley Lock Washer
5/16" O
ページ10に含まれる内容の要旨
Assembly Step 4 The Chamberlain Group, Inc.
WARNING WARNING Step 4 Install Chain & Cable - Sears Chassis
Install the Chain/Cable & The Chamberlain Group, Inc.
Attach the Sprocket Cover Serious injury can result if fingers become Opener
4/10/92 Sprocket entangled in moving opener sprocket. Attach Step 4 Install Chain & Cable - Sears Chassis
The Chamberlain Group, Inc.
sprocket cover securely. Never operate opener Opener
4/10/92 Step 4 Install Chain & Cable - Sears Chassis
Dispensing
ページ11に含まれる内容の要旨
Step 5 Tighten Chain Sears 315-699 Disk 1 (Yellow) Models 53315, 534153, 53615, 53625 & 53699 Rondelle- frein 1/18/89 - 2/9/89 - 4/16/89 - 6/6/89 - 6/27/89 - 12/18/89 - 1/15/92 Écrou extérieur Écrou intérieur Pour visser l'écrou extérieur Pour visser l'écrou intérieur Chariot Chaîne 1/2 pouce Assembly Step 5 Patin du rail Tighten the Chain & Cable Lock Inner Nut Outer Nut Washer • Spin the inner nut and lock washer down the threaded shaft, away from the trolley. To Tighten Outer Nut • To tigh
ページ12に含まれる内容の要旨
Installation Section: Pages 12 – 27 The Chamberlain Group, Inc.
The Chamberlain Group, Inc.
Position Header Bracket
SECTIONAL DOOR AND
Position Header Bracket
SECTIONAL DOOR AND
Installation Step 1 The Chamberlain Group, Inc.
WARNING WARNING Sectional and One-Piece Track Installations
Sectional and One-Piece Track Installations
ONE-PIECE DOOR WITH TRACK ONE-PIECE DOOR WITH TRACK Position Header Bracket
Determine Header Bracket Location SECTIONAL DOOR AND
1/30/92 - 4/6/92 1/30/92 -
ページ13に含まれる内容の要旨
The Chamberlain Group, Inc. The Chamberlain Group, Inc. Position Header Bracket Position Header Bracket One Piece Door Without Track One Piece Door Without Track 1/30/92 - 4/7/92 1/30/92 - 4/7/92 The Chamberlain Group, Inc. Position Header Bracket Unfinished Unfinished One Piece Door Without Track Header Wall Header Wall Ceiling Ceiling Vertical Vertical 1/30/92 - 4/7/92 Centerline Centerline ONE-PIECE Door Without T 2x4 rack 2x4 Structural Structural supports supports Read the Safety inst
ページ14に含まれる内容の要旨
You can attach the header bracket either to the Installation Step 2 wall above the garage door, or to the ceiling. Mounting New Header Bracket
Follow the instructions which will work best for Install the Header Bracket 10/16/91 - 10/26/91 - 4/5/92 your particular requirements. Mounting Header Bracket to WALL Mounting New Header Bracket
Fasten the Header Bracket to the Wall Mounting New Header Bracket
10/16/91 - 10/26/91 - 4/5/92 • Center the bracket on the vertical guideline with • Mark ei
ページ15に含まれる内容の要旨
The Chamberlain Group, Inc.
Attach Tee Rail to Header Bracket
2/4/92 - 4/9/92 Installation Step 3 Attach the T-rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. Header Wall If the door spring is in the way you'll need help. Header
Bracket Have someone hold the opener securely on a temporary support to allow the T-rail to clear the Cable
spring. Pulley
Bracket • Position the cable pulley bracket agains
ページ16に含まれる内容の要旨
NOTICE Step 2 Attach Tee Rail to Header Bracket - Sears 315-699 (Yellow Disk #2)
Models 53315, 53415, 53515, 53625 & 53699
6/20/89 - 6/27/89 - 11/6/89 WARNING WARNING Rail 2x4 à plat Support de linteau Dessus de l'ouvre-porte Dessus de la porte
Porte Installation Step 4 CAUTION Manual Disconnect and Lockout
Position the Opener Escabeau Escabeau Sears -92
To prevent damage to steel, aluminum, Follow instructions which apply to your door fiberglass or glass panel doors, do not rest the typ
ページ17に含まれる内容の要旨
Step 4 Hang Opener
Sears '92 Front to Back
3/26/92 Step 4 Hang Opener
Sears '92 Front to Back
3/26/92 Solives Installation Step 5 WARNING WARNING Hang the Opener Tire-fond de
The opener could fall and injure someone if it 5/16 de po-18 x 1-7/8 de po Solives is not properly secured. Fasten the opener Mesurer
securely to structural supports of the garage. la distance Tire-fond de
Two representative installations are shown. Structural
5/16 de po-18 x 1-7/8 de po Supports Yours may be
ページ18に含まれる内容の要旨
WARNING WARNING CAUTION Installation Step 6 WARNING Install the Door Control Do not connect to live electrical wiring. Connect only to 24 Volt low voltage wires. Connection to live wires or higher voltage may cause serious Locate the door control within sight of the door injury from shock, burn or electrocution. at a minimum height of 5 feet where small Children operating or playing with a garage children cannot reach, and away from all moving door opener can injure themselves or others. pa
ページ19に含まれる内容の要旨
NOTICE NOTICE 6. Attach the User Safety Instruction label to the wall Do NOT connect the power and operate the near the door control, and the Maintenance opener at this time. The trolley will travel to the Instruction label in a prominent location on the full open position but will not return to the inside of the garage door. close position until the sensor beam is connected and properly aligned. Page 32 explains how to use the door control. See Safety Reversing Sensor instructions beginning
ページ20に含まれる内容の要旨
Installation Step 9 WARNING WARNING Electrical Requirements To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third Do NOT use an extension cord, 2-wire adapter, or change the plug in any way to make it fit grounding pin. This plug will only fit into a grounding your outlet. type outlet. Permanent wiring
If the plug doesn't fi
