ページ1に含まれる内容の要旨
www.chamberlainanz.com
www.chamberlainanz.com
MR850
professional
MR850/MR650
Rolling Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY
ページ2に含まれる内容の要旨
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual. These safety alert symbols mean WARNING : A possible risk to personal safety or property damage exists. Keep garage
ページ3に含まれる内容の要旨
1 2 TOOLS REQUIRED CARTON INVENTORY 1. Instruction manual (this document) 1. Ladder 2. Stop collar 2. Adjustable wrench for U-bolts already installed 3. Clamp bracket on the door 4. Release handle, cord and risk of entrapment card 3. 8mm socket, 10mm socket and 13mm extended socket and socket wrench 5. Transmitters (2) 6. Wireless wall button 4. 300mm socket extension (for minimum side-room 7. Hardware bag installations) 8. Weight bar 5. Drill and 5.5mm drill bit 9. Clamp plate 6. Philips-head s
ページ4に含まれる内容の要旨
4 TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door. • Lift the door to about halfway and then release it. The door should remain spring balanced. • Raise and lower the door to determine if there are any sticking or binding points. • If your door does not hold in place or the door binds or sticks, call a qualified door technician before installing the opener. 5 INST
ページ5に含まれる内容の要旨
click THE RELEASE HANDLE & CORD 7 www.chamberlainanz.com • Thread one end of the rope through the hole in the top MR850 of the red release handle so that “NOTICE” reads right side up as shown. • Secure with an overhand knot at least 25mm from the professional end of the rope to prevent slipping. • Thread the other end of the rope through the loop of Limit (up) Learn (down) the manual release cable. button button • Adjust rope length so the handle (when installed) will Start / Stop be no higher t
ページ6に含まれる内容の要旨
10 ATTACHING EXTENSION POLES (IF REQUIRED) Optional accessory not provided • Align the extension pole holes with the drive legs. • Insert the extension poles into the drive leg and fix in place using screws provided. • Slide the reinforcing brace over the poles and fix in place using the screws provided. Release cable Rope Manual Release Overhand knot Warning Label Reinforcing brace must be used. Use extension pole kit part number 001B6449-1 Release handle 11 LEFT / RIGHT HAND INSTALLATION LEFT
ページ7に含まれる内容の要旨
12 INSTALLATION PROCEDURE Do not allow people to walk under or around the door during the installation process as serious injury can occur. NOTE: The opener can be installed on either side of the door. The following instructions are for Rope RIGHT HAND INSTALLATIONS (as illustrated i.e. inside the garage looking out). For left hand installations, reverse the instruction terminology (eg LEFT for RIGHT etc). Door stand Preparation: • Place the opener in manual release mode (refer section 8). • Ope
ページ8に含まれる内容の要旨
13 SETTING THE LIMITS & RIGHT OR LEFT OPERATION Travel limits set how far your door goes up and down. Your opener must be configured correctly for right or left hand installation to operate correctly, if not the door will rotate in the reverse direction. NOTE: The MR850/MR650 opener is factory configured for right hand installation. The opener will operate during this procedure. Make sure the door is clear of obstruction. Ensure your hands are away from any moving parts before activating the doo
ページ9に含まれる内容の要旨
14 SETTING THE FORCE The force, as measured on the closing edge of the door, professional should not exceed 400N (40kgf). If the closing force is LRN Press twice TM measured to more than 400N, the Protector System (IR FLASHING Beams) must be installed (refer section 17). x 2 orange LED • Press the LRN button twice to place the opener into force adjustment mode. The indicator LED will flash professional Activate quickly. • Press the ACTIVATION button on the front of the opener. The door will trav
ページ10に含まれる内容の要旨
17 INSTALL THE PROTECTOR SYSTEM™ (IR BEAMS) OPTIONAL ACCESSORY NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400N (40kgf). After the opener has been installed and adjusted, the Protector System™ accessory can be installed. Instructions are included with this accessory. IR Beams must be installed The Protector System™ provides an additional to detect a 100mm high measure of safety against a small child or animal obsta
ページ11に含まれる内容の要旨
INSTALLING YOUR CM128 WIRELESS WALL BUTTON 18 Disconnect power to the opener whilst installing this accessory to prevent accidental activation. Locate minimum 1.5m above the floor To install: • Carefully pry open the CM128 and locate the two screws for mounting. • Attach to the wall using the two screws and wall anchors provided if mounting to a plaster wall. If using a recessed wall box do not use anchors. + NOTE: Do not overtighten screws. NOTE: The wall control supplied with your opener shoul
ページ12に含まれる内容の要旨
KEYLESS DEVICE PROGRAMMING 20 (OPTIONAL ACCESSORIES ) 1 p ro fe s s io n a l Activate the opener only when the door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage whilst the door is in motion. Do not allow children to operate push button(s) or 2 transmitter(s). Do not allow children to play near the door. 3 Wireless Keypad C840 Using the “LRN” Button: 1. Press and release the “LRN” button (1) on the opener, the orange LED will light. 2. Within 30
ページ13に含まれる内容の要旨
21 SPECIAL FEATURES (OPTIONAL ACCESSORIES) 1. Solenoid roller door lock (SRDLK01) - (MR850 only) 2. 24VDC power output for external devices - (MR850 only) 3. Voltage free door monitoring output - (MR850 only) TM 4. The Protector System IR Beams - C77 5. Motion detecting control panel - C98 6. Standby Power Unit (battery backup C475) - (MR850 only) 7. Tear out cable entries (O16mm) 8. Flashing light FLA24-2ANZ (door not closed indicator only) - (MR850 only) 1 7 2 7 3 5 4 jumper wire 8 Black 6 Red
ページ14に含まれる内容の要旨
22 SPARE PARTS 041A6811 001A6621 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. 041A6812 041A6813 041D6637 (MR850) 041D6637-1 (MR650) 001A6528 041A6815 (MR850) 041A7282 (MR650) 002B1600 041A6814 (MR850) 041A6778 (MR850) 001B6681 041A7292 (MR650) 041A6778-1 (MR650) 041A6811 Mount plate sub assembly MR850 (including motor) 041A6812 Sungear kit 041A6813 Front upper housing 041A6814 Base housing MR850
ページ15に含まれる内容の要旨
LOCK LIGHT 9. Model 760 Outside keyswitch 23 ACCESSORIES 10. Model CM1702 Outside quick release 1. Model CM128 2 Channel wireless wall button 11. Model C77 The Protector System™ (IR Beams) 2. Model CM844 4 Channel transmitter 12. Model FLA24-2ANZ Flashing light kit - (MR850 only) 3. Model C940 1 Channel transmitter 13. Model C475 Standby Power Unit (battery backup) - 4. Model C943 3 Channel transmitter (MR850 only) 5. Model C945 3 Channel mini transmitter 14. Model SRDLK01 Solenoid roller door l
ページ16に含まれる内容の要旨
DIAGNOSTIC CHART Symptom: One or both of the indicator lights on the IR Beams are not on 1 FLASH steadily. IR Beams wire open • Inspect sensor wires for an electrical short (eg. staple in wire), correct wiring (broken or disconnected). polarity (black/white wires reversed), broken or disconnected wires, replace/attach as needed. • Disconnect all wires from the opener. OR • Remove beams from brackets and shorten sensor wires to 30-60mm (1-2”) from back each of sensor. • Re-attach sending eye to o
ページ17に含まれる内容の要旨
• Repeat the limit and force setting in section 13 &14. TROUBLESHOOTING Repeat safety reverse test after adjustments. 1. The opener will not operate from either the 9. The opener strains to operate door: ACTIVATION button or the transmitters : • The door may be out of balance or the springs may • Does the opener have electric power? Plug a lamp into be broken. Close the door and use the manual the outlet. If it does not work, check the fuse box. release to disconnect the door. Open and close the
ページ18に含まれる内容の要旨
OPERATION OF YOUR OPENER CARE OF YOUR OPENER When properly installed, your opener will operate Your opener can be activated by any of the following with minimal maintenance. The opener does not devices: require additional lubrication. Limit and Force Settings: These settings must be • The ACTIVATION button checked and properly set when the opener is Press the button until door starts to move. installed. Weather conditions may cause some minor changes in the door operation, requiring • The wall c
ページ19に含まれる内容の要旨
CHAMBERLAIN LIMITED WARRANTY Liability – Australia only Merlin Professional MR850/MR650 Under no circumstances shall the Seller be liable for Roller Door Opener consequential, incidental or special damages arising in connection with the use, or inability to use, the Unit. In no Chamberlain Australia Pty Limited / Chamberlain New event shall the Seller's liability for damages or injury arising Zealand Limited (Seller) warrants to the original from breach of law or contract or for negligence, exce
ページ20に含まれる内容の要旨
TM Trademark of The Chamberlain Group, Inc. ® Registered Trademark of The Chamberlain Group, Inc. 114B3630D © 2009 The Chamberlain Group, Inc
