ページ1に含まれる内容の要旨
Wireless Keyless
Entry
Model KEP-IV
Operating Instructions and
Owner’s Manual
Control Garage Door Opener and
HomeSettings Home Controls
System with a secure Personal
Identification code (PIN)
Thank you for purchasing the Wireless Keyless Entry (KEP-IV). The Wireless Keyless entry, uses a state
of the art rolling code radio frequency (RF) transmitter to control compatible peripherals.
Your new Wireless Keyless Entry can open and close your garage door when used with a Wayne-Dalton
® ®
id
ページ2に含まれる内容の要旨
Warning/Glossary Definition of Symbol Glossary Copy – See Replicate. Delete – Erase transmitter or SCENE information from Controller. Also known as Exclude. ® Device – Any item that is connected to a Z-Wave module (for example, lamps). Exclude – Remove a module from the controller. Include – Add a module to the controller. LED – Light emitting diode. ® Module – Any HomeSettings or Z-Wave product that is controlled with a HomeSettings or ® Z-Wave remote controller. A module can be part of mo
ページ3に含まれる内容の要旨
Programming to Opener Quick Sta rt Programming KEP-IV to Opener To program the KEP-IV to an Opener or to PROGRAM PROGRAM change an existing PIN: BUTTON BUTTON 1. With new installations, it is recommended to program the KEP-IV before mounting to wall, otherwise proceed to Step 2. 2. Unit can be programmed with garage door in either up or down position. ® ® IDRIVE TORSION IDRIVE TORQUEMASTER 1 3. Press the transmitter PROGRAM BUTTON on ® ® ® DoorMaster light fixture, idrive
ページ4に含まれる内容の要旨
Mounting Quick Mounting the KEP-IV Sta rt CAUTION: MOUNT THE KEP-IV A MINIMUM OF 5 FEET FROM THE FLOOR TO KEEP IT OUT OF THE REACH OF SMALL CHILDREN. With new installations, the KEP-IV should be programmed before mounting to wall. KEP-IV WIRELESS 1. Choose a convenient location that does not KEYLESS interfere with the normal opening and closing ENTRY operation of the door, such as the door jamb, but is within sight of the door. 2. Two screws are included for proper mounti
ページ5に含まれる内容の要旨
Operation/Battery Replacement Quick Sta rt KEP-IV Operation with Opener To OPEN, CLOSE, START, and STOP your garage door opener: 1. Activate your keypad by pressing the ON/ OFF/RESET button. The keypad will illuminate. 2. Enter the 4 digit PIN (personal identification USE KEYPAD number) for the garage door opener you want TO INPUT to operate. The opener will begin to move the 4 DIGIT PIN door. CODE NOTE: The opener will not move the door 2 if the incorrect PIN is entered
ページ6に含まれる内容の要旨
Programming to Gateway Scene 1 Scene 2 Scene 3 Copy Delete Programming KEP-IV to Wireless Gateway To program a PIN to a Scene button on the Wireless Gateway, WDHA-12R, or to reassign a PIN to a Scene button: 1. Press and Hold the Scene button you wish LEDs to program on the Wireless Gateway, either Scene 1, 2 or 3, until the LED turns off, then immediately release the Scene button (before the LED turns on again.) 1 2. Open the cover of the KEP-IV, then push the CHOOSE 1 ON/OF
ページ7に含まれる内容の要旨
Examples/Patents Examples of KEP-IV / Gateway Use Examples of how your KEP-IV can be used with the Wireless Gateway, WDHA-12R are Examples require the following modules: described below. For further ideas, please visit our website at www.wayne-dalton. X = Number required for your particular com/access. application 1. Deck/Patio/Barbecue Area: Mount the 1 - Wireless Gateway, WDHA-12R KEP-IV in a convenient location and pair it with 1 - Wireless Keypad Entry, KEP-IV the Gateway to control
ページ8に含まれる内容の要旨
Warranty/Compliance Limited Warranty Wireless Keyless Entry Model: KEP-IV Subject to the terms and conditions contained in this Limited Warranty, Wayne-Dalton Corp. (“Manufacturer”) warrants the Wireless Keyless Entry, including electronic components (Batteries are not warranted), which is described at the top of this page, for a period of ONE (1) YEAR from the date of installation against: (i) Any defects in material or workmanship. This Limited Warranty is extended only to the person who
