ページ1に含まれる内容の要旨
www.go-merlin.com
MR850EVO/MR650EVO
Rolling Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY
ページ2に含まれる内容の要旨
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual. These safety alert symbols mean WARNING : A possible risk to personal safety or property damage exists. The opener m
ページ3に含まれる内容の要旨
1 2 TOOLS REQUIRED CARTON INVENTORY 1. Instruction manual (this document) 1. Ladder 2. Stop collar 2. Adjustable wrench for U-bolts already installed 3. Clamp bracket on the door 4. Release handle, cord and risk of entrapment card 3. 8 mm socket, 10 mm socket and 13 mm extended socket and socket wrench 5. Transmitters (2) 6. Wireless wall button 4. 300 mm socket extension (for minimum side-room 7. Hardware bag installations) 8. Weight bar 5. Drill and 5.5 mm drill bit 9. Clamp plate 6. Philips-h
ページ4に含まれる内容の要旨
4 TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door. • Lift the door to about halfway and then release it. The door should remain spring balanced. • Raise and lower the door to determine if there are any sticking or binding points (20 kgf is the absolute maximum allowable to raise or lower the door in any position). • If your door does not hold in place or the door
ページ5に含まれる内容の要旨
click THE RELEASE HANDLE & CORD 7 • Thread one end of the rope through the hole in the top of the red release handle so that “NOTICE” reads right side up as shown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. • Thread the other end of the rope through the loop of Learn Limits the manual release cable. button UP Arrow • Adjust rope length so the handle (when installed) will button be no higher than 1.8 m above the floor. Secure with DOWN Arrow Learn
ページ6に含まれる内容の要旨
10 ATTACHING EXTENSION POLES (IF REQUIRED) Optional accessory not provided • Align the extension pole holes with the drive legs. • Insert the extension poles into the drive leg and fix in place using screws provided. • Slide the reinforcing brace over the poles and fix in place using the screws provided. Release cable Rope Manual Release Overhand knot Warning Label Reinforcing brace must be used. Use extension pole kit part number 001B6449-1 Release handle 11 LEFT / RIGHT HAND INSTALLATION LEFT
ページ7に含まれる内容の要旨
12 INSTALLATION PROCEDURE Do not allow people to walk under or around the door during the installation process as serious injury can occur. NOTE: The opener can be installed on either side of the door. The following instructions are for Rope RIGHT HAND INSTALLATIONS (as illustrated i.e. inside the garage looking out). For left hand installations, reverse the instruction terminology (eg LEFT for RIGHT etc). Door stand Preparation: • Place the opener in manual release mode (refer section 8). • Ope
ページ8に含まれる内容の要旨
13 SETTING THE LIMITS FOR RIGHT OR LEFT HAND OPERATION AND FORCE Travel limits set how far your door goes up and down. Your opener must be configured correctly for right or left hand installation to operate correctly, if not the door will rotate in the reverse direction. NOTE: The MR850EVO/MR650EVO opener is factory configured for right hand installation. The opener will operate during this procedure. Make sure the door is clear of obstruction. Ensure your hands are away from any moving parts be
ページ9に含まれる内容の要旨
14 TESTING THE SAFETY REVERSE SYSTEM The safety reverse system test is important. The garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust the opener may result in serious personal injury from a closing garage door. 40 mm Operate the door in the down direction. The door must reverse upon contact with the obstacle. If the door stops on the obstacle, remove obstacle and repeat 40 mm Test obstacle limit and force setting (refer section 13). Re
ページ10に含まれる内容の要旨
16 INSTALL THE PROTECTOR SYSTEM™ (IR BEAMS) OPTIONAL ACCESSORY NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N (40 kgf). After the opener has been installed and adjusted, the Protector System™ accessory can be installed. IR Beams must be installed Instructions are included with this accessory. to detect a 100 mm high The Protector System™ provides an additional obstacle at any point along measure of safety agains
ページ11に含まれる内容の要旨
INSTALLING YOUR E128M WIRELESS WALL BUTTON 17 Disconnect power to the opener whilst installing this accessory to prevent accidental activation. Locate minimum 1.5 m above the floor To install: • Carefully pry open the E128M and locate the two screws for mounting. • Attach to the wall using the two screws and wall anchors provided if mounting to a plaster wall. If using a recessed wall box do not use anchors. + NOTE: Do not overtighten screws. NOTE: The wall control supplied with your opener shou
ページ12に含まれる内容の要旨
19 KEYLESS DEVICE PROGRAMMING (OPTIONAL ACCESSORIES ) Activate the opener only when the door is in Locate 1 full view, free of obstruction and properly the yellow adjusted. No one should enter or leave garage whilst the door is in motion. Do not learn button allow children to operate push button(s) or transmitter(s). Do not allow children to play 2 Press and release near the door. the yellow learn button Wireless Keypad E840M 3 3 To set the keyless entry PIN: 1.Locate the Yellow Learn button on
ページ13に含まれる内容の要旨
OPERATION OF YOUR OPENER CARE OF YOUR OPENER When properly installed, your opener will operate Your opener can be activated by any of the following with minimal maintenance. The opener does not devices: require additional lubrication. Limit and Force Settings: These settings must be • The ACTIVATION button checked and properly set when the opener is Press the button until door starts to move. installed. Weather conditions may cause some minor changes in the door operation, requiring • The wall c
ページ14に含まれる内容の要旨
20 ACCESSORIES 7. Model CM1702 Outside quick release TM 1. Model E128M 2 Channel wireless wall button 8. Model C77 The Protector System (IR Beams) 2. Model E940M 1 Channel transmitter 9. Model E475M-12 V Standby Power Unit (battery 3. Model E943M 3 Channel transmitter backup) - (MR850 only) 4. Model E945M 3 Channel mini transmitter 10. Model SRDLK01-12 V Solenoid roller door lock - 5. Model E840M Keyless entry system (MR850 only) 6. Model 760 Outside keyswitch 5 4 3 1 2 8 9 6 7 10 21 TYPICAL WIR
ページ15に含まれる内容の要旨
22 SPECIAL FEATURES - Information for Service Personnel (OPTIONAL ACCESSORIES) 1. Solenoid roller door lock (SRDLK01-12 V) - (MR850EVO only) 2. 12 VDC power output for external devices - (MR850EVO only) TM 3. The Protector System IR Beams - C77 4. LCD Motion detecting control - C198 5. Standby Power Unit (battery backup E475-12 V) - (MR850EVO only) 1 2 MR850EVO ONLY 4 3 5 14 12V DC
ページ16に含まれる内容の要旨
23 SPARE PARTS - Information for Service Personnel 041A6811-2 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazard. 001A6621 041A6812 026B0166 041B0655 041D7403 (MR850) 041D7403-1 (MR650) 001A6528 204D0250 (MR850) 204D0251 (MR650) 001B6681 002B1600 041B0641 (MR850) 041A7460 (MR850) 041B0640 (MR850) 041B0641-1 (MR650) 041B0640-1 (MR650) 041A7460-1 (MR650) 041A6811-2 Mount plate sub assembly MR850 (includi
ページ17に含まれる内容の要旨
16 DIAGNOSTIC CHART Your garage door opener is programmed for self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the diagnostic codes. DIAGNOSTIC UP DOWN SYMPTOM POSSIBLE CAUSE POSSIBLE RESOLUTON CODE ARROW ARROW TM TM 1-1 1 FLASH 1 FLASH The garage door opener will The Protector System is not Check the Protector System is not close and the lights will installed, connected, or installed and aligned correctly, flash wires may be cut both LEDs are ON with no obstr
ページ18に含まれる内容の要旨
17 DIAGNOSTIC UP DOWN SYMPTOM POSSIBLE CAUSE POSSIBLE RESOLUTON CODE ARROW ARROW 3-3 3 FLASHES 3 FLASHES The garage door opener fails to Battery LED flashing green, Recharge Battery, contact operate and the battery LED is charging circuit stops and starts service centre constantly flashing green to drain causing battery charging status 4-1 4 FLASHES 1 FLASH Door is closing, stops and Obstruction, binding or sticking Remove obstruction, service door. reverses door 4-2 4 FLASHES 2 FLASHES Obstruct
ページ19に含まれる内容の要旨
TROUBLESHOOTING • Repeat the limit and force setting in section 13. 1. The opener will not operate from either the Repeat safety reverse test after adjustments. ACTIVATION button or the transmitters : 9. The opener strains to operate door: • Does the opener have electric power? Plug a lamp into • The door may be out of balance or the springs may the outlet. If it does not work, check the fuse box. be broken. Close the door and use the manual • Have you disabled all door locks? Review installatio
ページ20に含まれる内容の要旨
CHAMBERLAIN LIMITED WARRANTY This Chamberlain Limited Warranty does not cover any failure of, or defect Merlin Professional MR850EVO/MR650EVO in, the Unit due to: Roller Garage Door Opener 1 non-compliance with the instructions regarding installation, operation, maintenance and testing of the Unit or of any product with which the Unit is Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited ® used; (Chamberlain), the manufacturer of Merlin automatic garage door openers, 2 any attem
