ページ1に含まれる内容の要旨
www.chamberlainanz.com
CR550
Rolling Garage Door Opener
Installation and Operating Instructions
Owners Copy: Please keep these instructions for future reference
This manual contains IMPORTANT SAFETY information
DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY
ページ2に含まれる内容の要旨
START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS WARNING • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the instructions in this manual. These safety alert symbols mean WARNING : A possible risk to personal safety or property damage exists. Keep garage
ページ3に含まれる内容の要旨
1 2 CARTON INVENTORY TOOLS REQUIRED 1. Instruction manual (this document) 1. Ladder 2. Warning and risk of entrapment labels 2. Adjustable wrench for U-bolts already installed 3. Hardware bag on the door 4. Release handle, cord and risk of entrapment card 3. 8mm socket, 10 mm socket and 13 mm extended 5. 3 Channel mini transmitter (2) socket and socket wrench 6. Wall or visor mounted transmitter 4. 300 mm socket extension (for minimum side-room 7. Stop collar installations) 8. Clamp bracket and
ページ4に含まれる内容の要旨
4 TESTING THE DOOR Complete the following test to ensure your door is well balanced, and not sticking or binding: • Disable all locks and remove any ropes connected to the garage door. • Lift the door to about halfway and then release it. The door should remain suspended entirely by its spring. • Raise and lower the door to determine if there are any sticking or binding points (20 kgf is the absolute maximum allowable to raise or lower the door in any position). • If your door does not hold in p
ページ5に含まれる内容の要旨
7 PREPARING THE OPENER Set opener position (left or right hand) For left hand side installations For right hand side installations the wire jumper should be removed. the wire jumper should be in place (factory installed). Extension pole Attaching the extension poles (if required) • Insert the extension poles into the gear. • Align the extension pole holes with the gear holes. • Using the screws provided, secure the extension poles. Reinforcing Brace • Align the holes of the reinforcing brace wit
ページ6に含まれる内容の要旨
9 INSTALLATION STEPS FOR RIGHT HAND INSTALLATIONS • Ensure that the opener position jumper (wire connector) is installed (refer Section 7). • Place the opener in manual release mode (refer Section 11). • Open the roller door fully. For safety, tie a rope around the door (as shown). • Mark the position of the door axle on the right hand door bracket. Ensure that the U-bolt on the left hand (non opener) side of the door is secure. • Carefully remove the U-bolt on the right hand side, checking that
ページ7に含まれる内容の要旨
10 ATTACH THE RELEASE HANDLE AND CORD • Thread one end of the rope through the hole in the top of the red handle so “NOTICE” reads right side up as Release cord shown. • Secure with an overhand knot at least 25 mm from the end of the rope to prevent slipping. Rope • Thread the other end of the rope through the loop of the manual release cable. Manual release • Adjust the rope length so the handle is no higher than Warning label 1.8 m above the floor. Secure with an overhand knot. If Overhand kno
ページ8に含まれる内容の要旨
12 SETTING THE LIMITS Travel limits regulate the points at which the door will stop when moving UP or DOWN. During the set up procedure, the motor will run and operate the door. The opener must be fully installed on the door and all installation steps completed before proceeding. fig 1 The opener will operate during this procedure. Make sure the door is clear of www.chamberlainanz.com obstruction. Ensure your hands are away from CR550 any moving parts before activating the door. PREPARATION: • P
ページ9に含まれる内容の要旨
13 SETTING THE FORCE The force, as measured on the closing edge of the door, should not exceed 400 N (40 kg). If the closing force is TM measured to more than 400 N, The Protector System (IR Beams) must be installed (refer section 16). The force setting regulates the amount of power required to open and close the door. • Door should be closed before proceeding. Press the purple learn button • Press the purple button twice to enter the opener into twice force adjustment mode. The indicator LED wi
ページ10に含まれる内容の要旨
16 INSTALL THE PROTECTOR SYSTEM™ (IR BEAMS) SAFETY FIRST! Whilst Chamberlain have engineered safety features into your garage door opener, we urge you to consider fitting IR Beams to your new garage door opener. In many countries these devices are compulsory to assist in preventing serious injury or property damage. For your own peace of mind and the safety of others please install this inexpensive safety device. NOTE: This accessory must be used for all installations where the closing force as
ページ11に含まれる内容の要旨
17 WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES) NOTE: Your transmitter(s) have already been programmed into your opener. Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage whilst door is in motion. Do not allow children to operate push button(s) or transmitter(s). Do not allow children to play near the door. Fix any wall control at a height of at least 1.5m and within sight of the door but away from any moving parts.
ページ12に含まれる内容の要旨
18 KEYLESS DEVICE PROGRAMMING (OPTIONAL ACCESSORIES ) Activate the opener only when the door is Learn button programming in full view, free of obstruction and properly adjusted. No one should enter or 1 leave garage whilst the door is in motion. Do not Limits Press the purple allow children to operate push button(s) or (learn) button, orange LED will light transmitter(s). Do not allow children to play near the door. 2 Enter 4 digit PIN at Wireless Keypad 8747AML keypad (within 30s) Using the (pu
ページ13に含まれる内容の要旨
LIGHT LIGHT 19 SPECIAL FEATURES 1.Multifunction control panel Connect white/red wire to the red “wired wall 2 1 control” quick connect terminal and the white wire to the white “wired wall control” quick connect terminal. 2.The Protector System™ (IR Beams) Connect both white wires to the white “safety beam” quick connect terminal and both white/black wires to the grey “safety beam” quick connect terminal. 20 ACCESSORIES 4 12 3 5 6 7 1. Model 84330AML 1 channel transmitter 5. Model 760AML Outdoor
ページ14に含まれる内容の要旨
• Clear any ice or snow from the garage floor area where TROUBLESHOOTING the door closes. 1.The opener doesn't operate from either the • Repeat the limit and force setting in section 12 & 13. GREEN start button or the transmitters: Repeat safety reverse test after adjustments (refer • Does the opener have electric power? Plug a lamp into section 14). the outlet. If it doesn't light, check the fuse box. TM • If The Protector System (IR Beams) is installed check • Have you disabled all door locks?
ページ15に含まれる内容の要旨
OPERATION OF YOUR OPENER CARE OF YOUR OPENER Your opener can be activated by any of the following When properly installed, your opener will operate with devices: minimal maintenance. The opener does not require additional lubrication. • The GREEN start button Limit and force settings: These settings must be checked Hold the button down until door starts to move. and properly set when the opener is installed. Weather conditions may cause some minor changes in the door • The wall control, outside
ページ16に含まれる内容の要旨
Chamberlain Limited Warranty, we may, subject to your other rights and CHAMBERLAIN LIMITED WARRANTY remedies as a consumer, charge you a fee to repair, replace and/or Chamberlain CR550 return the Unit to you. Rolling Garage Door Opener Exclusions Chamberlain Australia Pty Limited / Chamberlain New Zealand Limited This Chamberlain Limited Warranty does not cover any failure of, or (Chamberlain), the manufacturer of Chamberlain® automatic garage defect in, the Unit due to: door openers is committe
