ページ1に含まれる内容の要旨
Model L5805
Super Sounds Super Sounds
Super Sounds Super Sounds
S Super Sounds uper Sounds
™
Soccer Soccer
S Soccer occer
Soccer Soccer
www.fisher-price.com
www.fisher-price.com
1
ページ2に含まれる内容の要旨
P PA AR RT TS S PARTS Ball Pin Tube with Tapered End and Target Regular End (Upper) Net 2 Tubes with Tapered Ends (Upper and Lower) 2 Side Tubes Tube with Tapered End and Regular End (Lower) • Please keep this instruction sheet for future reference, as it contains important information. • Adult assembly is required. • Tool needed for assembly: Phillips Screwdriver (not included). M5 x 28 mm Screw M5 Lock Nut • Hand pump (not included) and inflation pin (included) required to inflate the socce
ページ3に含まれる内容の要旨
A AS SS SE EMB MBLLY Y ASSEMBLY CAUTION Rounded Side Long End This product contains small parts in its unassembled state. Adult assembly is required. Tapered End Side Tube Rounded Side Tube with Tapered Ends 2 • Fit the long end of a side tube onto either tapered end of the assembly. Tube with Tapered End and Regular End • Align the holes in the two tubes. Hint: If the holes in the tubes do not align, remove the side tube and place it on the other end of the assembly. • Fit a lock nut, round
ページ4に含まれる内容の要旨
A AS SS SE EMB MBLLY Y ASSEMBLY TOP OF NET Long Sleeve Side Sleeve Side Sleeve Short Sleeve 6 Short Sleeve BOTTOM OF NET Binding 4 • Next, fit the long sleeve and other side sleeve on to the side tube. Note: The short sleeve should not be fitted onto the tube. • Lay the net on a flat surface. • Note the long sleeve, two side sleeves and two short sleeves on the net. - Long sleeve is the top of the net. - Binding is the bottom of the net. Side Sleeves Short Sleeve 7 5 • Locate the side sleev
ページ5に含まれる内容の要旨
A AS SS SEMB EMBL LY Y ASSEMBLY Short Sleeve Short Sleeve Long End of Tube Long End of Tube Short End of Tube 8 Short End of Tube 10 • Fit the long end of either remaining tube through the short sleeve. • Fit the long end of the remaining tube through the short sleeve and weave • Now, weave the tube through the openings on the edge of the net the tube through the openings on the edge of the net. (about half way). Short End of Tube Short End of Tube 11 9 • Fit the short end of the tube into th
ページ6に含まれる内容の要旨
A AS SS SE EMB MBLLY Y ASSEMBLY Rounded Side 14 • Insert the inflation pin into the ball. • Attach the pump (not included) to the pin. 1 • Inflate the ball to a circumference of 15 /2" (39 cm), until firm. Do not over-inflate. • After inflating the ball, remove the pin. Store the pin out of the reach of 12 children for future use. • Fit the ends of the tubes together. Assembly is now complete. • Fit a lock nut, rounded side out, into the hex hole on the inside of the tube assembly. • Insert a s
ページ7に含まれる内容の要旨
B BA AT TT TE ER RY Y I IN NS ST TA ALLA LLAT TIIO ON N B BE EG GINNER INNER BATTERY INSTALLATION BEGINNER Beginner’s score fun sounds when the ball hits the net! Power/Mode Tab Switch Net Battery Compartment Top Edge Door of the Frame Target 1.5V x 3 "AAA" (LR03) • Locate the power/mode switch on the back of the target. Slide the switch to SHOWN ACTUAL SIZE 1 for beginners. • Fit the target onto the top edge of the frame. • Loosen the screws in the battery compartment door and remove the
ページ8に含まれる内容の要旨
PRO PRO C CONS ONSUMER UMER INF INFO OR RM MA AT TIIO ON N PRO CONSUMER INFORMATION Hit the target like a pro for fun sounds! CARE • The frame and net may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do not use harsh or abrasive cleaners. Rinse clean with water to remove residue. Do not immerse this toy. • To prolong the life of the net, store this toy indoors. Tab Power/Mode • Periodically check all fasteners regularly to be sure they are tight. If the
