ページ1に含まれる内容の要旨
CONCRETE VIBRATOR
®
6.5 HP BRIGGS & STRATTON ENGINE
Model 94344
ASSEMBLY AND OPERATING INSTRUCTIONS
Do to continuing improvements, actual product may differ slightly from the product described herein.
WARNING!
Your Warranty Is Voided If:
A. You do not put engine oil in the Engine’s crankcase prior to its first use.
Before each use, check the oil level. Never run the Engine with low or no engine oil.
Running the Engine with low or no oil will permanently
ページ2に含まれる内容の要旨
PRODUCT SPECIFICATIONS Product Compatibility For Use With Harbor Freight Tools’ Model 94345 Concrete Vibrator Head/Hose (Not Included) Engine Type 6.5 HP Briggs & Stratton®Recoil Start Unleaded Gasoline Powered Engine Approval: 2006 CA Emissions Approval 2006 E.P.A. Phase II Regulations Output Coupler 1-7/8” Inside Diameter Shaft Connector 1” Diameter Drive Type Direct Driven Output Vibration Isolators Four Rubber Feet On Frame Overall Dimensions 17-1/2” L x 17-3/4” W x 18-3/4” H Unit Weight 61
ページ3に含まれる内容の要旨
3. Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as chips and sparks. Provide barriers or shields as needed. PERSONAL SAFETY 1. Stay alert. Watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may
ページ4に含まれる内容の要旨
5. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. 6. Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. SERVICE 1. Tool service must be performed only by qualified repair perso
ページ5に含まれる内容の要旨
6. Do not allow children and other unauthorized people to handle or play with the Concrete Vibrator. 7. DANGER! This Concrete Vibrator is designed for outdoor use only. Do not operate the Vibrator in a closed area or in a poorly ventilated area. When running, the Engine (16) of this Vibrator produces carbon monoxide, a colorless, odorless, toxic fume that, when inhaled, can cause serious personal injury or death. Whenever possible, use a carbon monoxide detector (not i
ページ6に含まれる内容の要旨
2. Keep the Concrete Vibrator and surrounding areas clean at all times. 3. When spills of fuel or oil occur, they must be cleaned up immediately. Dispose of fluids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container. 4. Never store fuel or other flammable materials near the Concrete Vibrator. 5. Do not smoke, or allow sparks, flames, or other sources of ignition around the Concrete Vibrator. 6. Keep grounded conduct
ページ7に含まれる内容の要旨
NOISE PRECAUTIONS 1. Prolonged exposure to noise levels above 85 dBA is hazardous to hearing. Always wear hearing protection when operating or working around the Concrete Vibrator when it is running. VIBRATION HAzARD This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an exten
ページ8に含まれる内容の要旨
ASSEMBLY INSTRUCTIONS To Attach The Head And Flexible Hose To The Concrete Vibrator: 1. NOTE: This Concrete Vibrator is designed for use only with the model 94345 Concrete Vibrator Head and Hose (available from Harbor Freight Tools). Do not attempt to use the Concrete Vibrator with any other type of Head and Hose. 2. Turn the Lock Lever (13) up all the way. (See Figure A.) 3. Insert the Cylindrical Plug and Cylindrical Connector of the Head and Hose into the Coupler (2) of the Concre
ページ9に含まれる内容の要旨
4. Turn the Lock Lever (13) downward until it locks the Cylindrical Connector firmly in place. (See Figure B.) CYLINDRICAL CONNECTOR LOCK LEVER (13) FIGURE B PRE-OPERATING INSTRUCTIONS WARNING! Always make sure the Engine’s Power Switch is in its “OFF” position prior to performing any service, maintenance, or cleaning of the Concrete Vibrator. To Add Engine Oil: 1. IMPORTANT! Prior to first using the Concrete Vibrator, the Engine MUST be filled with a high quality 30W grade engi
ページ10に含まれる内容の要旨
To Fill The Fuel Tank: 1. Prior to first using the Concrete Vibrator, the Engine’s Fuel Tank MUST be filled with unleaded gasoline. (See Engine manufacturer’s manual for complete instructions.) 2. To do so, remove the Fuel Tank Cap and fill the Fuel Tank with unleaded gasoline. Then, replace the Fuel Tank Cap. Thereafter, check the Fuel Tank for the amount of unleaded gasoline. When necessary, refill the Fuel Tank. (See Engine manufacturer’s manual for complete instructions.) OPERATING I
ページ11に含まれる内容の要旨
7. When finished using the Concrete Vibrator, remove the Vibrator Head assembly from the concrete. Turn off the Engine (16) of the unit. Disconnect the Vibrator Head and Flexible Hose from the Concrete Vibrator, and use a garden hose to clean the Vibrator Head and Flexible Hose of all concrete and debris. (See Figure C.) 8. Allow the Engine (16) of the Concrete Vibrator to completely cool. Then store the Concrete Vibrator, Vibrator Head, and Flexible Hose in a clean, dry, safe location
ページ12に含まれる内容の要旨
INSPECTION, MAINTENANCE, AND CLEANING 1. DANGER! Make sure the Engine’s Power Switch of the Concrete Vibrator is in its “OFF” position prior to performing any inspection, maintenance, or cleaning of the machine. 2. Before each use, inspect the general condition of the Concrete Vibrator. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect the safe operation of the Concrete Vibrator. If
ページ13に含まれる内容の要旨
PARTS LIST AND ASSEMBLY DIAGRAM Part Description Qty. Part Description Qty. Part Description Qty. 1 Shaft Circlip 1 8 Flexible Washer 4 15 Frame 1 2 Coupler 1 9 Washer 4 16 Engine (B & S 6.5 HP) 1 3 Pin 1 10 Bolt 4 17 Bolt 4 4 Clutch Block 1 11 Elastic Washer 4 18 Spring 4 5 Shaft Connector 1 12 Washer 4 19 Rubber Foot 4 6 Key 1 13 Lock Lever 1 20 Split Pin 4 7 Nut 4 14 Lock Screw 1 21 Connecting Rod 4 NOTE: Some parts are listed and shown for illustration purposes only, and are not available in
ページ14に含まれる内容の要旨
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installati
