ページ1に含まれる内容の要旨
®
ViewSonic
N3290w/N4290p/N4790p
LCD TV
®
ViewSonic
ページ2に含まれる内容の要旨
Contents Important Safety Instructions........................................................................... 1 Copyright Information ...................................................................................... 2 Product Registration........................................................................................ 2 Antenna Installation Instructions ..................................................................... 3 Cleaning the LCD TV ............................
ページ3に含まれる内容の要旨
Important Safety Instructions 1. Read these instructions completely before using the equipment. 2. Keep these instructions in a safe place. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the LCD TV” in this guide for further instructions. 7. Do not block any
ページ4に含まれる内容の要旨
Copyright Information ® Copyright © ViewSonic Corporation, All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product imp
ページ5に含まれる内容の要旨
Antenna Installation Instructions 1. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges, Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to gro
ページ6に含まれる内容の要旨
Cleaning the LCD TV • Make sure the LCD TV is turned off. • Never spray or pour any liquid directly onto the screen or case. To clean the screen: 1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles. 2. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. To clean the case: 1. Use a soft, dry cloth. 2. If still not clean, apply a small amount of
ページ7に含まれる内容の要旨
Getting Started ® Congratulations on your purchase of a ViewSonic LCD TV. Important! Save the original box and all packing material for future shipping needs. Package Contents Your LCD TV package includes: • LCD TV • Remote Control with batteries • Power Cord • RF Cable • Warranty Card* • ViewSonic User Guide Mounting ViewSonic LCD TV to the wall The LCD TV can be used in a free standing position or wall-mounted. Before installing the product to the wall, please
ページ8に含まれる内容の要旨
Place the TV on a solid surface 1. Ensure that the TV is placed in a position to allow free flow of air. Do not cover the ventilation openings on the back cover. 2. Leave at least 15cm around the TV set. Otherwise, air-circulation may be inadequate and cause overheating, which may cause a fire or damage to the TV set. 3. Never place the TV set in hot, oily humid or excessively dusty places. 4. To prevent any unsafe situations, no naked flame sources, such as lighted candles, should be
ページ9に含まれる内容の要旨
Turn the TV on & Off 1. Power On : Press the power button on the remote control or key to pad to turn it on. 2. Power Off : Press the power button on the remote control or key to pad to turn it on. 3. LED Indicator Lights up in blue : the TV is turned on. Lights up in red : the TV is in standby mode. Watching TV 1. Press the TV button on the remote control or press source button to select TV input. 2. Press the MENU button to display the OSD main menu. 3. Press or
ページ10に含まれる内容の要旨
Overview the LCD TV & Connection The Front of the Screen Introduction Power( ): Turn the power on from standby mode or turn the power off return to the standby mode. Source( ): Press this button to display selected source, press button to select input source. Menu( ): Press this button to display or exit the OSD menu. CH/ ( ): When the OSD menu appears, press these two buttons to select the item you want to execute; when no OSD menu appears, use to change channel
ページ11に含まれる内容の要旨
Signal Source Interface from Rear View You can connect numerous items of source equipment to your TV. The figure below shows you how to connect these. Place the TV on a table with the LCD screen facing down to facilitate easy connection with the external equipment. Please take precautionary measures to avoid damaging the LCD screen. (1)Antenna Input: Connect the antenna or CATV cable Note: CATV cable to this 75 coaxial cable input (2)AV1 & S-Video1 Input: Connect th
ページ12に含まれる内容の要旨
2. Digital devices from different manufacturers have the possibility of differing output standards which may cause difficulties for the television to properly display. 3. In case no signal is detected from your HDMI device, turn off the HDMI device and then on again. 4. To get an optimal viewing, it is advised to turn your DVD player to one of the following TV display standards:1280x720p@ 60hz (7)VGA Signal Input: Use the VGA signal cable to connect signals from a PC to the TV Input.
ページ13に含まれる内容の要旨
Signal Source Interface from Side View (8) AV1 & S-Video1 Input: Connect the Video signal or S-Video cable to DVD player, Laser Disc player, videocassette recorder or camcorder (Note: For S-Video, Audio and AV1 are shared). Audio Input: Connect the audio signal source (PC, DVD player, Laser Disc player, videocassette recorder or camcorder) to the audio Input ports. (Note: S-Video2 & AV2 are shared same audio input). Helpful Hints: S-Video shares audio signal with Video
ページ14に含まれる内容の要旨
To Use Remote Control POWER/ Sleep/ Press to turn on/off. With this key you can set a time period after HDMI which the TV should To select HDMI/ PC input. switch itself to standby. Press the key YPbPr/ repeatedly to select the number of minutes. To select component input. The counter runs from 15, 30, 45, 60, 90, 120 Recall/ minutes. To display the previously (PC mode did not TV channel support this function) VOL TV/ Use thi
ページ15に含まれる内容の要旨
Remote Control Battery Installation Follow the steps below to insert batteries. 1. Open the remote control’s rear battery compartment cover. 2. Insert two AAA (1.5v) batteries. Ensure that the positive and negative ends match as indicated on the bottom of the battery compartment. 3. Replace the battery compartment cover. CAUTION 1. Only use the specified AAA batteries. 2. Do not mix new and old batteries. This may result in cracking or leakage, which may pose a risk of f
ページ16に含まれる内容の要旨
OSD function To Use the OSD Menu All the functions for the LCD TV are control either by the remote control or the control button on the front control screen at bottom of right side. 1. Press the Menu button to display or exit the OSD main menu. 2. Use the Up or Down buttons to select the function to be adjusted. The function where the cursor is located is the selected one. 3. Use the Left or Right buttons to enter into the submenu, or to enable or adjust the selected function.
ページ17に含まれる内容の要旨
Picture Setting 1. Picture Mode: User can select User, Drama, DV, Sport & Movie if selected except User item, Contrast, brightness, Saturation, Sharpness, DNR, Backlight can’t adjust. 2. Contrast: Adjust black and white level, suitable contrast can make picture more lightly. Adjustment range is from 0 to 100 3. Brightness: Adjust background brightness, user can collocation it with contrast adjustment range is from 0 to 100. 4. Saturation: Adjust color saturation, range is from 0 t
ページ18に含まれる内容の要旨
Sound Setting 1. Volume: The Volume adjustment range is from 0 to 100, You can adjust the Volume of the picture to the level you prefer 2. Balance: Adjust the balance between left/right channels as required using the left / right buttons. 3. Smart Volume: To select the Automatic Volume Setup. 4. Sound Effect: You can choose your preferred sound effect mode. The selection including Off, News, Movie, Music, Surround, Stereo & User. 5. 100Hz, 300Hz, 1KHz, 3KHz, 10KHz: When you cho
ページ19に含まれる内容の要旨
Setup Setting 1. Language: This indicates the different languages available for the OSD menu, including Chinese, & English. The default is Chinese 2. Wide Mode: To select picture size. Includes 4 modes: Full, 4:3, 16:9, & 16:9 Subtitle. (The options of aspect ratio may be different according to its input source) 3. Sleep Timer: Use this button to set a time period after which the TV will enter into standby mode. The time period can be 0>15>30>45>60>90>120 minutes. The timer will
ページ20に含まれる内容の要旨
Helpful Hints: How to setup Start/Off Timer 1. Time Setup: Sets the current time. Press the “<” or “>” to select adjusting the “Hour”, “Minute” and “Second”, and then press the “” or “ ” key to adjust the required time. And press Exit key to leave the menu. 2. Power On Time: Sets the time for power on. The operation is the same as the Time Setup. 3. Power On Channel: Selects which is the current channel when the TV is powered on. Press the “>” and then press the “” or “ ” key
