ページ1に含まれる内容の要旨
Installation / Troubleshooting Manual
TWINSCAN 3”, GAS AND DIESEL TACH (New LCD)
This manual (part # 1000-158-01) applies to the following product part numbers:
1) 3TB013U
2) 3TB014M
3) 3TB014U
4) 3TB016M
5) 3TB016U
6) 3TB018M
7) 3TB018U
8) 3TB023M
9) 3TB024U
10) 3TB026U
11) 3TB028U
12) 3TS013M
13) 3TS013U
14) 3TS014U
15) 3TS016U
16) 3TS023U
17) 3TS024M
18) 3TS024U
19) 3TS026M
20) 3TS026U
21) 3TS028U
22) 3TW023M
23) 3TW023U
24) 3TW024M
25) 3TW024U
26) 3TW026M
27) 3TW026U
28) 3TW028U
3/8/2000 100
ページ2に含まれる内容の要旨
TROUBLESHOOTING ® TwinScan 3” Instrument - Tachometer (LCD) BEFORE CALLING FOR ASSISTANCE, COMPLETE THESE TROUBLESHOOTING CHECKS AND RECORD YOUR FINDINGS. TECHNICAL SUPPORT REQUIRES THIS INFORMATION BEFORE A RETURN AUTHORIZATION WILL BE ISSUED. IT TAKES ABOUT 20 MINUTES AND IS VERY IMPORTANT IN ANALYZING SYSTEM PROBLEMS. Before starting, record instrument model number and switch settings. MODEL # _____________________ SERIAL # ____________ RED SWITCH POSITION __________ BLACK SWITCH POSITION
ページ3に含まれる内容の要旨
• If 12 VDC is not present, measure between the RED, or RED/WHITE power wire and a known good ground in the instrument panel. If you measure 12 to 14 VDC there may be an instrument ground problem. __________VDC • If 12 to 14 VDC is not present check wiring, switches, fuse, and the 12 VDC power source. III. CONTINUITY TEST • Continuity testing requires access to the back of the Instrument and an Ohmmeter. It verifies that wires are not broken, shorted to ground, another wire,
ページ4に含まれる内容の要旨
INSTALLATION PLANNING ! ! READ ME FIRST - Mechanical & Electrical Installation Planning Saves Time! FloScan systems are not difficult to install. Installing one requires only basic electrical & mechanical skills. With forethought and planning, your system will be installed with few problems. I. Installation Preparation: Review the mechanical installation instructions, then survey your vessel. Determine where the Sensor(s), Pulsation Damper(s), (if used) Switches and Instruments are to be mounted
ページ5に含まれる内容の要旨
VI. Calibration: When system is running properly, refer to the calibration instructions and calibrate your system. USCG approved fuel hose with either fabric or wire reinforcing braid meet the following standards: Hose Marking Permeation Rating 2½ Minute Fire Test USCG Type A-1 100g/m²/24hrs. Required USCG Type A-2 300g/m²/24hrs. Required USCG Type B-1 100g/m²/24hrs. Not Required USCG Type B-2 300g/m²/24hrs. Not Required Table I Installation Do’s & Don’ts Do Don’t Use a Fuel Proof Pipe Thread S
ページ6に含まれる内容の要旨
OPERATION TwinScan 3” Tachometer (LCD) To ensure years of trouble free operation of your new TwinScan instrument, please read all of these instructions carefully before beginning your installation. 1. Mounting Location TwinScan instruments allow you to quickly monitor and compare port and starboard engine performance. The front faces of ® all TwinScan instruments are water-resistant and include a gasket to seal the instrument to the panel. Please note that TwinScan instruments contain magnet
ページ7に含まれる内容の要旨
The number of bars visible in the display indicates how far the engines are out of synch. Referring to the gas engine settings in the chart below, the display shows one vertical line if the engines are within 200 rpm (coarse) or 100 rpm (fine); it will only indicate “IN SYNCH” if the engines are within 100 and 50 for the coarse and fine resolution respectively. Number of bars displayed Coarse (gas) Fine (gas) Coarse (diesel) Fine (diesel) 100 50 50 20 ≡ ≡ |
ページ8に含まれる内容の要旨
INSTALLATION / WIRING ****************************** TwinScan 3” Instrument – Tachometer & GPH *COMBINATION ONLY* Gas– NMEA 0183 Input (LCD) ****************************** This unit conforms to NMEA 183, Version 1.5 and 2.0 interface standards, and requires a message that includes “VTG”, “RMC” or “RMA”. Check your owner’s manual to verify your GPS / LORAN-C includes this information. To insure an easy trouble free installation, read all instructions before starting. WIRING 1. Refer to the elec
ページ9に含まれる内容の要旨
Note: THIS SHEET IS TO BE USED ONLY WHEN INSTALLING A TWINSCAN GPH METER AND TACHOMETER COMBINNED. Back of GPH Instrument Back of Tachometer 0 0 0 0 Black Switch Red Switch Black Switch Red Switch WHITE/ORANGE Data (+) WHITE/RED BLUE GREEN/BLACK MPG SYNC Data (-) * Do not use Back-lit, or Illuminated switches To STARBOARD VIOLET tachometer input YELLOW To PORT BLACK tachometer input RED/WHITE RED 1/2 amp fuse 1/2 amp fuse To Port To Starboard key switch key switch RED/WHITE RED PORT R BLACK B C
ページ10に含まれる内容の要旨
ELECTRICAL Series 5400(0)/5500(0)/56100/5800(0)/6500(0)/6600(0) AccuTroll & CruiseMaster, ® All Multi Function Instruments, & TwinScan SET UP Wire & Switches: Use 18 AWG stranded wire on runs under 50’. For runs over 50’ use 16 AWG. Shielded wire is recommended for all Diesel systems and suggested for Inboard & I/O gasoline systems. Always, “Ground” the wire shield or shield drain wires in the engine room by connecting them to the bonding system or engine block. The double wiring harness for twi
ページ11に含まれる内容の要旨
Tachometer Wiring Information applies only to MFI & TwinScan Instrument Tachometers Tachometer signal wires on MFI & TwinScan Tachometers should be shielded. For proper tachometer operation on gasoline EFI engines, (especially outboards) the engine Ground wire must be physically connected to the MFI or TwinScan instrument ground wire. Note: FloScan recommends using dedicated 18 AWG shielded cable for tachometer signal wire connections. Always, “Ground” wire shields or the shield drain wire in
ページ12に含まれる内容の要旨
ELECTRICAL TwinScan Gas & Diesel Tachometer Tachometer Wiring: For proper tachometer operation on Gasoline EFI engines, (especially outboards) the engine Ground wire must be directly connected to the TwinScan Tachometer ground wire. FloScan recommends using dedicated 18 AWG shielded cable for tachometer signal wire connections. Always, “Ground” wire shield or shield drain wire in the engine room by connecting it to the bonding system, or engine block. CARBURETOR & CLOSED LOOP EFI GASOLINE ENGINE
ページ13に含まれる内容の要旨
WIRING Installation Instructions ® TwinScan 3” Instrument – Tachometer Only Gas and Diesel Engines To ensure years of trouble free operation of your new TwinScan Instrument please read all of these instructions carefully before beginning your installation. CAUTION: To avoid electrical shorts and possible fire, turn OFF the power to the instrument panel until installation is complete. WIRING Use No. 18 AWG multi-strand wire, the included butt splices, and self-sealing heat shrink to make all c
ページ14に含まれる内容の要旨
WIRING SCHEMATIC FOR GAS AND DIESEL TWINSCAN TACHOMETER Wiring Schematic For Gas Twinscan Tachometer Back of Tachometer + 12VDC + 12VDC 0 0 Distributor Distributor Coil Coil Black Switch Red Switch Starboard Keyswitch RED + 12V CABLE + 12V RED/WHITE (Used with TwinScan 1/2 amp fuses GPH instrument ) Port Keyswitch WHITE/ORANGE Tape End GREEN/BLACK Battery Tape End Post BLUE Tape End Negative Wiring Schematic For Diesel Twinscan Tachometer Back of Tachometer PORT STARBOARD Tach Sender Tach Sender
ページ15に含まれる内容の要旨
CALIBRATION TwinScan 3” Instrument – Tachometer (LCD) Back of Instrument Diesel Engines Dial Lamp The TwinScan 3” Tachometer is unique in that it can be calibrated for both gasoline and diesel systems. On the back of the TwinScan 3” Tachometer Instrument, the RED 0 0 Calibration Knobs switch is used for fine calibration. The BLACK switch is used for coarse calibration. Black Switch Red Switch You will use a combination of both switches for proper calibration. Wires DIESEL SYSTEM CALIBRATION Di
ページ16に含まれる内容の要旨
III. ALTERNATOR The alternator input usually comes off one of the windings of the alternator before it is rectified. This tachometer signal is inconsistently inaccurate because of a varying amount of belt slippage depending on the load on the alternator, the dimension of the belt and the belt tension. Calibration You can calibrate the tachometer by two methods: 1. Calibrate to the existing tachometer. Simply rotate the RED and BLACK knobs on the back of the instrument until the two tachometers
ページ17に含まれる内容の要旨
CALIBRATION TwinScan 3” Instrument – Tachometer (LCD) Back of Instrument Gasoline Engines Dial Lamp TwinScan 3” Tachometers are unique in that they can be used on gasoline and diesel 0 0 Calibration Knobs engines. For gasoline engine calibration refer to the appropriate engine section, Inboard or Black Switch Red Switch Outboard. Wires There are two calibration switches on the back of the instrument, Black and Red. Both are required for calibration. If there’s an existing tachometer, or you know
ページ18に含まれる内容の要旨
Outboard Engines: Tachometer calibration for standard point and electronic ignition outboard engines is usually based upon the number of alternator pole pairs. EFI outboards sometimes use a CPU to generate its tachometer signal. Calibration for EFI engines is not always based alternator pole pairs. Refer to your engine manual or check with a local dealer to determine the number of alternator pole pairs your engine has. Standard Points, Electronic Ignition, & EFI Outboard Engines
