ページ1に含まれる内容の要旨
OWNER’S MANUAL
LCD Monitor
P42LHA
1
ページ2に含まれる内容の要旨
Contents Safety Instructions-------------------------------------------------------- 3 Notes and Cautions for Use-------------------------------------------- 9 On usage------------------------------------------------------------------------- 9 On disposal or handing over to a new owner -------------------------- 9 Exemptions---------------------------------------------------------------------- 9 Features--------------------------------------
ページ3に含まれる内容の要旨
Safety Instructions Before using this unit, please read this manual thoroughly to avoid injury and/or damage. Be sure to observe the following instructions, carefully reading each sign and figure listed below: Meaning of Signs Sign Meaning of Sign 1 May cause death or serious injury* . 2 3 May cause injury* or material damage* . 1: “Serious injury” refers to blindness, burns (by both high and low temperature), electrical shocks, poisoning; w
ページ4に含まれる内容の要旨
If water is spilled or objects are dropped inside the unit, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electrical shock. Contact your dealer for inspection. If the unit is dropped or the cabinet is damaged, remove the power plug from the outlet immediately. If the unit is still used in this condition, it may cause a fire or an electrical shock. Contact your dealer for inspection. To turn off the power
ページ5に含まれる内容の要旨
Do not place the unit in an unstable location, such as a shaky table or incline. The unit may fall down and cause injury or damage. Install the unit on a horizontal, stable surface. Do not place the unit in a location subject to vibration. The unit may fall down because of the vibration and may cause an injury. Insert the power plug fully into a 100 240V AC outlet. • If an outlet other than 100 240 V AC is used, it may cause fire or electrical Shock. • Improper insertion of
ページ6に含まれる内容の要旨
Do not insert objects inside the unit. If metallic materials or combustibles such as paper get inside the unit from ventilation holes and other places, it may cause a fire or an electrical shock. Be especially careful that children do not insert objects in the unit. If there is thunder or lightening, do not touch the unit or the power plug. This may cause an electrical shock. Cleaning If dust has collected on the power plug connectors, remove the plug from the outlet and cle
ページ7に含まれる内容の要旨
Do not block the ventilation holes on the unit. The inside of the unit will overheat if the ventilation holes are sealed, which may result a fire. • When installing the unit near a wall, keep the unit at least 10 cm from the wall. • Do not place the unit in a closet or bookshelf where ventilation is poor. • Do not spread a newspaper, tablecloth or curtain over the unit. • Do not place the unit on an unstable surface, such as a rug, or a cushion, etc. • Do not place the unit so that
ページ8に含まれる内容の要旨
Precautions for the remote control battery: Only use the specified battery type. Be sure to insert battery by matching the + and –. Do not recharge, heat, disassemble, short or throw battery into a fire. Do not use the battery beyond their usage period (designated on the battery), do not leave worn out battery in the unit. If these precautions are not observed, it may lead to battery leakage or explosion and may cause burn and injury. If leaked liquid gets into your eyes or gets in to
ページ9に含まれる内容の要旨
Notes and Cautions for Use On usage • Some parts of the display are hot during operation. Please be careful. • In case of moving long-distance, wrap the unit with blanket to avoid damages. Be careful not to bump the unit. • Do not spray on the unit with volatile liquid like insecticide. Do not make contact with rubber or vinyl for a long time. It will damage the coating. On disposal or handing over to a new owner • It is recommended to initialize the unit
ページ10に含まれる内容の要旨
Specifications Model name P42LHA Type 42-inch flat panel LCD display unit Acceptable signals NTSC/PAL/PC Image device 16:9 LCD panel Light source fluorescent back light lamps Resolution 1920 x 1080 dot x RGB 2 Brightness 550cd/m (Typ.) Contrast 1000:1 Response time 12 mS (Typ.) 8 mS (gray to gray) Color temperature 3200K, 5400K, 6500K, 9300K, USER Viewing Angle Horizontal / Vertical: 176 degrees, 85 deg.: (K>=10) Operating temperature 5
ページ11に含まれる内容の要旨
Names and Functions of Controls Front LCD Screen -Power ON-Stand by Indicator -Remote Control Receiver -Light sensor Side Controls No. Key Descriptions 1 Power Power on / Power off 2 Select Activate selection 3 Menu Right 4 Menu Left 5 < Menu Down 6 > Menu Up 7 Exit OSD control Menu button Side Keypad lock/unlock control: Use control push buttons at side: Lock: Press (+) and (<) at the same time and OSD w
ページ12に含まれる内容の要旨
Names and Functions of Controls OSD control Menu button Power on / Power off Menu Right Menu Left Menu Up Menu Down Activate selection One level up Auto adjustment Input source selection Picture in picture PIP picture switch Battery Installation (2) (1) (3) To replace battery insid
ページ13に含まれる内容の要旨
Supplied Accessories Please check all are supplied. Owner’s Manual x 1 Remote Control x 1 VGA Cable x 1(1.8M) OWNER’S MANUAL LCD Monitor P42LHA RS232C Cable x 1(3M) Power Cord x 1 (1.8M) DVI-D Cablex1 (1.8M) RGB to Y-Cb-Cr Cable x 1(1.8M) 13
ページ14に含まれる内容の要旨
Connection VIDEO SIGNAL INPUT/OUTPUT Terminal Type Suitable signals CVBS-IN NTSC/PAL BNC S-VIDEO-IN BNC NTSC/PAL YUV (Y Pb/Cb Pr/Cr)-IN NTSC/PAL BNC CVBS-OUT BNC NTSC/PAL S-VIDEO-OUT BNC NTSC/PAL YUV (Y Pb/Cb Pr/Cr)-OUT BNC NTSC/PAL RGB INPUT/OUTPUT Terminal Type Suitable signals RGB DIGITAL DVI-D 24 pin RGB DIGITAL RGB ANALOG-IN D-Sub 15 pin RGB ANALOG (720p, 1080 i/p) RGB ANALOG-OUT D-Sub 15 pin RGB ANALOG CONTROL INP
ページ15に含まれる内容の要旨
Installation To a service technician For safety, make sure the place has enough strength to hold the whole weight of the monitor and the frames (*1). If necessary, reinforce the place before installation. At least two people are needed for installation. Be careful not to lose removed screws or parts. Before starting installation, discuss well with customers about the position to install, and get their agreement. After installation, check
ページ16に含まれる内容の要旨
Dimension 16
ページ17に含まれる内容の要旨
Power On/Off Before turn on, wire all the cable connecting to auxiliary equipment, power cord, etc. There are two controls for power, Main power switch and POWER (standby / on) button. Main power switch Bottom Front Mode LED indicator Power on Green Power Standby Yellow No signal Orange No power input No LED
ページ18に含まれる内容の要旨
Menu Function Display Menu, pictures or various functions can be set with the buttons on the remote control. The following are summary of Menu Function. For details, please see to refer pages. Function of Remote control No.Key Descriptions No.Key Descriptions OSD control menu 1 Power Power on / Power off 7 Menu button Adjust clock, phase, 2 Auto H position and V 8 Exit One Level up position Automatically Input source 3 So
ページ19に含まれる内容の要旨
Menu display chart MAIN MENU DISPLAY Brightness , Contrast , Hue , Saturation , Flash-Tone Off,Weak,Soft,Strong Black Level , MENU POSITION Zoom In , Out SELECTION Zoom Horizontal Pan Left, Right Zoom Vertical Pan Down,Up Vertical , Horizontal , PIP CONTROL PIP Mode Off, Single, PAP PIP Size Small, Med, Large Vertical , Horizontal , IMAGE Scaling 1:1, Fill, As
ページ20に含まれる内容の要旨
Main Menu page Display Menu page From normal mode, [MENU] button will After entering Main Menu, [ENTER] will display guide to this page. this page. To escape from the mode, use [Exit]. In this Display Menu page, DISPLAY, IMAGE, POSITION, COLOR or PIP CONTROL can be selected. Most of them are picture quality or adjustment related. Once entered to the any mode, such as above right, DISPLAY Menu mode, note th
