ページ1に含まれる内容の要旨
ページ2に含まれる内容の要旨
Table Of Contents User Manual........................................................................................................................... 1 Trademarks and Copyright .................................................................................................... 1 Environmental Issues............................................................................................................. 2 Operator Safety Summary .......................................................
ページ3に含まれる内容の要旨
Table Of Contents 3.12.7 Disconnect Participant......................................................................................... 50 3.12.8 Terminate Meeting .............................................................................................. 50 3.12.9 More about MultiSite (embedded MCU).............................................................. 51 3.13 Control Panel ....................................................................................................
ページ4に含まれる内容の要旨
TANDBERG 1500 MXP 4.6.2 MCU Status Line ................................................................................................... 84 4.6.3 Floor to Full Screen............................................................................................... 84 4.6.4 Web Snapshots ..................................................................................................... 84 4.6.5 MultiSite Picture Mode ..................................................................
ページ5に含まれる内容の要旨
Trademarks and Copyright All rights reserved. This document contains information that is proprietary to TANDBERG. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or by any means, electronically, mechanically, by photocopying, or otherwise, without the prior written permission of TANDBERG. Nationally and internationally recognized trademarks and trade names are the property of their respective holders and are hereby acknowledge
ページ6に含まれる内容の要旨
TANDBERG 1500 MXP Environmental Issues Thank you for buying a product, which contributes to a reduction in pollution, and thereby helps save the environment. Our products reduce the need for travel and transport and thereby reduce pollution. Our products have either none or few consumable parts (chemicals, toner, gas, paper). Our products are low energy consuming products. Battery handling Batteries for the Remote Control are Long Life and Alkaline batteries saving the environment
ページ7に含まれる内容の要旨
User Manual Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions. Equipment Markings The lightning flash symbol within an equilateral triangle is intended to alert the user to the presence of u
ページ8に含まれる内容の要旨
TANDBERG 1500 MXP Lightning - Unplug this apparatus during lightning storms or when unused for long periods of time. ISDN cables - CAUTION - To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel. Damaged Equipment - Unplu
ページ9に含まれる内容の要旨
1 Introduction The TANDBERG 1500 MXP system offers superior audio and video quality in a fully featured unit. MXP stands for Media Experience and indicates the new TANDBERG platform. Main Features: Supports videoconferencing via both IP and ISDN networks. Selection of up to 1,1 Mbps call quality. TF Built-in MultiSite *: A maximum of 4 sites + 3 additional telephone calls can participate in joint meetings. Auto Split, Voice Switched, 4 Split and 3+1 Split pict
ページ10に含まれる内容の要旨
TANDBERG 1500 MXP 1.1 At a Glance Camera The Main Camera is mounted on top of the monitor. The Main Camera includes a high quality color camera with a fast pan/tilt/zoom action. The Main Camera is controlled by the system’s infra-red remote control and operates pan/tilt, focus and zoom. Monitor The monitor displays the far-end and near-end videoconferencing sites in addition to the menus. Codec The Codec is the heart of the system. The main task for the Codec i
ページ11に含まれる内容の要旨
1 Introduction The remote control uses 4 AAA batteries. The system will tell you when batteries are running low. Change batteries from the backside of the remote control. The reach of the remote control signal is 20 meters. For users sitting in an open plan office, this can cause problems. Use the little, white switch placed under the batteries to change the reach of the signal from 20 meters to 2 meters. This will prevent you from unintentionally controlling your neighbor's video system
ページ12に含まれる内容の要旨
TANDBERG 1500 MXP 1.2 Menu Structure The menu structure is divided in two. The Main Menu is available for all users and contains all functionality of the system. The Administrator Menu contains all the settings of the system. Enter Administrator Settings from Main Menu - Control Panel. Making changes to the Administrator Settings will change the behavior of the system. The menu structure for Main Menu and Administrator Settings is shown below. 8
ページ13に含まれる内容の要旨
1 Introduction 9
ページ14に含まれる内容の要旨
2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying communication lines. Avoid using communication equipment (other than a cordless ty
ページ15に含まれる内容の要旨
2 Installation 2.1 Unpacking When unpacking the TANDBERG 1500 MXP, you will find the following items: 11
ページ16に含まれる内容の要旨
TANDBERG 1500 MXP 2.2 Connecting Cables Connect the cables according to the figure below: 12
ページ17に含まれる内容の要旨
2 Installation 2.3 Monitor Configuration Before you start using the system, make sure that your monitor uses your desired language. Also, make sure that surround sound is OFF. How to change the monitor language: 1. Press the menu key on the monitor to bring up the monitor menu. The menu key is the 6.th key from the left. 2. Press arrow key down 7 times to select Language. The arrow key down button is the 2.nd key from the left. 3. Press menu key to select Language. 4. User ar
ページ18に含まれる内容の要旨
ページ19に含まれる内容の要旨
ページ20に含まれる内容の要旨
3 General Use Wake up the system When the system is not in use, it is in standby mode and the screen is black. Wake up the system by picking up the remote control. An incoming call or pressing any key on the remote will also wake up the system. If the system does not respond: Make sure that the system is switched on by using the On/Off switch located at the rear of the Codec. Verify that your monitor is switched on. To switch the monitor on, push the power button on the f
