ページ1に含まれる内容の要旨
SyncMaster OL46B
LCD Display
User Manual
The color and the appearance may differ depending on the
product, and the specifications are subject to change
without prior notice to improve the performance.
ページ2に含まれる内容の要旨
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Note Important to read and under- Prohibited stand at all times Disconnect the plug from the Do not disassemble outlet Ground to prevent an electric Do not
ページ3に含まれる内容の要旨
Safety Instructions • Wipe the monitor using a soft, slightly damp cloth that has been squeezed . Do not use a cleaning agent that contains alcohol or solvents, or that is surface active. Otherwise, the exterior may discolor or crack or the panel coating may come off. Do not spray water or cleaning agent directly onto the monitor. Otherwise, the liquid may sink into the monitor and cause a fire, electric shock, or failure. Clean the exterior of the monitor using a soft cloth dampened with a sm
ページ4に含まれる内容の要旨
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, there
ページ5に含まれる内容の要旨
Safety Instructions Keep heating appliances as far away from the power cord or the prod- uct as possible. • Otherwise, this may result in electric shock or fire. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Install your product in a well ventilated location. Ensure that there is a clearance of more t
ページ6に含まれる内容の要旨
Safety Instructions During a lightning or thunderstorm, power off the product and remove the power cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall a
ページ7に含まれる内容の要旨
Safety Instructions To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. Wh
ページ8に含まれる内容の要旨
Safety Instructions The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not drop any objects onto the product or cause any impact to the product. • Otherwise, this may result
ページ9に含まれる内容の要旨
Introduction Package Contents Note Please make sure the following items are included with your LCD Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User Manual (Not available in some loca- tions)
ページ10に含まれる内容の要旨
Introduction Others Remote Control Batteries (AAA X 2) Brackets link top (Not available in some loca- tions) Brackets link bottom (x 2) Bolts (x 4) Wrench Bolts (x 4) L Wrench (x 2) Sold separately D-Sub Cable DVI Cable LAN Cable DP Cable HDMI Cable RS232C Cable USB Cable RGB to COMPONENT Ca- Stereo Cable ble Network Box Your LCD Display The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the per
ページ11に含まれる内容の要旨
Introduction Front Brightness Sensor Brightness Sensor detects the ambient light intensity so that the picture brightness can automatically be adjusted. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on t
ページ12に含まれる内容の要旨
Introduction RGB/COMPONENT IN (PC/COMPONENT Connection Terminal (Input)) • Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC us- ing the D-SUB cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COM- PONENT cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC us- ing the RGB to BNC cable. DVI IN (PC Video Connection Terminal) Connect the [DVI IN] port on the monitor
ページ13に含まれる内容の要旨
Introduction Connect a DP cable to [DP IN] on the product and DP IN on another devices. AV/COMPONENT AUDIO IN [R-AUDIO-L] Connect the [AV/COMPONENT AUDIO IN [R- AUDIO-L]] port on the monitor to the audio output port on the PC or on the external device using an audio cable. AV IN Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Connect a headphone or an External speaker. HDMI IN 1 • Connect the [HDMI IN 1] termin
ページ14に含まれる内容の要旨
Introduction RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC Program must be installed on the PC. Note Go to Multi Control and select RJ45 MDC as the MDC Connection. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port Connect a serial cable (cross type) to [RS232C] on the product and RS232C on the PC. To use an MDC, the MDC Program must be installed on the P
ページ15に含まれる内容の要旨
Introduction display device not manufactured by Samsung cannot be used.) DP OUT Connect the network box to a display device that supports DP using the DP cable. RS232C (RS232C Serial PORT) Connect to a device that supports serial commu- nication. Connecting a Network Box (sold separately) Power on or off the network box. POWER S/W ON [ │ ] / OFF [O] Turn on or shut off the AC power supply. POWER Connect to the power cord. Button Not available. Air exhaust vent Air intake vent
ページ16に含まれる内容の要旨
Introduction Note • Periodically replace the intake vent filter at the lower part of the product. • Length of the replacement cycle may vary depending on the fine dust concentration (PM-10) in the location of installation. Refer to the table below. • Fine dust (PM-10): Tiny particles that are very thin with a diameter of 10 or less Intake filter replacement cycle according to the dust concentration Dust Con- 70 60 50 40 30 20 10 centration ( ) Replace- 9 months 11 13 16 21 32 64 ment cycle mont
ページ17に含まれる内容の要旨
Introduction SOURCE OFF Number Buttons + VOL - CONTENT (HOME) MagicInfo Lite TOOLS Up-Down Left-Right / Enter buttons RETURN The Color button / The PC/DVI/HDMI/DP se- lection button MagicInfo 3D ( ) / / / ( ) / D.MENU MUTE CH MENU BLANK INFO EXIT LOCK Power on the product. Select a connected source device. SOURCE Power off the product. OFF Enter the password in the OSD menu. Number Buttons Not available. Adjust the volume. + VOL - Not available. CONTENT (HOME) Not available.
ページ18に含まれる内容の要旨
Introduction Not available. TOOLS Up-Down Left-Right button : Move to the upper, lower, left or Up-Down Left-Right / En- right menu, or adjust an option's setting. ter buttons Enter button : Activates a highlighted menu item. Return to the previous menu. RETURN Manually select a connected input source from PC, DVI, The Color button / The PC/ HDMI or DP. DVI/HDMI/DP selection but- ton MagicInfo Quick Launch Button. MagicInfo MagicInfo can only be enabled when a network box(sold sepa- ratel
ページ19に含まれる内容の要旨
Introduction Wrench Bolts (x 4) L Wrench (x 2) Note To install components that are not provided in the package, purchase the components separately. Note • The product can tip over easily. Ensure the product is fastened to the ground. • For the installation locations of the anchors (sold separately) on the ground, refer to the dimensions of the base as shown below. Dimensions of the base Process to fix the product
ページ20に含まれる内容の要旨
Connecting a Network Box Connecting the Power Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics. Connect the power cables inside the product to power input port on the product and power input port on the network box respectively. Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the DP to HDMI cable. Note • A MA
