ページ1に含まれる内容の要旨
Vehicle Rear Observation System
With Integrated Parking Sensors
Model: CAMSBAR
Installation/User Manual
Features:
• 2.5" LCD Color Display
• 2 Ultra Sonic Rear Obstacle Sensors
• On-screen Display Function
• Automatically Displays Image when Vehicle is in Reverse
• Monitor Mounts on Dash or Windshield
• Mounts on the vehicles license plate or directly to the
bumper.
• Heavy Duty Chrome plating for long life.
• Waterproof and dust proof
ページ2に含まれる内容の要旨
TABLE OF CONTENTS Warnings 2 Product Description 3 Packing List 4 Installation Instructions 5 CAMSBAR Installation 5 Monitor Installation 8 Operating the System 9 Testing the System 9 Specifications 10 Maintenance 10 Troubleshooting
ページ3に含まれる内容の要旨
Warnings This product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to your local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox
ページ4に含まれる内容の要旨
Product Description The Vehicle Rear Observation System with Integrated Parking Sensors is designed to assist the driver by providing a clear and wide image of the area behind the vehicle whenever the vehicle is shifted into reverse. The system will also alert you to obstructions that could not normally be seen in your blind zone. Never rely solely on this product to ensure the area is clear of children and/or obstructions. Use your mirrors and look both ways. This product is not intended
ページ5に含まれる内容の要旨
Packing List The model CAMSBAR package consists of the following items: 1. 2.5” LCD Monitor Part # 31052030 2. Chrome Camera / Sensor Bar − 1 qty Part # 31052380 3. 2.5m Power / Video Supply Cable − 1 qty Part # 31052160 4. Hardware Bag Contains: Part # 31052010 a) Straight Bumper Brackets – 2 pieces b) L Shaped Bumper Brackets – 2 pieces c) 4mm x 16mn bolts – 2 qty d) 6mm x 30mm bolts – 2 qty e) 6mm Nuts – 2 qty f) 4mm Nuts – 2 qty g) 6mm Flat Washers – 2 qty h) 4mm Lock Washer
ページ6に含まれる内容の要旨
Installation Instructions READ THIS MANUAL COMPLETELY BEFORE INSTALLATION We have included all of the items needed for most standard installations. However, since all vehicles are different, we recommend that you review your vehicle completely before starting. CAMSBAR Installation Determine the best location on your vehicle. The CAMSBAR may be mounted below the bumper for better coverage if your vehicle does not have a clear path from the license plate or is ob
ページ7に含まれる内容の要旨
Installing the CAMSBAR on the License Plate 1. Remove the rear license plate to determine the best way to run the power wires to the reverse lights. It is important to use the Reverse lights and not the license plate illumination lamp or other lamps. The system is designed to come on when the vehicle is in reverse gear only. Improper installation can cause the system to operate incorrectly or to run at undesired times. NOTE: All vehicles are designed differently. We offer some general i
ページ8に含まれる内容の要旨
4. Continue to run the power harness for the CAMSBAR to the vehicle’s reverse lamp. Locate the reverse lamp in the tail light assembly. Generally, the Positive wire on the reverse lamp will be a colored wire and the Negative wire will be black. Wiring the Power to the Vehicle’s Reverse Lamp 1. Locate the reverse lamp in the tail light assembly. You may be able to access the wires for the lamp from within the trunk, behind a panel, or depending on your vehicle you may have to remove
ページ9に含まれる内容の要旨
Monitor Wiring 1. Using the supplied Monitor Signal Wire, Plug one end into the Power / signal cable from the bar. 2. The monitor signal wire can be routed through the car to your chosen location for the monitor by either removing the trim panels at the foot of the door sill or by tucking the wire behind the trim panels at the roof of the vehicle. 3. Use caution to insure you do not pinch the wire or obstruct any safety devices such as side airbags. If your vehicle has side air bags we
ページ10に含まれる内容の要旨
Operating the System The CAMSBAR Vehicle Rear Observation System with Integrated Parking Sensors operates when the vehicle is shifted into reverse. The color monitor will activate and show you the view from the camera in the rear of the vehicle. In addition, the back up sensor system is designed to send out an ultra sonic signal that detects obstructions behind your vehicle for an average of 6 feet. If an object is located, the system will sound the buzzer. The buzzer will beep slowly,
ページ11に含まれる内容の要旨
Specifications Power Supply DC12V Power Consumption <6W Current Draw <400 mA Operating Temperature Range 0 to 50 Fuse 2 Amps Maintenance Though your system requires little care, you will still need to maintain its condition and performance by following the guidelines below. • Keep your system away from excessive moisture, extreme heat or cold. • Occasionally clean the surface of the CAMSBAR with a soft cloth moistened with water or glass cleaner. • Remove sn
ページ12に含まれる内容の要旨
Troubleshooting Symptoms Solutions 1. Check the wiring and connections The CAMSBAR does not turn 2. Check the fuse in the power harness on after the vehicle is started 3. Check the power connection at the and the vehicle is in reverse reverse lamp Backup sensors keep sounding Clean the Bar with a soft cloth. The Monitor Stays on all the The system is not wired correctly. If the time or runs when the vehicle system continues to operate while not in is not in reverse. reve
ページ13に含まれる内容の要旨
12
ページ14に含まれる内容の要旨
© 2008 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 13
