ページ1に含まれる内容の要旨
INSTRUCTION MANUAL
Outdoor Day/Night Camera
Wide C-CV454D-3 CU
Standard C-CV454D-9 CU
Tele C-CV454D18 CU
Thank you for purchasing TOA Outdoor Day/Night camera: Wide, Standard, or Tele.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
ページ2に含まれる内容の要旨
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................... 3 2. GENERAL DESCRIPTION ............................................................................. 5 3. HANDLING PRECAUTIONS .......................................................................... 5 4. NOMENCLATURE ............................................................................................. 6 5. INSTALLATION AND CONNECTIONS ..............................
ページ3に含まれる内容の要旨
1. SAFETY PRECAUTIONS • Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. • Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. • We also recommend you keep this instruction manual handy for future reference. Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to pre
ページ4に含まれる内容の要旨
Indicates a potentially hazardous situation which, if mishandled, could CAUTION result in moderate or minor personal injury, and/or property damage. • Leave the installation of the unit to your TOA dealer because the installation requires expert experience and skills. The unit may fall off if incorrectly installed, resulting in possible personal injury. • Do not stand or sit on, nor hang down from the unit as this may cause it to fall down or drop, resulting in personal injury and/or property da
ページ5に含まれる内容の要旨
2. GENERAL DESCRIPTION The TOA C-CV454 series are outdoor Day/Night cameras equipped with a 1/3" CCD. A lineup of cameras with three types of lenses, Wide, Standard, and Tele allows accurate monitoring over a wide range from near to distant subjects depending on the installation location. Noise reduction function enables clear image to be viewed in lower noise under poor lighting conditions. It functions as a color camera in the daytime and as a high-sensitivity monochrome camera in darkness, m
ページ6に含まれる内容の要旨
4. NOMENCLATURE [Appearance] 6 7 5 3 2 4 1 [View with sunshade, front cover, and mounting bracket detached] [View with waterproof cap detached] 8 9 10 11 12 13 15 16 OFF ON HEAD F.ADJ FIXING BLC 1/60 1/100 ATW AWB D / N COLOR IRIS LH 17 18 14 ( ) ( ) 1 Vari-focal lens 10 Focus ring fixing screw ( ) ( ) 2 Sunshade 11 Focus ring ( ) ( ) 3 Front cover 12 Zoom ring ( ) ( ) 4 Mounting bracket (accessory) 13 Mode setting switch ( ) ( ) 5 Safety wire mounting hole 14 Iris control ( ) ( ) 6 Sunshade fix
ページ7に含まれる内容の要旨
φ50 mm 5. INSTALLATION AND CONNECTIONS [Ceiling mounting example] [Wall mounting example] Camera mounting bolt M8 or W3/8 Bracket mounting bolt with washer, stainless Safety wire steel (accessory) mounting hole Install the unit only in a location that can structurally support the weight of the unit and the mounting bracket. Doing otherwise may WARNING result in the unit falling down and causing personal injury and/or property damage. Note Install a safety wire as needed. Select the wire consid
ページ8に含まれる内容の要旨
[Example 1: Mounting to a ceiling or wall] [Example 3: Mounting to a ceiling or wall] If only fine adjustment of camera angle is required; Camera mounting bolt M8 or W3/8 Camera mounting bolt M8 or W3/8 [Example 2: Mounting on a wall] Anti-rotation screw If angle which Example 1 can not cover is required; (tapping screw) Note Camera mounting bolt M8 or W3/8 Installing the mounting bracket using only one camera mounting bolt may cause the bracket to rotate or the bolt to come loose. Be sure to se
ページ9に含まれる内容の要旨
2. Install an anchor nut into a ceiling or a wall, then secure the mounting bracket. Anchor nut Anchor nut M8 or W3/8 M8 or W3/8 Ceiling Ceiling Mounting bracket Mounting bracket Anti-rotation screw (tapping screw) Plain washer Plain washer Spring washer Spring washer Camera mounting bolt Camera mounting bolt M8 or W3/8 M8 or W3/8 3. Install the camera unit to the mounting bracket using the supplied insulating spacers and Bracket mounting bolts (with washer, stainless steel). Note Be sure to pos
ページ10に含まれる内容の要旨
4. Connect the connector. Connect the connector of the supplied cable with waterproof cap to the camera unit's video output terminal, then tighten the lock screw of the connector. Notes • To meet the waterproof requirements, insert the connector in place until it will not go any further. • Wrap self-adhesive butyl rubber tape around cable joints in order to prevent rain from soaking in. UL 1095#22 Black/White (non-polar) Connector (waterproof type) Waterproof cap Cable joints Connect to the AC
ページ11に含まれる内容の要旨
6. Connect the camera unit. Connect the camera unit to both the monitor and the power supply as illustrated below. Notes • If the Video output is not terminated at 75 Ω, camera images are not properly displayed. Make sure that the output has been terminated at 75 Ω at the connected monitor or switcher. • The microphone unit cannot be used for the C-CV454 series. Monitor : BNC plug Video input Video output Power supply When operating on 12 VDC, use the external Video output terminal 24 VAC or 1
ページ12に含まれる内容の要旨
6. ADJUSTMENT 1. After completing camera unit installation and connections, remove both the sunshade and front cover. [Removing sunshade] [Removing the front cover] Loosen two sunshade fixing screws. Turn the front cover in the direction indicated by the arrow to remove. Turn the sunshade, Front cover then extract it. 2. Connect the camera’s monitor output terminal to the monitor. Note: The camera will not operate if the monitor output terminal is connected to the camera drive unit. 3. Switch
ページ13に含まれる内容の要旨
HEAD F X NG MON TOR OUT I I I 5. Adjust the camera angle. • Camera's orientation can be adjusted with the camera mounting and bracket mounting bolts loosen. • Adjust the inclination of image so that the projection of the camera faces upward by loosening a camera head fixing screw and turning the camera head. After adjustment completion, retighten the camera head fixing screw. Note Horizontal camera angle cannot be adjusted if the camera unit is installed as shown in [Example 3] on page 8. Cam
ページ14に含まれる内容の要旨
7. After completing all the adjustments, disconnect the cable connected to the monitor output terminal in Step 2. 8. Tighten both the camera mounting and bracket mounting bolts, then replace the front cover. Note: If the front cover is not secured enough, waterproof effect is reduced, causing unit failure. 9. Insert the sunshade from the front side of the camera unit as shown below, then secure it with two sunshade fixing screws. [Ceiling mounting example] Slot to insert the sunshade Sunshade fi
ページ15に含まれる内容の要旨
7. ABOUT MODE SETTING SWITCH Set each switch to the position that provides the best picture reproduction. OFF ON 1: Focus adjustment switch OFF ON F.ADJ F.ADJ 2: Backlight compensation switch BLC 1/60 1/100 BLC ATW AWB D / N COLOR 3: Flickerless switch 1/60 1/100 IRIS ATW AWB 4: ATW/AWB selection switch D / N COLOR LH 5: Mode selection switch Mode Setting Switch (Factory-preset setting) 7.1. Focus adjustment switch: Set to “ON” position when adjusting focus. (This setting provides the same
ページ16に含まれる内容の要旨
7.4. ATW/AWB selection switch: Set the white balance operation. ATW: Set to “OFF” position during normal use. OFF ON The camera's white balance automatically changes as an object's color temperature varies. AWB: Set to “ON” when the difference between the displayed color and actual color is OFF ON annoying. Shoot the white object, then turn the switch ON. The camera operates on the initially set white balance even if an object's color temperature changes. 7.5. Mode selection switch: Set the oper
ページ17に含まれる内容の要旨
8. TROUBLESHOOTING Symptom Possible Cause Remedy No camera image dis- Cables are not correctly connected. Connect the cables correctly. played on the monitor. BNC plugs are not correctly sold- Solder BNC plugs correctly. ered. Camera image is not Camera lens does not focus Focus the lens. clear. properly. Lens is dirty. Remove dirt on the lens. Image black level of the monitor is Adjust the level correctly in accordance not correctly adjusted. with the instruction manual of the monitor. When the
ページ18に含まれる内容の要旨
9. SPECIFICATIONS Model No. C-CV454D-3 (CU) C-CV454D-9 (CU) C-CV454D18 (CU) Power Source 24 V AC, 50/60 Hz or 12 V DC Power 4 W (300 mA, Maximum current: 800 mA) Consumption Image Device 1/3 type IT-CCD Number of 771 (H) x 492 (V), 380,000 pixels Effective Pixels Scanning System 2:1 interlace Scanning Horizontal: 15.734 kHz, Vertical: 59.94 Hz Frequency Monitor Output VBS1.0 V(p-p), 75 Ω, RCA pin jack Video Output VBS1.0 V(p-p), 75 Ω, Water-resistant connector Synchronizing Internal synchronizat
ページ19に含まれる内容の要旨
• Accessories Mounting bracket ..................................................................................... 1 Cable with waterproof cap (2 m) .............................................................. 1 Bracket mounting bolts (with washer, stainless steel) ............................. 2 Insulating spacer ...................................................................................... 2 • Optional products Pole mounting bracket : C-BC450PM 19
ページ20に含まれる内容の要旨
URL: http://www.toa.jp/ 133-22-161-10
