ページ1に含まれる内容の要旨
LCD TV
TFTV-430 USER'S MANUAL
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
www.palsonic.com.au
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
ページ2に含まれる内容の要旨
Contents Safety Precautions ......................... 1 Important Safety Instructions ........................................................... 2 Overview of TV i. Panel Description ......................................................................... 4 ii. Back Panel Description ................................................................ 5 Antenna Connections ...................................................................... 6 Connections i. AV Connections .......................
ページ3に含まれる内容の要旨
Safety Precautions NOTE TO CABLE/TV INSTALLER: CAUTION This equipment has been tested and found to comply with the limits for a Class B digital RISK OF ELECTRICAL SHOCK device, pursuant to Part 15 of the FCC Rules. DO NOT OPEN These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and THE LIGHTNING FLASH WITH u
ページ4に含まれる内容の要旨
Important Safety Instructions 12. Use only with the cart, stand, tripod, bracket, 1. Read These Instructions - All the safety and or table specified by the manufacturer, or sold operating instructions should be read before the with the apparatus. When a cart is used, use product is operated. caution when moving the cart. Apparatus combination to avoid injury from tip-cover. 2. Keep These Instructions - The safety and operating instructions should be retained for future reference. 3. Heed All War
ページ5に含まれる内容の要旨
Important Safety Instructions 17. Power Lines - An outside antenna system should 23. Outdoor Antenna Grounding - If an outside not be located in the vicinity of overhead power antenna or cable system is connected to the lines or other electric light or power circuits, or product, be sure the antenna or cable system is where it can fall into such power lines or circuits. grounded so as to provide some protection against When installing an outside antenna system, voltage surges and built-up static
ページ6に含まれる内容の要旨
Panel Description Overview of TV Press to display the menu of the available viewing sources. Press to display the OSD menu. Press to change the channel. The two buttons also act as direction buttons. Press to adjust volume level. The two buttons also act as direction buttons. Turn on/off the TV. Speakers Speakers Indicator Remote control sensor -4-
ページ7に含まれる内容の要旨
Back Panel Description Overview of TV Headphone Power Input Antenna Jack S-Video or Composite input Progressive input RGB input AV input -5-
ページ8に含まれる内容の要旨
Antenna Connections * For optimum picture quality, adjust antenna direction. Indoor Antenna Connections Typical Wall antenna jack used in apartment buildings, connect the antenna cable as shown below (Please use the correct type of antenna cable according to the type of wall antenna jack). 75 ohm Round Cable Bronze Wire 300 ohm Flat Wire Apartment buildings Antenna Converter Wall Connection Jack *If you have a 75 ohm round cable, insert the bronze wire and then tighten the connection nut. *If yo
ページ9に含まれる内容の要旨
Audio Cable Composite Video Cable S-Video Cable AV Connections (Yellow) (White) (Red) Camcorder Disc Player VCR Notes: You can connect the TV set with Disc player, Camcorder and VCR following the methods below : 1: S-Video Cable + Audio Cable. Please choose "S-Video" when you select the viewing source. 2: Video Cable + Audio Cable. Please choose "AV" when you select the viewing source. -7-
ページ10に含まれる内容の要旨
Audio Cable Component Video Cable Audio Cable Progressive Scan Cable DVD Player Connection (White) (Red) (White) (Red) DVD Player Notes: Please refer to the methods below to connect TV with DVD Component signal: 1. Connect YCbCr Cable and Audio Cable to corresponding Jacks of DVD Please choose the "YCbCr" when you select viewing source. 2. Connect Progress Scan Cable and Audio Cable to the corresponding jacks of DVD. Please choose "YPbPr" when you select viewing source. -8-
ページ11に含まれる内容の要旨
Audio Cable VGA Cable PC Connections Set-top Box Notes: Please refer to the upward method to connect TV with set-top Box or PC. 1. Connect VGA Cable and Audio Cable to the corresponding jack of PC or Set-top Box. Please choose "PC" or "YPbPr" when you select viewing source. -9-
ページ12に含まれる内容の要旨
Remote Control Overview (All Functions Except Teletext) MUTE Power button Display status 1 Numeric buttons One/double/tri-digit select Previous channel Channel list Select different viewing signals Enter OSD setup mode Exit Enter Next/previous channel Volume up/down Sound mode selection Dual sound selection Select image display mode To freeze current image Aspect To set sleep power off time PIP function Play/Pause Rotate Image page up and down Stop Nine pictures Zoom in/out -10-
ページ13に含まれる内容の要旨
Remote Control Overview (Teletext Functions) On Screen Display Power ON/Standby button Sound Off 1 Teletext Page Up Teletext Cancel Teletext Index Teletext Page Down Teletext List/Flof Teletext Display/Mix Teletext Reveal Teletext Store Teletext Size Teletext Hold Teletext Sub-Page -11-
ページ14に含まれる内容の要旨
Remote Control Operation Batteries installation Remote control direction Point the remote control at the remote sensor. Pull the battery cover upward in the direction shown by the arrow and remove it. Insert the batteries with correct polarity. Replace the battery compartment cover. Make sure there are no Don't place the remote control Signal from the remote con- objects between the near a heater or in a damp trol may be disturbed by sun remote control and its place. A strong impact on light or
ページ15に含まれる内容の要旨
Basic Operation Turn On/Off 1. Connect the antenna cable to the antenna input port on TV. 2. Connect the adapter to the power input port on TV. 3. Put the power line plug into the jack of adapter. 4. Plug the power cord into the wall power outlet after connecting the power cord to the adapter. Then the TV will be in standby mode. 5. Press "POWER" button on the remote control to turn on the TV. 6. Select viewing source: Press the " SOURCE" button to display "Select source" menu as follows
ページ16に含まれる内容の要旨
Basic Operation Menu Description If you want to adjust the display settings, please follow the instruction below. Press the "MENU" button to browse the PICTURE MENU, TV MENU,OPTION MENU, PC MENU in turn. Press "EXIT" to quit menu mode. TV TV Picture Option PC Picture Option PC Brightness 64 - + Channel Preset Contrast 59 - + Channel Exchange Colour 25 - + Program 0 Tint 6 - + Skip Channel Off Sharpness Middle (PICTURE MENU) (TV MENU) TV Picture TV Option PC Picture Option PC OSD Set H Position 3
ページ17に含まれる内容の要旨
Picture Menu Menu Operation Display Performance Adjust You can adjust brightness, contrast and colour to meet your favourite picture requirement. TV Picture Option PC Press the "MENU" button to select " Picture" mode. Brightness 64 - + Press " " buttons to select the item you want to adjust. Contrast 59 - + Colour 25 - + Press " " buttons to reach the desired setting. Tint 6 - + Sharpness Middle Press " EXIT" button to quit. Note: 1. In PC and YPbPr modes, only "Brightness/ Contras
ページ18に含まれる内容の要旨
TV Menu Menu Operation Channel Setting --- Auto Searching You can set TV program list with Auto Searching function quickly. TV Press the "MENU" button to select "TV" mode. Press the " " buttons to select "Channel Preset". Channel Preset Press the " " button to enter "Channel Preset". Auto Searching Press the " " buttons to select "Auto Searching". Fine Tune Manual Searching TV SYS B/G Press " " button, the TV will search channels automatically. Auto Searching All channels will
ページ19に含まれる内容の要旨
TV Menu Menu Operation Channel Setting --- Fine Tune - "Fine tune" helps you adjust specific programs image and sound quality. TV Press the "MENU" button to select "TV" mode. Press the " " buttons to select "Channel Preset". Channel Preset Press the " " button to enter "Channel Preset". Auto Searching Press the " " buttons to select "Fine Tune". Fine Tune Manual Searching TV SYS B/G Fine Tuning Select "Fine Tune" and press " " button to enter the item . Press " " buttons
ページ20に含まれる内容の要旨
TV Menu Menu Operation Channel Setting --- TV system switch You can also set program list one by one by "Manual searching" function. TV Press the "MENU" button to select "TV" mode. Press the " " buttons to select "Channel Preset". Press the " " button to enter "Channel Preset". Channel Preset Press the " " buttons to select "Manual Searching". Manual Searching Press the " " button to enter "Manual Searching". Press " " buttons to change frequency band, and press "
