ページ1に含まれる内容の要旨
PlasmaSync Plasma Monitor
User’s Manual
NEC Technologies
ページ2に含まれる内容の要旨
Important Information Precautions Warnings and Safety Precaution Please read this manual carefully before using your NEC The NEC plasma monitor is designed and plasma monitor and keep the manual handy for future manufactured to provide long, trouble-free service. reference. No maintenance other than cleaning is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel CAUTION surface. The plasma display panel consists of fine pictu
ページ3に含まれる内容の要旨
Recommendations to avoid or minimize phosphor burn-in NOTE: When you connect a computer to this monitor, attach Like all phosphor-based display devices and all other gas the supplied ferrite cores. If you do not do this, this plasma displays, plasma monitors can be susceptible to monitor will not conform to mandatory FCC standards. phosphor burn under certain circumstances. Certain Attaching the ferrite cores: operating conditions, such as the continuous display of a Set the ferrite cores on bot
ページ4に含まれる内容の要旨
Précautions Mises en garde et précautions de Veuillez lire ce manuel avec attention avant d’utiliser votre sécurité moniteur PlasmaSync NEC et conserver ce manuel à portée Le moniteur PlasmaSync NEC a été conçu et fabriqué de la main pour une consultation ultérieure. pour une utilisation fiable et durable. Il ne nécessite aucun entretien en dehors du nettoyage. Utiliser un chiffon doux et sec pour nettoyer la surface de l’écran. ATTENTION Ne jamais utiliser de solvant comme l’alcool ou le
ページ5に含まれる内容の要旨
Pour éviter le risque de combustion au phosphore, les REMARQUE: mesures suivantes sont recommandées : Lorsque vous branchez un micro-ordinateur sur ce moniteur, fixez les noyaux en ferrites fournis. Si vous Comme tous les appareils d’affichage à base de phosphore ne le faîtes, le moniteur ne sera pas en conformité avec et tous les autres affichages à gaz plasma, les moniteurs les exigences des standards FCC. Plasmasync peuvent être sujets à la combustion au Fixation des noyaux en ferrite. phosph
ページ6に含まれる内容の要旨
Limited Warranty Plasma Monitors NEC Technologies, Inc. (hereinafter NECTECH) warrants HOW YOU CAN GET WARRANTY SERVICE this product to be free from defects in material and 1. To obtain service on your product, consult the dealer from workmanship under the following terms and, subject to the whom you purchased the product. conditions set forth below, agrees to repair or replace (at 2. Whenever warranty service is required, the original dated NECTECH’s sole option) any part of the enclosed unit
ページ7に含まれる内容の要旨
Contents How to Attach Options to the Plasma Monitor .... 1 OSM Controls ................................................. 18 Menu Operations ................................................... 18 Introduction ..................................................... 2 Picture Settings Menu............................................. 20 Introduction to the PlasmaSync 50MP2 Adjusting the picture ................................................. 20 Plasma Monitor......................................
ページ8に含まれる内容の要旨
How to Attach Options to the Plasma Monitor You can attach your optional mounts or stand to the plasma monitor in one of the following two ways: Drawing A * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the monitor when it was packaged, beneath the screen surface so as not to scratch the screen face. • This device cannot be installed on its own. Be sure to use a stand or original mounting un
ページ9に含まれる内容の要旨
Introduction * You can select RGB source or Component source for Introduction to the PlasmaSync 50MP2 the 5BNC terminal. When selecting an RGB input, the Plasma Monitor source is switched to the RGB input (3); when selecting NEC’s PlasmaSync™ is a seamless blend of cutting-edge a component input, the source is switched to the DVD/ visual technology and sophisticated design. At 50-inches, HD input (2). with a 16:9 aspect ratio, the PlasmaSync 50MP2 certainly makes a big impression. However, at a
ページ10に含まれる内容の要旨
Part Names and Function Front View POWER/STANDBY INPUT SELECT VOLUME POWER/STANDBY VOLUME INPUT SELECT PROCEED DOWN UP LEFT/— RIGHT/+ /EXIT q PROCEED t POWER/STANDBY indicator Sets the On-Screen Menu (OSM) mode and displays When the power is on ............................. Lights green. the main menu. When the power is in the standby mode ... Lights red. w VOLUME DOWN and UP y Power Adjusts the volume. Functions as the CURSOR (/ Turns the monitor’s power on and off. ) buttons in the On-Screen
ページ11に含まれる内容の要旨
Rear View/ Terminal Board VIDEO 1 VIDEO 2 B VIDEO 3 L ( MONO ) VIDEO 1 VIDEO 2 R VIDEO 3 L ( MONO ) Y R Y CB / PB CB / PB CR / PR C L ( MONO ) CR / PR R RGB 1 L ( MONO ) R/CR/PR R G/Y B/CB/PB HD VD ( ) RGB 1 L MONO R D RGB 3 (Digital RGB) R/CR/PR CONTROL LOCK ON / OFF SPEAKERS MUST HAVE MORE THAN 7WATT RATING REMOTE G/Y IMPEDANCE 6 OHM CONTROL RIGHT LEFT EXTERNAL CONTROL B/CB/PB E AC-IN HD VD L ( MONO ) J K R SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM RIG
ページ12に含まれる内容の要旨
Remote Control w RGB/PC Press this button to select RGB/PC as the source. → RGB/PC1 → RGB/PC2 → RGB/PC3 RGB/PC can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is pressed: → VIDEO1 → VIDEO2→ VIDEO3→ DVD/HD RGB/PC3 ← RGB/PC2 ← RGB/PC1 ← e DVD / HD Press this button to select DVD/HD as the source. DVD/HD can also be selected using the INPUT SELECT button on the monitor. The input switches as follows each time the button is p
ページ13に含まれる内容の要旨
!3 DISPLAY Battery Installation and Replacement Displays the source settings on the screen. Insert the 2 “AAA” batteries, making sure to set them in with the proper polarity. !4 OFF TIMER Activates the off timer for the unit. 1.Press and open the cover. !5 MULTI Press this button to select a screen mode from among single mode, side by side, and picture in picture. !6 SELECT Press this button to select the active picture in a multi screen mode. !7 AUTO ADJUST Press this button to adjust Fine Pict
ページ14に含まれる内容の要旨
Using the wired remote control mode Operating Range Connect the supplied remote cable to the remote control’s * Use the remote control within a distance of about 7 m/ remote jack and the “REMOTE CONTROL” terminal on 23ft. from the front of the monitor’s remote control sensor the monitor. and at horizontal and vertical angles of up to approximately When the cable is connected, the mode automatically 30°. switches to wired remote control. When the wired remote * The remote control operation may no
ページ15に含まれる内容の要旨
Installation VCR or Laser Disc Player To video inputs on the plasma monitor VIDEO 1 VIDEO 2 VIDEO 3 Document Camera L ( MONO ) R Y CB / PB IBM VGA or Compatibles CR / PR L ( MONO ) R RGB 1 Macintosh or Compatibles (Desk top type) R/CR/PR G/Y B/CB/PB HD VD Monitor adapter for ( ) Macintosh L MONO R Signal cable (supplied) To Mini D-Sub 15 pin connector on the plasma monitor RGB 3 (Digital RGB) CONTROL LOCK ON / OFF REMOTE An image may not be displayed CONTROL correctly if a vide
ページ16に含まれる内容の要旨
Connecting Your PC or Macintosh Computer Connecting Your Document Camera Connecting your PC or Macintosh computer to your plasma You can connect your plasma monitor to a document monitor will enable you to display your computer’s screen camera. To do so, simply: image for an impressive presentation. The plasma monitor 1. Turn off the power to your plasma monitor and supports the signals described on page 55. document camera. To connect a PC, Macintosh or compatible graphics adapter, 2. Use a sta
ページ17に含まれる内容の要旨
External Speaker Connections VIDEO 1 VIDEO 2 VIDEO 3 L ( MONO ) R Y CB / PB CR / PR L ( MONO ) RIGHT LEFT R RGB 1 R/CR/PR G/Y B/CB/PB HD VD L ( MONO ) R RGB 3 ( ) Digital RGB CONTROL LOCK ON / OFF SPEAKERS MUST HAVE MORE THAN REMOTE 7WATT RATING CONTROL IMPEDANCE 6 OHM RIGHT LEFT EXTERNAL CONTROL AC-IN External speakers (option) may be connected to the plasma To connect external speakers directly to the plasma monitor to reproduce sound from VIDEO, DVD or RGB monitor: signal source
ページ18に含まれる内容の要旨
Pin Assignments and Signal Levels for 15 pin RGB (Analog) Pin No. Signal (Analog) 5 4 3 2 1 1 Red 10 9 8 7 6 2 Green or sync-on-green 15 14 13 12 11 3 Blue 4 No connection 5 Ground 6 Red ground 7 Green ground 8 Blue ground 9 No connection 10 Sync signal ground 11 No connection 12 Bi-directional DATA (SDA) 13 Horizontal sync or Composite sync 14 Vertical sync 15 Data clock Pin Configuration and Signal of the RGB 3 IN Connector (DVI Connector) The unit is equipped with a type of connector commonly
ページ19に含まれる内容の要旨
Basic Operations POWER DIGITAL ZOOM To turn the unit ON and OFF: Digital zoom specifies the picture position and enlarges the picture. 1. Plug the power cord into an active AC power outlet. 1. Press the POINTER button to display the pointer. ( ) 2. Press the POWER ON button (on the remote control) to turn on the unit. To change the size of the picture: Press the ZOOM+ button and enlarge the picture. The monitor’s POWER/STANDBY indicator will light The pointer will change to resemble a magnifyin
ページ20に含まれる内容の要旨
To cancel the off timer: OFF TIMER To set the off timer: 1. Press the OFF TIMER button twice in a row. The off timer can be set to turn the power off after 30, 60, 2. The off timer is canceled. 90 or 120 minutes. 1. Press the OFF TIMER button to start the timer at 30 OFF TIMER 0 minutes. 2. Press the OFF TIMER button to the desired time. 3. The timer starts when the menu turns off. → 30 → 60 → 90 → 120 → 0 OFF TIMER 30 Note: After the power is turned off with the off timer ... A slight current
