ページ1に含まれる内容の要旨
USER’S
MANUAL
PPC-7508F
Intel® Celeron M
8.4” Panel PC System
PPC-7508F M1
ページ2に含まれる内容の要旨
Copyright Notice PPC-7508F Panel PC System With LCD / Touch screen OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist users in installing and setting up the system. The information contained in this document is subject to change without prior any notice. This manual is copyrighted April, 2007. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording. ACKNOWLEDGEM
ページ3に含まれる内容の要旨
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interfer
ページ4に含まれる内容の要旨
Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION 1-1 About This Manual ....................................................... 1-2 1-2 Case Illustration ............................................................. 1-3 1-3 System Specification ..................................................... 1-4 1-4 Safety and Notification ................................................... 1-9 CHAPTER 2 SYSTEM CONFIGURATION 2-1 Jumper & Connector Quick
ページ5に含まれる内容の要旨
Contents 2-31 Inverter Connector …………………………………… 2-31 2-32 Power Module ………………………………..………. 2-32 2-33 Compact Flash Connector …………………………….. 2-33 2-34 PC 104+ Connector ……………………………………. 2-34 2-35 CPU Fan Connector …………………………………… 2-35 2-36 System Fan Connector ………………………………… 2-35 2-37 Serial ATA Connector ………………………………… 2-35 2-38 Reset & Speaker Connector …………………………. 2-36 CHAPTER 3 SOFTWARE UTILITIES 3-1 Introduction ...................
ページ6に含まれる内容の要旨
Contents APPENDIX A SYSTEM ASSEMBLY Exploded Diagram for CF Card Hook ………..……………… A-2 Exploded Diagram for Fanless Back Cover ….……………..… A-3 Exploded Diagram for System Power Assembly ….……..…. A-4 Exploded Diagram for I/O Port Assembly ………………….. A-5 Exploded Diagram for Motherboard ………………….……... A-6 Exploded Diagram for LCD Assembly ………………………. A-7 Exploded Diagram for System Cable ………………………. A-8 Exploded Diagram for System Inverter Bo
ページ7に含まれる内容の要旨
CHAPTER 1 INTRODUCTION This chapter gives you the information for PPC-7508F. It also outlines the System specifications. Section includes: About This Manual Case Illustration System Specifications Safety precautions Experienced users can skip to chapter 2 on page 2-1 for a Quick Start. Page:1-1
ページ8に含まれる内容の要旨
Chapter 1 Introduction 1-1. ABOUT THIS MANUAL Thank you for purchasing our Panel PC. It is an updated system designed to be comparable with the highest performance of IBM AT personal computers. It provides faster processing speed, greater expandability, and can handle more tasks. This manual is designed to assist you on how to make the proper installation to set up the system. It contains five chapters. The user can use this manual for configuration according to the following ch
ページ9に含まれる内容の要旨
Chapter 1 Introduction 1-2. CASE ILLUSTRATION Page: 1-3 PPC-7508F USER ′S MANUAL
ページ10に含まれる内容の要旨
Chapter 1 Introduction 1-3. SYSTEM SPECIFICATIONS MAINBOARD (PROX-7500) CPU TYPE: Intel Celeron-M ULV 1.0GHz on board (non L2 cache) Auto detect voltage regulator. CHIPSET: Intel 852GM + ICH4 MEMORY : DDR Up to 1GB, 1 x So-DIMM Socket CACHE : Depended on CPU REAL-TIME CLOCK : Embedded in Intel ICH4 South Bridge BIOS : PhoenixAward PnP BIOS 4Mbytes with VGA BIOS KEYBOARD CONNECTOR : Mini DIN connector. Supports PS/2 Keyboard. MOUSE CONNECTOR
ページ11に含まれる内容の要旨
Chapter 1 Introduction DISPLAY : LCD Panel 8.4”: 800*600 SVGA WATCHDOG : Selectable for NMI or Reset function. IDE INTERFACE : 1. One IDE port support up to two IDE device 2. Support Ultra DMA 33/66/100 3. Compact Flash is connected at secondary IDE bus SERIAL PORT : Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte FIFOs. COM1 (D-Sub Connector) for RS-232; COM2 (D-Sub Connector) for RS-232/422/485; COM1/2 contain 5V or 12V power capability wit
ページ12に含まれる内容の要旨
Chapter 1 Introduction HARDWARE MONITORING FUNCTION : Monitor CPU Voltage, CPU Temperature. LED INDICATOR : Power LED. HDD LED. LCD PANEL TFT color LCD is manufactured by using very high brightness technology. Some sequential pixels may not light or may light always, but this is not a failure. LCD TYPE : LCD Panel 8.4”: Priority source - AUO (LVDS) or similar model. PIXEL PITCH : According to the supplier’s LCD specification. BRIGHTNESS : According to
ページ13に含まれる内容の要旨
Chapter 1 Introduction According to the supplier’s LCD specification. BACKLIGHT MTBF : According to the supplier’s LCD specification. DIMENSION : According to the supplier’s LCD specification. TOUCH SCREEN : ELO 8.4” 5W Resistive touch screen (E494781). GENERAL INFORMATION POWER SUPPLY : DC 16V ~ 30V input, ATX 60W output DRIVE BAYS (Optional) : 1x Slim HDD 1x Compact Flash Type-II Slot (IDE, On Board) CONSTRUCTION : Electo Galvanized steel chassis.
ページ14に含まれる内容の要旨
Chapter 1 Introduction 1-4. SAFETY AND NOTIFICATION Following messages are safety reminders on how to protect your systems from damages. And thus, helps you lengthen the life cycle of the system. 1. Check the Line Voltage a. The operating voltage for the power supply should cover the range of DC 16V~30V, otherwise the system may be damaged. 2. Environmental Conditions a. Place your PPC-7508F on a sturdy, level surface. Be sure to allow enough room on each side to have easy a
ページ15に含まれる内容の要旨
CHAPTER SYSTEM 2 CONFIGURATION Helpful information that describes the jumper & connector settings, and component locations. Section includes: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector Pin Assignments Page 2-1
ページ16に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE COM1 RI & Voltage Selection …………..………….... JP6 COM2 RI & Voltage Selection ………………………… JP7 COM3 RI & Voltage Selection ………………………. JP9 COM4 RI & Voltage Selection ………………………… JP8 RS232/422/485 (COM2) Selection ..................…………. JP13 Brightness Voltage Selection ……………………..…….. JP1 LVDS Voltage Selection ………………………………. JP12 LVDS Panel Resolution Selection ……………………… JP10 CMOS Function Selection
ページ17に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-2. COMPONENT LOCATIONS PPC-7508F Connector, Jumper and Component locations Page: 2-3 PPC-7508F USER’S MANUAL
ページ18に含まれる内容の要旨
Chapter 2 Hardware Configuration 2-3. HOW TO SET THE JUMPERS You can configure your board by setting the jumpers. Jumper is consists of two or three metal pins with a plastic base mounted on the card, and by using a small plastic "cap", Also known as the jumper cap (with a metal contact inside), you are able to connect the pins. So you can set-up your hardware configuration by "opening" or "closing" pins. The jumper can be combined into sets that called jumper blocks. When
ページ19に含まれる内容の要旨
Chapter 2 Hardware Configuration JUMPER DIAGRAMS JUMPER SETTINGS Page: 2-5 PPC-7508F USER’S MANUAL
ページ20に含まれる内容の要旨
Chapter 2 Hardware Configuration PPC-7508F Jumper Illustration Page: 2-6 PPC-7508F USER’S MANUAL
