ページ7に含まれる内容の要旨
Connection Options Connection Options Back panel connections Y Pb Pr L AUDIO R 2 1 PC/DVI AUDIO PC VIDEO L AUDIO R VIDEO L AUDIO R PC PC/DVI AUDIO Y / VIDEO Pb Pr L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB Connect a video cable from a computer to this Connect the audio L/R and video cables to your 1 PC Video In 8 AV OUT jack.. other video equipment. PC/DVI Audio Connect the audio L/R cables from a computer 2 In to this jack. Component Connect a component video device to these 3 Video In jacks
ページ8に含まれる内容の要旨
Remote Control Remote Control Battery loading 1. Slide open the cover of the battery compartment on the back of the remote controller. 2. Load two 7# (AAA) alkaline batteries in the compartment, (plus and minus poles to respective mark) 3. Replace the cover of the battery compartment. Precautions Make sure that two AAA alkaline batteries are loaded. As strong light may interfere the signals, change your The batteries must be of the same type. The batteries position to operate the
ページ9に含まれる内容の要旨
Remote Control Function Remote Control Function - The remote control cannot be operated unless the batteries are properly loaded. - When using the remote control, aim it at the remote control sensor on the TV. Function introduction Press this key to start TV from standby mode, press it again to return to standby 1 POWER mode. 2 USB Press this key for quick switching of streaming media. 3 H. LOCK Refer to the Functional Description on Page 20. 4 SOURCE Press this key to open/close signal source
ページ10に含まれる内容の要旨
External Equipment Connections External Equipment Connections Antenna Connection - Antenna or Cable Service without a Cable Box Connections. - For optimum picture quality, adjust antenna direction if needed. Note: * It is recommended that you'd better use 75 coaxial cable to remove the disturbance caused by airwave. * Don't bind antenna cable and electric wire together. To improve picture quality in a poor signal area, purchase and install a signal amplifier. If the antenna needs to be
ページ11に含まれる内容の要旨
External Equipment Connections select the source, press the OK button to confirm. Choose Your Connection There are several ways to connect your television, depending on the components you want to connect External AV Source Setup and the quality of the signal you want to achieve. The following are examples of someways to connect your TV. How to connect Take LE32A300 as an example, Choose the connection which is best for you. • Connect the audio and video cables from the external equipment
ページ12に含まれる内容の要旨
External Equipment Connections program play. / - AUDIO - PC PC/DVI AUDIO Y / VIDEO Pb Pr L R PC IN COMPONENT / AV2 IN DSMB PC PC/DVI AUDIO Y / VIDEO Pb Pr L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB How to use A Turn on the DVD player, insert a DVD. B Use the SOURCE button on the remote control,and PC Setup then press / button to to select COMPONENT mode, press the OK button to confirm. How to connect C Press Play button on external equipment for program play. A Use the TV’s PC IN port
ページ13に含まれる内容の要旨
External Equipment Connections Note ❏ Component, PC, HDMI input sources cannot be used for Monitor out. ❏ When connecting with external audio equipments, such as amplifiers or speakers, please turn the TV speakers off. Power source TO USE AC POWER SOURCE Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard polarized AC PC PC/DVI AUDIO Y / VIDEO Pb Pr L - AUDIO - R PC IN COMPONENT / AV2 IN DSMB outlet. Note ❏ Avoid keeping a fixed image on t
ページ14に含まれる内容の要旨
Basic Receiving and Playing Operations Choose the Input source Basic Receiving and Change the picture source so you can watch your TV, Playing Operations VCR, Cable , or any other devices that are connected to your TV. Playing Operations A Press SOURCE button to enter the Input Source menu and then use / button to select the Switching ON/OFF the TV set desired items (TV, AV1, AV2, Component, PC, HDMI1, In the manual, the OSD (on screen display) may be HDMI2, HDMI3, Multimedia). differ
ページ15に含まれる内容の要旨
Basic Receiving and Playing Operations Palette: How to customize your own picture status Press / to select the Palette option, and then press OK to enter its submenu, and finally press / to select a toner pattern from six patterns A Press MENU button and then use / button to (Cool2, Cool1, Standard, Warm1, Warm2, User) to your select Picture menu. color preference. Normally, the Standard mode is selected. B Press / button to select the desired items., press OK to enter it
ページ16に含まれる内容の要旨
Basic Receiving and Playing Operations • You can also press S.MODE button on the remote The surround sound feature expands the audio control to select the Audio Mode: Standard, listening field wider and deeper to create exceptional sound quality from the TV’s speakers. Music, Movie and User. AVL (Automatic Volume Limit) How to Customize your own sound This will reduces the differences in volume level among broadcasters. status Woofer A Press MENU button and then use / button to To
ページ17に含まれる内容の要旨
Basic Receiving and Playing Operations 1. Use Direct-digit Choosing button to select the number of the channel to be recovered. 2. Do the above steps again. 3. Press to set Skip as Off. / Auto Tuning A Press MENU button and then use / button to select Channel menu. B Press button to select Auto Tuning, then / press OK the menu opens. Manual Search option, and finally Press / to select the Search press /to start manual search. Upon finding a program, the search will auto
ページ18に含まれる内容の要旨
Basic Receiving and Playing Operations • Press / to select the Picture Optimize option. • Press OK to enter the submenu. • Press / to select theDCDI/Color Management to be adjusted, and then press / to select ON or OFF. • Press / to select the DNR to be adjusted, and then press / to select Low/Middle/High/ Off. D After adjusting the current channel and the found to be exchanged to, press / to move the cursor to the Exchange option, and then press OK to start exchange
ページ19に含まれる内容の要旨
Basic Receiving and Playing Operations Clock This is used for adjusting the phase of pixel clock in PC mode. Phase This is used for adjusting H Position and V Position as well as relative parameters in PC modes. Reset Return to factory default settings. Reset Time Menu Press / to select OK or Cancel which with Do you want to reset option values. A Press MENU button and then use / button to select Time menu. Adjust Menu B Press / to select the desired option, press OK to e
ページ20に含まれる内容の要旨
Basic Receiving and Playing Operations the On/Off Time function is enabled while OFF If there is no operation for a few seconds, the display will automatically disappear. indicates the function is disabled. • .After finishing time setting, press OK or MENU to The Lock Set menu is as follows: confirm. Note Lock Set After setting the On/Off Time function, if the TV is AC Change Password OK off off or forcible DC off, the function will be automatically Tuning Lock off cleared. Pre
ページ1に含まれる内容の要旨
OWNER’S MANUAL
LE32A300/LE42A300/LE55A300
LB32R3A/LB42R3A/LB46R3A/LB55R3A
LE32H300/LE42H300/L32K3/L42K3
LED-LCD TELEVISION
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
ページ2に含まれる内容の要旨
Contents Contents Function Menu ...................................................18 Warning 3 Function Menu Set ............................................................ 18 Adjust Menu .......................................................19 Important Safety Instructions 4 Time Menu ..........................................................19 Introduction 6 Lock Setup ..........................................................20 How to use the password function .............................
ページ3に含まれる内容の要旨
Warning Warning WARNING RISK ELECTRIC SHOCK DO NOT OPEN ! WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. * To avoid electric hazards, it is strongly suggested that the back cover not be opened, as there is no any accessory inside the casing. * lf necessary, please contact authorized after-sales services. * A lighting flash mark in a triangle: A potentially hazardous situation, which, if not
ページ4に含まれる内容の要旨
Important Safety Instructions Important Safety Instructions 4 LED -LCD television Owner’s Manual
ページ5に含まれる内容の要旨
Important Safety Instructions LED -LCD television Owner’s Manual 5
ページ6に含まれる内容の要旨
Panel Control Introduction - This is a simplified representation of front panel. - Here shown may be somewhat different from your TV. Panel Control Press this key to open/close signal source options 8 SPDIF Digital Audio Optical output. 1 TV/AV menu. Connect the audio L/R and video cables to your 9 AV OUT Menu display. Press to access the on-screen other video equipment. 2 MENU menu display. Connect cable pr antenna signal to the TV, either Press to adjust the volume. In the MENU screen, 0 A
