ページ1に含まれる内容の要旨
CASTER / WHEEL
REPLACEMENT INSTRUCTIONS
THIS PROCEDURE SHOULD ONLY BE PERFORMED BY AN AUTHORIzED
WEBER-STEPHEN PRODUCTS LLC SERVICE TECHNICIAN
WARNINg: gENUINE WEBER-STEPHEN REPLACEMENT PARTS MUST BE USED FOR ANY REPAIR OR REPLACEMENT.
YOUR ACTIONS, IF YOU FAIL TO FOLLOW THIS PRODUCT WARNINg, MAY CAUSE A FIRE, AN ExPLOSION, OR
STRUCTURAL FAILURE RESULTINg IN SERIOUS PERSONAL INjURY OR DEATH AS WELL AS DAMAgE TO PROPERTY.
(Will void all W arranty protection.)
DANgER: BEFORE PERFORMINg AN
ページ2に含まれる内容の要旨
1 DISCONNECTION OF HOSE FROM GAS SOURCE NORTH AMERCAN i GRills LP UNITS: WARNINg: Do not use a wrench to loosen the connection. Using A) Make sure gas supply is turned off at source. a wrench could damage the B) Disconnect LP cylinder from inside of cabinet base. C) Remove LP cylinder from cabinet base. regulator coupling and could cause a leak. Ng UNITS: A) Make sure gas supply is turned off at source. B) Slide collar of quick-disconnect back to remove flexible gas supply hose from g
ページ3に含まれる内容の要旨
2 LID ASSEMBLY AND COOKBOX COMPONENTS REMOVAL 3 DOOR ASSEMBLY REMOVAL TOOLS NEEDED: - FLATHEAD 4 GREASE TRAY / DRIP PAN REMOVAL
ページ4に含まれる内容の要旨
5 REMOVAL OF FRAME ASSEMBLY TOOLS NEEDED: - PHILLIPS 6 CASTER AND WHEEL ASSEMBLY REMOVAL - PHILLIPS TOOLS NEEDED: - FLATHEAD 2 4 - PLIERS 1 3 5
ページ5に含まれる内容の要旨
• REPLACEMENT PART INSTALLATION 7 CASTER AND WHEEL ASSEMBLY REINSTALLATION _ PHILLIPS TOOLS NEEDED: - HAMMER - WOOD 3 1 2 4 8 REINSTALLATION OF FRAME ASSEMBLY TOOLS NEEDED: - PHILLIPS
ページ6に含まれる内容の要旨
9 GREASE TRAY / DRIP PAN REINSTALLATION 10 DOOR ASSEMBLY REINSTALLATION TOOLS NEEDED: - FLATHEAD 11 LID ASSEMBLY AND COOKBOX COMPONENTS REINSTALLATION PROPOSITION 65 WARNINg: HANDLINg THE BRASS MATERIAL ON THIS PRODUCT ExPOSES YOU TO LEAD, A CHEMICAL kNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. (WaSh handS after handlinG thiS product.) WARNINg: Make sure all parts are assembled and hardware is fully tightened before operating the grill
ページ7に含まれる内容の要旨
WARNINg: Make sure all control knobs are turned to the OFF position before reconnecting gas supply and operating grill. Your actions, if you fail to follow this Product Warning, may cause a fire, an explosion, or structural failure resulting in serious personal injury or death as well as damage to property. 12 CONNECTION OF HOSE TO GAS SOURCE NORTH AMERCAN i GRills WARNINg: Do not use a wrench LP UNITS: to tighten connection. Using a A) Reinstall LP cylinder into cabinet base. wrench
ページ8に含まれる内容の要旨
ATTENTION: This product has been safety-tested and is only certified for use in a specific country. Refer to country designation located on outside of box. These parts may be gas-carrying or gas-burning components. Please contact Weber-Stephen Products LLC Customer Service Department for genuine Weber-Stephen Products LLC replacement part(s) information. WARNINg: Do not attempt to make any repair to gas-carrying or gas-burning components without contacting Weber-Stephen Products LLC Cu
