ページ1に含まれる内容の要旨
HLTDC15/HLTDC19/HLTDC20
LCD TV
USER MANUAL
Please read this manual carefully
before using this TV set and keep it
for future reference.
ページ2に含まれる内容の要旨
Important Safety Instructions CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DANGEROUS VOLTAGE Uninsulated Dangerous Voltage, that may be of sufficient magnitude to constitute a risk of electric shock, is present within the cabinet of this unit. ATTENTION The Owner's Manual contains important operating and maintenance instructions. For your safety, it is necessary to refer to th
ページ3に含まれる内容の要旨
Important Safety Instructions 10. POWER SOURCES This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions. 11. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by it
ページ4に含まれる内容の要旨
Safety Instructions PRECAUTIONS FCC WARNING-This equipment may CAUTION:USE OF CONTROLS OR generate or use radio frequency ADJUSTMENTS OR PERFORMANCE energy.Changes or modifications to this OF PROCEDURES OTHER THAN equipment may cause harmful THOSE SPECIFIED HEREIN MAY interference unless the modifications are RESULT IN HAZARDOUS RADIATION expressly approved in the instruction EXPOSURE. manual.The user could lose the authority to operate this equipment if an unauthorized change or modifi
ページ5に含まれる内容の要旨
To users: Thank you for purchasing our LCD-TV. Before connecting the LCD-TV and turning on the power, please read this book carefully. Please keep this book for later use. If the unit is disabled by an electrostatic discharge, please turn off the power to the unit and turn it back on to reset. CONTENT Safety Notice Items................................................................................... 1 Front Panel Controls.......................................................................
ページ6に含まれる内容の要旨
Safety Notice Items Incorrect usage may cause fire or electric shock. To prevent this, please do as required when you are installing, using and cleaning this machine. To insure your safety and extend the life-span of LCD-TV, please read the following items carefully before using: l Please read and understand all the instructions before operation; l Please keep this manual for later use; l Please comply strictly with the warning instructions on the machine and in this book; l Pleas
ページ7に含まれる内容の要旨
Front Panel Controls 2 3 4 5 1 TV/AV MENU VOL- VOL+ CH- CH+ POWER 7 6 Control Panel Function 1. Power supply switch 2.TV/AV Selects the input signals: PC/COMPONENT/AV/SV/TV 3. MENU Press to select the main menu 4. VOL- Volume down / Left orientation to adjust the item in the OSD VOL+ Volume up / Right orientation to adjust the item/Press to enter 5. CH- TV channel down / to select the item in the menu CH+
ページ8に含まれる内容の要旨
Pr Pb Y R L V ANT IN PC AUDIO IN AUDIO IN VIDEO IN S-VIDEO COMPONENT IN VGA IN Pr Pb Y R L V ANT IN PC AUDIO IN AUDIO IN VIDEO IN S-VIDEO COMPONENT IN VGA IN Connection Options DVD STOP P L AY /PA U S E O P E N /C L O S E P R E W N E X T DVD insert The above figure is for reference only, connections may differ depending upon the models Antenna Input Connect cable or antenna signals to the TV, either direc- tly or through your cable box. Earph
ページ9に含まれる内容の要旨
Remote Control Key Functions When using the remote control, aim it Buttons on the remote control towards the remote sensor on the TV Stand By DVD Open/close POWER TV/AV TV/DVD OPEN/CLOSE TV/AV and input selection Scan SCAN RE CA LL DIS PL AY MU TE TV/DVD Mute Return to Previous Channel 1 2 3 4 Call Screen Display Program Number 5 6 7 8 Select MONO,STEREO, SAP in NTSC system SLEEP CCD CCD ( closed caption) On / Off 9 9 0 0 P.STD MTS/SAP TV Sleep button Adjust Picture Mode CH+ Volume/Channel Sele
ページ10に含まれる内容の要旨
Remote Control Installing Batteries ! Remove the battery cover. ! Insert two size AA batteries matching the +/-polarities of the battery to the +/- marks inside the battery compartment. Precautions As strong light may interfere with the Make sure that there is no signals, change your position to obstacle between the remote operate the remote control if controller and television set. the television cannot be turned on or off as expected. Make sure that two AA 1.5V alkaline Keep the re
ページ11に含まれる内容の要旨
Connection Instructions Grounding Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes. External Equipment Connections Antenna Connection - Antenna or Cable Service with a Cable Box Connections - For optimum picture quality, adjust antenna direction if needed. Mul
ページ12に含まれる内容の要旨
Connection Instructions PC Setup You can use your LCD-TV as a monitor for your personal computer using a VGA cable (not supplied). Connection and use steps: 1.Read the user guide supplied with your computer and ensure that it has a VGA connector; 2.Make sure that the power of the LCD -TV and the PC are off; 3.Connect a D type 15-pin VGA interface cable ( not supplied ) to the VGA video interface connector on the PC. Then connect the other end to the VGA video interfac
ページ13に含まれる内容の要旨
Connection Instructions VCR Setup - To avoid picture noise (interference), leave an adequate distance between the VCR and TV Connection and use steps: 1.Read the user guide supplied with your AV devices and ensure that it has Composite or S-Video connectors; 2.Make sure that the power of the LCD-TV and the AV device are off; Connection Option 1 Set VCR output switch to 3 or 4 and then tune TV to the same channel number. Connection Option 2 1. Connect the audio and video cables from t
ページ14に含まれる内容の要旨
Connection Instructions Cable TV Setup - After subscribing to a cable TV service from a local provider you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV. - For further information regarding cable TV service, contact your local cable TV service provider(s). Connection Option 1 1. Select 3 or 4 with channel switch on cable box. 2. Tune the TV channel to the same selected output channe
ページ15に含まれる内容の要旨
Basic Operating Instructions Turn on the LCD-TV POWER TV/AV TV/DVD OPEN/CLOSE When the POWER button is pressed and the LCD-TV SCAN RE CA LL DI SP LA Y M UT E is turned on, the indicator light on the front of the LCD-TV 1 2 3 4 changes from red to green. When the LCD-TV is turned off 5 6 7 8 SLEEP CCD 9 9 0 0 using the power button, the LCD-TV will go into standby MTS/SAP P.STD CH+ mode and the indicator light turns red. VOL MENU VOL - + EXIT 10 + CH- Note: ST OP SE TU P PAUS E/ S
ページ16に含まれる内容の要旨
Basic Operating Instructions Select the TV Channel You Want You can use the number keys on the remote control to directly select TV channels. The LCD-TV can store up to 181 channels , and you can press the keys on the remote control or on the panel to make a selection. Picture Mode Press P.STD button on the remote control for menu display . For desired mode as follows: PERSONAL STANDARD MILD FRESH Program Scan Press SCAN button to scan through all the memorized TV channels. The scan will paus
ページ17に含まれる内容の要旨
Menu Operations * In this manual, the OSD (On Screen Display) may be differ from your TV These are examples to illustrate the TV's operation. Press TV/AV to select the input source. The menu for each source is different . 1. Press MENU button to display the main menu, and VOL+/VOL-to select the main menu . 2. Press CH+/CH- to scroll through the parameters 3. Press VOL+/VOL- buttons to make changes to the parameters 4. Press the EXIT button to exit the menu Picture Menu Options Picture quali
ページ18に含まれる内容の要旨
Menu Operations Picture Menu Options continued 2. Press CH+/CH- button to enter the picture menu and to go up and down to select the desired option . 3.Press VOL+/VOL- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired picture quality has been achieved . Function: BRIGHTNESS :Adjust the brightness of the picture . By increasing the level, it will lighten the dark parts of the picture and by decreasing
ページ19に含まれる内容の要旨
Menu Operations Sound Menu Options continued You can adjust sound options to the levels you prefer. 2. Press CH+/CH- button to enter the audio menu and to go up and down to select the desired option . 3.Press VOL+/VOL- button to increase and decrease the level to adjust the selected option to your preference . 4. Repeat step 2 and step 3 until desired sound quality has been achieved .. Function : VOLUME : Adjust the volume of your TV BALANCE : Adjust the balance of the audio output
ページ20に含まれる内容の要旨
Menu Operations Function Menu Options Menu Language Selection: The OSD menus can be shown onscreen in the various languages. First select the system language. 1. Press MENU button and VOL+/VOL- until the following menu appears on the screen. FUNCTION INPUT SOURCE TV LANGUAGE ENGLISH CC MODE OFF BLUE SCREEN ON RESET 2. Press
