ページ1に含まれる内容の要旨
TFT-LCD TV
OWNER'S MANUAL
Please READ this manual carefully before
operating your TV, and retain it for future
reference.
MODELS:
HL26B
HL26S
HL32B
HL32S
HL37B
HL37S
HL40B
HL42S
HL42B
ページ2に含まれる内容の要旨
WARNING RISK ELECTRIC SHOCK DO NOT OPEN WARNING : To reduce the risk of electric shock do not remove cover or back. No user-serviceable parts inside refer service to qualified service personnel. Safety of operators has been taken into consideration at the design and manufacture phase, but inappropriate operation may cause electric shock or fire. To prevent the product from being damaged, the following rules should be observed for the installation, use and maintenance of th pr
ページ3に含まれる内容の要旨
IMPORTANT SAFETY INSTRUCTIONS Read all of the instructions before using this appliance. When using this appliance, always exercise basic safety precautions, including the following: 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer`s instructions. 8) Do
ページ4に含まれる内容の要旨
SAVE THESE INSTRUCTIONS Thank you for using our Haier product. This easy-to-use manual will guide you in getting the best use of your product. Remember to record the model and serial number. They are on label in back of the unit. Model number serial number Date of purchase Staple your receipt to your manual. You will need it to obtain warranty service. 4 TV LCD-TFT
ページ5に含まれる内容の要旨
Introduction Contents Time Menu Warnin g . . . . . . . ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . Date /Time setting................................................... Saf ety I nst ruc tio ns . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... Timer on setting...................................................... Introduction Timer off setting...................................................... Con tro ls . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ページ6に含まれる内容の要旨
Introduction Controls -This is a simplified representation of front panel. -Here shown may be somewhat different from your TV. Front panel controls HL26B HL32B HL37B HL40B HL42B 1.INPUT: all input source display and OK confirm. INPUT 1 2.CH( ) Program minus and plus, menu CH options 2 3.VOL( ) Volume increase and decrease, menu reset and entry VOL 3 4.MENU Menu display MENU 5. POWER : Is used to activate the 4 display or return to standby mode. 5 HL26S HL32S HL37S HL42S AUDIO2 Input 7 c
ページ7に含まれる内容の要旨
Connection Options Back panel controls Back panel controls Audio Output Antenna Input Connect audio from S-Video Input Connect cable or antenna HDMI2 Connect S-Video out from various types of equipment. signals to the TV, either connect a signal to an S-VIDEO device to the Note: In standby mode, directly or through your HDMI/DVI. S-VIDEO input. these ports will not work. cable box. AUDIO/VIDEO output AV OUT L R Y2 Pb2 Pr2 L R PC/DVI PC HDMI1 OPTICAL ANT IN HDMI2 AC IN Y 1 Pb1 Pr1
ページ8に含まれる内容の要旨
EXIT INFO ARC NPUT Introduction Universal Remote Controller - The remote controller cannot be operated unless the batteries are properly loaded. - When using the remote control, aim it at the remote control sensor on the TV. TV DVD VCR SETBOX CABLE AUDIO Function introduction Press the SELECT button repeatedly to select one of the system modes in which the remote control can be used. When the desired device is selected, the corresponding POWER LED lights on 5seconds. Turns your TV or any othe
ページ9に含まれる内容の要旨
EXIT INFO ARC NPUT Installation External Equipment Connections Accessories S E LECT CH.LIST FAV.LIST AUDIOLIST PIP SWAP AUDIOSWAPPOSITION TFT-LCD TV P.MODE S.MODE CC FREEZE OWNER'S MANUAL M O D E L : L 4 0 A 8 A OK Please READ this manual carefully before operating your TV, and retain it for future reference. VOL+ CH+ VOL- CH- Q.VIEW Power cable Alkaline battery(AAA) 2 Remote controller Owner`s manual Antenna Connection Generally speaking, to enjoy a clearer pictur
ページ10に含まれる内容の要旨
Installation External Equipment Connections NOTE: All cables shown are not included with the TV. Choose Your Connection There are several ways to connect your television, depending on the components you want to connect and the quality of the signal you want to achieve. The following are examples of some ways to connect your TV. Choose the connection which is best for you. VCR connection - To avoid picture noise (interference), leave an adequate distance between the VCR and TV Connection Opt
ページ11に含まれる内容の要旨
Installation External Equipment Connections External A/V Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). AV OUT L R Y2 Pb2 Pr2 L R How to use Y 1 L R S-VIDEO P b 1 Pr1 VIDEO L R 1. Select the input source with using the INPUT button on
ページ12に含まれる内容の要旨
Installation External Equipment Connections DTV connection - This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below. - This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i). How to connect Use the TV`s (Y, PB, PR) , VGA or HDMI jack for video connections,
ページ13に含まれる内容の要旨
Installation External Equipment Connections PC connection How to connect 1. To get the best picture quality, adjust the PC graphics card to 1024 x768 . 2. Use the TV`s PC or DVI (Digital Visual Interface)Audio IN port for video connections, depending on your PC connector. If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of eitherVGA IN or DVI IN to display the PC on the TV. If the graphic card on the PC does output analog and digital R
ページ14に含まれる内容の要旨
Installation External Equipment Connections Monitor Out Setup The TV has a special signal output capability which allows you to hook up a second TV or monitor. Connect the second TV or monitor to the TV`s AV OUT. See the Operating Manual of the second TV or monitor for further AV OUT L R Y2 Pb2 Pr2 L R details regarding that device`s input settings. Y 1 P b 1 Pr1 L R S-VIDEO VIDEO L R Notes: YPbPr, VGA, HDMI,DTV input sources cannot be used for Monitor out.
ページ15に含まれる内容の要旨
Installation Cable sample HDMI Cable (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) Owner s Manual 15
ページ16に含まれる内容の要旨
Installation External Equipment Connections Connecting Headphones You can connect a set of headphones to your set if you wish to watch a TV programme without disturbing the other people in the room. Plug a set of headphones into the 3.5mm mini-jack socket on the rear panel of the set. PC/DVI OPTICAL HDMI1 AUDIO IN Note Prolonged use of headphones at a high volume may damage your hearing. You will not receive sound from the speakers when you connect headphones to the system
ページ17に含まれる内容の要旨
Operation Operation -In the manual, the OSD (on screen display) may be different from your TV`s, because it is just an example to help you with the TV operation. -There are several options you might need to set up in order for your TV to work properly. Read the instructions that follow. Switching On/Off the TV set 1. First, connect power cord correctly. 2. Select the viewing source by using INPUT button on the remote control. 3. When finished using the TV, press the POWER button on th
ページ18に含まれる内容の要旨
Operation Channel menu This TV set has three methods to set channels, which are respectively Auto Scan, manual Scan fine tune. In this section, how to use the remote control to set channel is explained. You can also use buttons on the TV set to set channel. A password is required to gain access to Channel menu if the Lock of Edit program menu is turned on. Automatic Scan - Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the All Cha
ページ19に含まれる内容の要旨
Operation Channel menu Manual Scan If excessive channel signals of unwanted programs are received in local area, manual search function is recommended. Tuner Air Video Type Air Auto Scan Audio 1 Press the MENU button and then use / button to select the Channel NO 4 Manual Scan Time Channel menu. Fine Tune Frequency 67.250MHz A B C Channel Edit Program 2 Press the button and then use / button to select Tuner. 0k Rename Function 3 Press the button and then use /
ページ20に含まれる内容の要旨
Operation Channel menu Edit Program You can create your own Favorite List. Use the FAV.LiST button on the remote control when a channel is highlighted and then you can add or delete the channel to/from the Favorite List. You can skip some channel; You can lock some channel; Tuner Air Music Ch No Name Fav Lock Skip Video Auto Scan Audio Manual Scan Time Fine Tune A B C Channel Edit Program Rename Function Page 1/1 Lock 1 Press the MENU button and then use / button to sele
