ページ1に含まれる内容の要旨
USER'S MAN UAL
Before using the TV, please read this manual thoroughly,
and retain it for future reference.
ELCHW261
PARTNO. IESO90
ページ2に含まれる内容の要旨
Federal Communications Commission Statement NOTE The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user's authority. NOTE This equipment has been tested and found to comply with the limits for a class B digital Device, pursuant to part 1 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
ページ3に含まれる内容の要旨
CONTENTS Important safety instructions ........................................................................................................... 3 Preparation for using your new TV ................................................................................................. 5 Base installation instruction ............................................................................................................ 5 Learning about your -iV ....................................................
ページ4に含まれる内容の要旨
The lightning flash symbol with an arrowhead inside a triangle alerts the user about an uninsulated dangerous voltage that may be of sufficient magnitude to constitute CAUTION a risk of electric shock. CAUTION: TO REDUCE THE RISK OF AN ELECTRIC SHOCK, The flash with the symbol of an exclamation point DO NOT REMOVE THE COVER (OR BACK). inside a triangle alerts the user about important THERE ARE NO USER SERVICEABLE PARTS operating and maintenance instructions related to INSIDE. FORANY REQUIRED SER
ページ5に含まれる内容の要旨
ImPortant safety instructions 15. POWER SOURCE: This TV should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions. 16. POWER CORD PROTECTION: Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon
ページ6に含まれる内容の要旨
r new TV Pre aration for usin Base installation instruction 1. Lay a cloth or other soft material that can afford adequate weight on a flat table to avoid damage to the LCD screen. 2. Put the TV back upward and the LCD screen downward and keep it flat on the table-board. 3. Take out the base and insert it into the installing slot in the lower part of the TV in the arrow direction as illustrated in the figure. 4. Fasten the base and the TV set together with the 4 screws provided. 5
ページ7に含まれる内容の要旨
Preparation for using your new TV Learning about your TV Operate your TV via the buttons located on the front or side of cabinet or use the remote control. The terminals located on back of TV provides all the connections from other equipment to TV. View the front connection panel )ut selection Up Down Up Down Dn/Standby) indicator --Remote receiver View the back connection panel Input 6
ページ8に含まれる内容の要旨
Preparation for using your new TV Selecting a location for the TV 1. Place the TV on an open stand in a location where light does not directly hit the screen. 2. Place the TV far enough from the walls to allow proper ventilation. Inadequate ventilation may cause overheating, which may damage the TV. NOTE- = Please contact a local dealer for wall mounting. Connection to other devices The side pane| connection Update jack The equipment with AV or S-Video output function ( such as VCR, DVD, set=top
ページ9に含まれる内容の要旨
Preparation for using your new TV The back pane| connection The equipment with HDMI output jack ( such as DVD players, set-top boxes, etc.). Computer OR OR j i iii AUDIO AMPLIFIER DVD With Component jacks 8
ページ10に含まれる内容の要旨
Preparation for using your new TV Connecting your TV Caution" Do not plug in the TV until you have finished connecting all of your equipment, Connecting to an antenna To enjoy the televison program transmitted by your local TV station, you need an indoor or outdoor antenna (not supplied). An outdoor antenna is necessary for superior picture quality. If you are a subscriber of your local cable network net, the outdoor or indoor antenna is not needed. Connect the equipment as shown below. Side Pan
ページ11に含まれる内容の要旨
Preparation for using your new TV Connecting HDMI Supports digital connections between HDMI = enabled AV devices such as (DVRs, DVD, BluRay, HDDVD, AV receivers and digital devices). No sound connection is needed for an HDMI to HDMI connection. NOTE: Some devices such as a DVR or DVD players require a HDMI signal to be set via the output in the devices' settings. Please consult your device user manual for instructions. What is HDMI? HDMI, or high=definition multimedia interface, is a next=genera
ページ12に含まれる内容の要旨
Preparation for using your new TV For subscribers to Basic Cable "rv Service For basic cable service not requiring a Converter/Descrambler box, connect the CATV 75 ohm Coaxial Cable directly into the Antenna Jack on the back of the television. For subscribers to Scrambled Cable "IV Service If you subscribe to a cable service which requires the use of a Converter/Descrambler box, connect the incoming cable to the Converter/Descrambler box and connect the output of the box to the Antenna Jack on t
ページ13に含まれる内容の要旨
Using the remote control Preparing the remote control for use Installing the remote control batteries 1. Open the battery cover on the back of the remote control. 2. Install twoAAAsize(1.5V) batteries. Matchthe+ and = signs on the batteries to the signs on the battery compartment. 3. Close the battery cover. Note: 1.Dispose of your batteries in a designated disposal area. Do not throw batteries into fire. 2.Do not mix battery types or combine used batteries with new ones. 3.Remove dead batteries
ページ14に含まれる内容の要旨
Using the remote centre[ Learning about the remote centre[ Power indicator Power ON/OFF ............................................. Switch among TV, Video, S-Video, Component, HDNI and VGA Select TV Select digital ST:Return to previous channel SOUND: Select the sound mode DISPLAY: Display current Status PICTURE: Select the picture information Volume u .............................. Channel up Nute Volume down MENU: Call up the main menu EXIT: On Screen Display (OSD) menu exit OSD menu Up arrow
ページ15に含まれる内容の要旨
Understanding the TV features • Multimedia = All in one TV receiver, Video Honitor and PC display, • Wider viewing angle for 16:9 and 4:3 display screens = over a 160 degree viewing angle and a 16:9 display panel, • Digital display device = Irrespective of magnetic or geomagnetic effects, this device accurately reproduces images without any distortion or blur, • Closed caption decoder = You may view specially labeled (cc) TV programs, movies, news, prerecorded tapes, etc, with either a dialogue
ページ16に含まれる内容の要旨
Basic operation Use [Hute] button Press the [Mute] button to mute the sound, Press the [Mute] button again to resume the sound, Select picture modes Press the [PICTURE] button to select the picture mode from four options: Standard, Movie, User and Vivid, In the "User" mode you can adjust the picture mode based upon your personal preference, Select sound modes Press the [sound] button to select sound modes from Standard, Speech, User, and Music. In the User Mode, you can adjust the audio mode bas
ページ17に含まれる内容の要旨
Basic operation Use [GUIDE] button Press the [GUIDE] button to display features of the ATSC program and the EPG function. Use [DISPLAY] button Press the [D]:SPILAY] button to view current source information. Use [EXIT] button Press the [EXIT] button to exit the OSD menu. Se|ect channels by numbers To select a channel: Press the channel number you would like to go to. For example, to select channel number 120, press buttons 1, 2 and 0, respectively. Use [HENU] button Press the [MENU] button to di
ページ18に含まれる内容の要旨
Basic operation Video mode adjustment 1. Press HENU to open the OSD option 2. Press A or V to highlight Video, then press II_to enter the Video menu"Refer to page 12 "Select picture mode . Press A or V to highlight an option, then press 4 or I_ to adjust the option. You can adjust: • Picture Mode =Adjusts the Picture Mode. You can select Standard, Movie, User, or Vivid. . Brightness = You can increase or decrease the brightness of the picture. Increasing the brightness can add more light to dark
ページ19に含まれる内容の要旨
Basic operation . Balance - Adjusts the volume of the left and right speakers. . Equalizer mYoucan select the frequency you want to adjust and change its value. . Surround Sound -Turns the surround sound effect on or off. • Auto Volume Control = Turns automatic volume control on or off. The option keeps the audio in a preset range to eliminate large spikes in volume. . SPDIF Type = Selects the SPDIF type. You can select PCM, Dolby Digital, or Off. Note: Via SPDIF Type, you can choose the optical
ページ20に含まれる内容の要旨
Basic operation Parental Control 1. Press MENU to open On Screen Display (OSD) option 2. Press A or V to highlight Parental, then press I_ to enter the Parental menu. When you first use this function, the default password is [0000]. Once you input this password, you can: , Press A or V to highlight an option, then press _I or I_ to adjust the option. You can adjust: - Channel Block = This function will let you block any channel you want. - Program Block =A. Rating Enable is on B. U.S. TV Ratings
