ページ1に含まれる内容の要旨
Owner’s manual & Installation manual
TB851P/
TB853W
8-INCH WIDE COLOUR LCD TV
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2005: Clarion Co., Ltd. QZ-8000K
Printed in Japan / /
280-8212-00
2005/3 (Y·Y)
*TB851P/TB853W(001-cover)E 1 05.2.24, 5:21 PM
ページ2に含まれる内容の要旨
Thank you for purchasing this Clarion TB851P/TB853W. ∗ This owner’s manual is for the TB851P/TB853W. ∗ Please read this owner’s manual completely before operating this equipment. ∗ After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). ∗ Check the contents of the enclosed warranty card and keep it carefully with this manual. Contents 1. FEATURES ................................................................................................................... 2
ページ3に含まれる内容の要旨
TV Display Cleaning 2. PRECAUTIONS • Cleaning the cabinet Use a soft, dry cloth and gently wipe off the dirt. For tough dirt, apply some neutral detergent WARNING diluted in water to a soft cloth, wipe off the dirt gently, then wipe again with a dry cloth. For your safety, the driver should not watch the TV or operate the controls while driving. Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or Watching the TV while driving is prohibited by law in som
ページ4に含まれる内容の要旨
Remote Control 3. CONTROLS / / 4. PART NAMES Note: • Except for the following buttons, the remote control button names are the same as the buttons on the main LCD panel closed / / unit. Operating Buttons Note: [SRC] button [ ] • Be sure to read this chapter while referring to the front diagrams in chapter “3. CONTROLS” on page 5 • Press to turn on the power. OPEN/CLOSE (unfold). • Press and hold for 2 seconds or longer to turn off the power. Signal transmitter Inserting the Battery 1. Turn
ページ5に含まれる内容の要旨
Remote Control 3. CONTROLS / / 4. PART NAMES Note: • Except for the following buttons, the remote control button names are the same as the buttons on the main LCD panel closed / / unit. Operating Buttons Note: [SRC] button [ ] • Be sure to read this chapter while referring to the front diagrams in chapter “3. CONTROLS” on page 5 • Press to turn on the power. OPEN/CLOSE (unfold). • Press and hold for 2 seconds or longer to turn off the power. Signal transmitter Inserting the Battery 1. Turn
ページ6に含まれる内容の要旨
TV Display Cleaning 2. PRECAUTIONS • Cleaning the cabinet Use a soft, dry cloth and gently wipe off the dirt. For tough dirt, apply some neutral detergent WARNING diluted in water to a soft cloth, wipe off the dirt gently, then wipe again with a dry cloth. For your safety, the driver should not watch the TV or operate the controls while driving. Do not use benzene, thinner, car cleaner, etc., as these substances may damage the cabinet or Watching the TV while driving is prohibited by law in som
ページ7に含まれる内容の要旨
English 5. OPERATION Note: Be sure to read this chapter referring to the front diagrams in Basic Operation chapter “3. CONTROLS” on page 5 (unfold). Opening and adjusting the LCD Panel calibration function The LCD panel’s maximum angle of tilt can be panel adjusted to match the installation configuration WARNING within the automobile. •Perform this with the LCD panel closed. •To prevent the battery from going dead, operate this unit with the engine running 1. Press and hold the [OPEN] button for
ページ8に含まれる内容の要旨
English Basic Operation ● To adjust the slide position Turning power ON or OFF 1. Hold down the [TILT] button and release it 1. Press the [POWER] button. when a beep is heard. Use to turn the power on or off. The LCD panel slides forward or backward. Note: This adjusted slide position is stored in • The LCD panel does not store away even if the memory. power is turned off. If not using for a long period of time, press the [OPEN] (open/close) button on ∗ There are 3 adjustable positions available
ページ9に含まれる内容の要旨
English TV Operation Select a station from the list WARNING Two types of lists can be displayed. One is the For your safety, the driver should not preset list and the other is the channel list. watch or operate TV while driving. Viewing • The preset list is a list of channels already and operating the TV while driving are stored in the memory. prohibited by law in some countries. • The channel list is a list of receivable channels. Watching TV ●Selecting a station from the preset list Note: 1. P
ページ10に含まれる内容の要旨
English TV Operation Auto store function Selecting the screen size This function automatically stores a received Five screen size are supported: normal, wide, broadcast as a preset channel. full wide, cinema1 and cinema2. 1. Press the [P.LIST] button for 2 second or Note: • The screen size cannot be selected while the more. The broadcast stations are vehicle is in motion. automatically stored in the memory in order 1. Press the [WIDE] button to select the screen starting from the currently recei
ページ11に含まれる内容の要旨
English Yellow Gray Yellow Black Black Red Black White Operating with an external device ●Select the video mode To view video images: ●How to connect to video 1. Press the [SRC] button to select VTR1 or VTR2. The setting shifts in the sequence Use the VTR mode to transfer output audio or shown below, each time the [SRC] button is images such as video. pressed. TV ➔ VTR1 ➔ VTR2 ➔ VISUAL1 ➔ VISUAL2 ➔ TV ➔ Notes: • See the instruction manual for the connected device to learn how to operate the vide
ページ12に含まれる内容の要旨
English Operating with an external device ●Viewing video images 1. Press the [SRC] button to select VISUAL1 or VISUAL2. The setting shifts in the sequence shown below, each time the [SRC] button is pressed. TV ➔ VTR1 ➔ VTR2 ➔ VISUAL1 ➔ VISUAL2 ➔ TV ➔ ... Video from the external device connected to the video in terminal (visual input 1 or visual input 2) appears on the screen. Notes: • See the instruction manual of the external device to be connected to find out how to operate that external devic
ページ13に含まれる内容の要旨
English Changing the settings (ADJUST mode) 1. Press the [ADJ] button to display the How to set ADJUST mode screen. (Main screen during TV mode) Each press of the [ADJ] button switches the ADJUST mode screen. 2. Press the [w] or [z] button to select the item to set. 3. Press the [A] or [D] button to select the setting value. 4. Press the [ENT] button to return to the original screen. (ADJ_MONITOR screen) (ADJ_EXTERNAL screen) (BRIGHT adjustment) (ADJ_HVAC screen) (ADJ_OTHER screen) (Main screen
ページ14に含まれる内容の要旨
English Changing the settings (ADJUST mode) Adjust the screen image quality Rear monitor lock ∗ The factory setting is at “OFF”. Screen image quality 1. Select “MONILOCK” on the Adjust the screen luminance, brightness, hue ADJ_EXTERNAL screen. and color level to view video at your own preferred image quality. 2. Press the [A] or [D] button to select ON or OFF. •You can only make this adjustment in TV/VTR/ VISUAL modes while the vehicle is stopped. • Only the screen luminance and brightness Switc
ページ15に含まれる内容の要旨
English Changing the settings (ADJUST mode) Select the FM modulator and RCA Set the number of multiscreens (list audio output levels screen) ∗ The factory setting is at “HIGH”. ∗ The factory setting is at “12”. • In TV mode, the FM modulator output is at 1. Select “LIST” on the ADJ_OTHER screen. “HIGH”, even when set to “LOW” during TV 2. Press the [A] or [D] button and select “8” mode. or “12”. • Not displayed during VISUAL mode. 1. Select “AUDIO LEV” on the Select the country (only on TB851P)
ページ16に含まれる内容の要旨
English Changing the settings (ADJUST mode) Select PAL or NTSC This setting allows you to select the video system for input to the VTR. This can be separately set for VTR 1, VTR 2, VISUAL 1 and VISUAL 2. ∗ The factory setting is at “AUTO”. • This setting can be made in the VTR and VISUAL modes. 1. Select “PAL/NTSC” on the ADJ_OTHER screen. 2. Press the [A] or [D] button and select “PAL”, “NTSC” or “AUTO”. Setting the caution message for use during CCD camera operation This setting can be made wh
ページ17に含まれる内容の要旨
English 6. TROUBLESHOOTING ■ If you think that something is wrong with your unit, check the following points before requesting servicing. Problem Cause Action No image display. The parking brake is not set. Check that the parking brake is set. Vehicle is moving. No video is displayed on the unit while driving. Park the vehicle before playing this unit. (Set the parking brake.) No TV mode (function). To watch TV, press the source button and check that the TV screen is now set. Monitor is at OFF.
ページ18に含まれる内容の要旨
English 7. SPECIFICATIONS Audio output: LCD Monitor HIGH 230 ± 100 mV (at VTR Input 130 mV rms) Screen size: LOW 125 ± 50 mV (at VTR Input 130 mV rms) 7-inch wide type (Load resistance 10 kΩ) (176.4 mm Width ✕ 99.2 mm Height) Display method: General Transmission type TN LCD Drive method: Power source voltage: TFT(thin-film transistor) active matrix DC13.2 V (10.8 to 15.6 V) driving Ground: Negative Pixels: 336,960 (1440 ✕ 234) Current consumption: Less than 2.0 A Weight: 2.2 kg TV Tuner Dimensio
ページ19に含まれる内容の要旨
English TB851P/TB853W Installation and Wire connection manual ■ Contents 1. BEFORE STARTING ............................................................... 21 2. PACKAGE CONTENTS ........................................................... 21 3. GENERAL CAUTIONS ............................................................ 22 4. CAUTIONS ON INSTALLATION .............................................. 22 5. INSTALLING THE MAIN UNIT ................................................. 23 6. REMOVING THE
ページ20に含まれる内容の要旨
English 3. GENERAL CAUTIONS 1. Do not open the case. There are no user 2. Use a soft, dry cloth to clean the case. Never serviceable parts inside. If you drop anything use a rough cloth, thinner, benzine, or into the unit during installation, consult your alcohol, etc. For tough dirt, apply a little cold dealer or an authorized CLARION service or warm water to a soft cloth and wipe away centre. the dirt gently. 4. CAUTIONS ON INSTALLATION 1. Prepare all articles necessary for installing 5. Use
