ページ1に含まれる内容の要旨
INTEGRATED DIGITAL FULL HD COLOUR TELEVISIONS
32WLU550FHID
Operation Instructions
ページ2に含まれる内容の要旨
TABLE OF CONTENTS 1 1-Important Information ...............................................................1 1.1-Cleaning the screen and cabinet... .......................................................1 1.2-Disposing of your TV at the end of service life... ...................................1 1.3-Superior features of your integrated digital television ............................1 1.4-Receiving digital broadcasting channels ...............................................1 1.5-Changing the plu
ページ3に含まれる内容の要旨
Important Information 1 LCD panels are produced with state-of-the-art technology. However, there may be missing or lit spots on the screen under certain circumstances. That does not mean that the product is faulty. 1.1-Cleaning the screen and cabinet... After powering off, wipe the screen and the cabinet clean with a soft and dry cloth. We recommend that you do not use patented polishes or solvents on the screen or cabinet since they may cause damage. 1.2-Disposing of your TV at the end of
ページ4に含まれる内容の要旨
1.5-Changing the plug The supplied mains cable already has a mains plug fitted, however should you need to replace it at any time please refer to the appropriate wiring information below for your particular cable. 2
ページ5に含まれる内容の要旨
2 Features of your new television We would like this product, which has been manufactured in modern facilities in accordance with total quality principles, to offer you the best performance. Therefore, please read this entire manual carefully before you use your TV and keep it in a safe place for future reference. 2.1-Special Features • Full HD • HDCP feature • MHEG 1.06 • CI Slot input • 8-day EPG (Electronic Program Guide) • Favourite channel list in digital mode (maximum 6 lists) • Compat
ページ6に含まれる内容の要旨
3 Important Safety Instructions This symbol is used to warn the user about the “dangerous voltage” contained inside the housing of the product that may create a risk of electrical shock. This symbol is used to remind the user important usage and service instructions supplied with the TV. 1) Please READ the operating • Never install the TV into closed places instructions before using such as bookcases or cabinets unless the TV for the first time. adequate ventilation is provided. 2) Please
ページ7に含まれる内容の要旨
10) Never operate your 13) Make sure that the power TV close to water. cable is not stepped on and Operating your TV, that there is no bending for example, near a at the plug sections, plug bathtub, washbasin, heads and TV output point. kitchen washbasin, washing basin, wet basement and swimming pool can cause 14) Use only the add-ons/accessories fire or electric shock. specified by the manufacturer. • Do not allow your TV to get wet. Never 15) Use only brackets or pour any liquids onto s
ページ8に含まれる内容の要旨
18) Wipe the TV cabinet 20) Disposing of the exhausted clean with a soft and dry batteries: cloth. Wipe dust from the • Dispose of the exhausted screen gently with a soft batteries in accordance with cloth. Stubborn stains the local laws and regulations in order to can be cleaned with a protect our environment. cloth slightly moistened with soap and lukewarm water. Never 21) Do not dispose of your TV use solvents such as thinner or gasoline with regular household waste. for cleaning. Unpl
ページ9に含まれる内容の要旨
Start 4 Remove your television carefully from its Not 1: Your TV will switch to the STANDBY box. You can keep the packaging of your mode in five minutes if there is no broadcast television to use in future. signal from the aerial. Note 2: Your TV is equipped to operate with Contents of the box TV buttons in case your remote is broken or Power cable the batteries are exhausted. Remote control 3. To power on your television, 2 batteries press any numerical key or PR+ or Note: Scart, HDMI,
ページ10に含まれる内容の要旨
5 Your new television 5.1-TV Control Panel Volume Level Down/Up Program Down/Up button or or button or or or Stand by indicator Menu button / Source selection button Bright light: TV is in Stand-by or or Dimmed light: TV is On On-Off / Standby button No light: Power Cable is not connected. 5.2-Rear and Side External Connections 1-Component video input (Y) 2-Component audio input (L) 3-Component video input (Pb) 4-Component audio input (R) 5-SPDIF Digital audio output 6-Component video input (
ページ11に含まれる内容の要旨
5.3-Remote Control Stand-by mode On/Off button Temporary sound mute (Mute) button AV modes selection menu button Picture Format selection button PAT (Picture and Teletext) Mode ZOOM mode selection button Subtitle selection button (D) Not used on this model (D) Numeric buttons TV, Radio, Data, Favorite channel selection button (D) Page Stop button in Txt mode (Hold) EPG selection button (D) Question/Answer button in Txt mode (Reveal) Information button Index page button in Txt mode MENU button Ex
ページ12に含まれる内容の要旨
Performing the initial power-on settings 6 6.1.5-Temporary sound mute 6.1-TV controls (MUTE) 6.1.1-Temporary on/off (STAND-BY) To temporarily mute the sound of When you press the red STAND- your television, press the MUTE BY button located on the upper left button on your remote control. hand side of your remote control In that case, MUTE symbol will while your television is switched appear on the screen. When you on, the sound and the picture will press the same button a second go o
ページ13に含まれる内容の要旨
SETUP 6.2-Turning on the TV and Setting the Channels AUTO TUNING MANUAL TUNING FIRST TIME INSTALLATION When you turn on your television for the first time, FIRST TIME INSTALLATION CHECK AERIAL CABLE IS CONNECTED. PRESS OK KEY TO CONTINUE message is displayed. If the antenna connections MENU SELECT BACK are correct, press OK button to continue. COUNTRY SELECTION menu will be displayed. Select the country by using Up/ Select AUTO TUNING tab and Down, Left/Rightmovement buttons confirm by
ページ14に含まれる内容の要旨
Highlight the Channel tab by ADDITIONAL INFORMATION means of Up/Down buttons and directly enter the frequency number Please note that Encrypted channels of the channel you want to search, may not be stored after scanning in if you know, by using the numeric the Digital TV channels. If this is the keys on the remote control. If you case then you will need to rescan the don’t know the frequency number, channels again but this time change the you can scan frequencies by using LIST SCRA
ページ15に含まれる内容の要旨
6.3.4-Program Table 6.3.4.2-Creating favorite channels list With the program table, you can see the stored channels in a list, switch between You can create 6 favorite channel TV channels and Radio channels or create lists according to your personal your favorite channels list for 6 TV and Radio preferences. To do this press channels according to your preference. the RED button when you are in Program table. Favorite Lists will Select the PROGRAM TABLE item be displayed. All TV channels
ページ16に含まれる内容の要旨
You can select the channel by using To perform language selection, the Up/Down movement buttons select Subtitling Language 1, and navigate through the program Subtitling Language 2, Audio data with Right movement button. Language 1, Audio Language 2 To get further information about tab from the Language Settings the program press INFO button menu by using Up/Down and detailed information about the movement buttons and make your selected program will be displayed. language selection with L
ページ17に含まれる内容の要旨
Note 2: The password for both of these desire by means of the Program Table. Press features has been set as 0000 at the factory. AV button on your remote control, select You can change the password as you wish ANALOG TV tab from the SOURCE menu under Change PIN item in the Access by using Up/Down movement buttons Control menu. and confirm by pressing the OK button. Your TV will switch to Analog mode. Press 6.3.6.3-User Interface Options the MENU button on your remote control. From th
ページ18に含まれる内容の要旨
AUTOPROGRAM 6.4.2.2-If you do not know the SEARCHING % 20 channel number STOP Press the MENU button. Move To stop the process at any given time, to the SETUP menu by pressing please press the MENU button. The the Down movement button in Program Table, which will allow you to sort the Main Menu and confirm your the channels as you wish, will be displayed selection with the OK button. after the automatic search is complete. Setup menu will be displayed. Select the system in which you 6
ページ19に含まれる内容の要旨
6.4.4-Program Table After setting is complete, press the EXIT button to exit the menu. Press the MENU button. Move to the PROGRAM TABLE tab by pressing the 6.4.4.3-Skipping a stored channel Down movement button in Main Menu and In the event that you do not wish confirm your selection with the OK button. to see certain programs while Program Table menu will be displayed. navigating through the channels using the PR+/PR- buttons, PROGRAM TABLE then you can use this function. Select the 00
ページ20に含まれる内容の要旨
7 Settings of Your New Television 7.1- Sound Menu Settings 7.1.4-AVL (Automatic Volume Limiting) You may perform volume settings by Television transmitters have different sound using the VOL+ or VOL- buttons on levels. This can be noticed as high and low your television or the VOL+/VOL- volume levels in different channels while buttons on your remote control. You switching from one program to another. Using can perform other Sound settings by the Left/Right movement buttons, select ON.
