ページ1に含まれる内容の要旨
MODEL
FWD-42PV
PROTOCOL MANUAL
(User Control)
Preliminary
as of
February 22, 2005
SONY Corporation
Home Electronics Network Company
ページ2に含まれる内容の要旨
1. Communication Parameters Communiction Method RS232C Synchronous Method Asynchronous Baud Rate 9600bps Character Length 8bit Parity None Start Bit Length 1bit Stop Bit Length 1bit Flow Control None 2. Pin Assignment Monitor side : D-sub 9pin Host side : D-sub 9pin 5 4 3 2 1 5 4 3 2 1 9 8 7 6 9 8 7 6 Pin № Function Pin № Function 1 1 NC NC 2 TD 2 RD 3 RD 3 TD 4 NC 4 NC 5 GND 5 GND 6 NC 6 NC 7 NC 7 NC 8 8 NC NC 9 9 NC NC
ページ3に含まれる内容の要旨
3. Communication Data Format (a)Control message № Item Value 1 Header 0x8C: Control 2 Category 0xXX Function 0xXX 3 Data1 （Length ） 0xXX 4 Data2 （Data1 ） 0xXX 5 : : 0xXX : : 0xXX DataX 0xXX X X+1 Check Sum 0xXX * Check Sum: The total from №1 to №X, when value exceeds 255, 1byte of data is confirmed the bottom. * When sending controls in sequence, keep interval of more than 500ms between the commands. * When sending an enquiry right after sending the control of a same command, also keep interval
ページ4に含まれる内容の要旨
(3)Enquiry answer (Command cancel) Item Value № 1 Header 0x70: Answer 2 Answer 0x03: Command Canceled 3 Check Sum 0xXX The packet was received normally,but the command was cancelled because the 0x03: Command Canceled function was not in adjustable mode, such as "--" a function displayed as in user menu. * Check Sum: The total from №1 to №2, when value exceeds 255, 1byte of data is confirmed the bottom. (4)Error answer Item Value № Header 0xE0: Answer 1 2 Answer* 0x00: No Function Error 0x01
ページ5に含まれる内容の要旨
1. General Function (a)Mode Control Function Syntax Header Category Data1 Data2 Check Sum Control 0x8C 0x00 Code Table(1-a)[a] 0x02 Code Table 0xXX (1-a)[b] Enquiry 0x83 0xFF 0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table 0xXX Completed (1-a)[b] Code Table(1-a) Command [a]Function [b]Range
ページ6に含まれる内容の要旨
Code Table(1-a) continued Command [a]Function [b]Range/Switch Code Control Enquiry Standby Power On Index Number 0x01-0xFF 0x10 Yes Yes Disable Enable 0x13 Power Saving 0x00 Standard Yes Yes Disable Enable 0x01 Reduce 0x14 Speaker Out 0x00 ON Yes Yes Disable Enable 0x01 OFF 0x16 HD Mode 0x00 1080i Yes Yes Disable Enable 0x01 1035i 0x17 0x00 DTV RGB Mode Yes Yes Disable Enable 0x01 PC H/Comp 0x18 Sync Mode 0x00 Yes Yes Disable Enable Video 0x01 OFF 0x1B Clock Display 0x00 Yes Yes Disable Enable O
ページ7に含まれる内容の要旨
Code Table(1-a) Command [a]Function [b]Range/Switch code Control Enquiry Standby Power On U3(HD15) 0x25 Input Detect(Option1)0x00 No Yes Disable Enable 0x01 U1(CVBS/Y,C) No Yes Disable Enable U2(BNC) No Yes Disable Enable 0x02 Reserved 0x03 No Yes Disable Enable 0x04 UN No Yes Disable Enable Reserved 0x05 No Yes Disable Enable 0x06 Reserved No Yes Disable Enable Reserved No Yes Disable Enable 0x07 Reserved 0x08 No Yes Disable Enable 0x09 Reserved No Yes Disable Enable Reserved 0x0A No Yes Disabl
ページ8に含まれる内容の要旨
IP Address Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x42 0x05 Address 0 Address 1 Address 2 Address 3 0xXX 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Answer Header Answer Check Sum 0x70 Completed Control 0x70 0x00 0x70 0x03 0x73 Command Canceled IP Address ex) 192.128.14.1 -->192(0xC0)...Address 0 128(0x80)...Address 1 14(0x0E)...Address 2 1(0x01)...Address 3 * IP Address commands are active also in stand-by mode. Code Table(1-a) C
ページ9に含まれる内容の要旨
IP Address Setting IP Address Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x42 0x05 Address 0 Address 1 Address 2 Address 3 0xXX 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Subnet Mask Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x61 0x05 Address 0 Address 1 Address 2 Address 3 0xXX 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Gateway Address Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum
ページ10に含まれる内容の要旨
(b)Color Matrix Function Syntax Header Category Data1 Data2 Data3 Data3 Check Sum Control 0x8C 0x00 Code Table(1-b)[a] 0x04 Code Table Code Table Code Table 0xXX (1-c) (1-b)[b] (1-d) Function Syntax Header Category Data1 Data2 Check Sum Enquiry 0x83 0x00 Code Table(1-b)[a] Code Table Code Table 0xXX (1-c) (1-d) Answer Header Answer Check Sum 0x70 Completed Control 0x70 0x00 0x73 Command Canceled 0x70 0x03 Answer Header Answer Return to Data Size Return Data1 Return Data2 Return Data3 Check Sum E
ページ11に含まれる内容の要旨
( ｃ)Time Control - Clock Set (Hour, Minute) Function Syntax Header Category Data1 Data2 Data3 Check Sum Control 0x8C 0x00 0x22 0x03 Hour: Minute: 0xXX 0x00-0x17 0x00-0x3B Syntax Header Category Function Data1 Data2 Check Sum 0x22 Enquiry 0x83 0x00 0xFF 0xFF 0xA3 Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x71 Limit Over 0x70 0x01 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Return Data2 Check Sum Enquiry 0x7
ページ12に含まれる内容の要旨
- On Timer, Off Timer Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x00 Code Table(1-f)[a] 0x03 Hour: Minute: 0xXX 0x00-0x17 0x00-0x3B Function Syntax Header Category Data1 Data2 Check Sum Enquiry 0x83 0x00 Code Table(1-f)[a] 0xFF 0xFF 0xXX Check Sum Answer Header Answer 0x70 Completed Control 0x70 0x00 0x70 0x01 0x71 Limit Over 0x72 Limit Under 0x70 0x02 0x73 Command Canceled 0x70 0x03 Return to Data Size Answer Header Answer Return Data1 Return Data2 Check Sum Enqui
ページ13に含まれる内容の要旨
2. Picture/Sound (a)Picture/Sound Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x10 Code Table(2-a)[a] 0x02 Code Table 0xXX (2-a)[b] Enquiry 0x83 0xFF 0xFF 0xXX Answer Header Answer Check Sum 0x70 0x00 0x70 Completed Control 0x70 0x0 １ 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table 0xXX Completed (2-a)[b] Code Table(2-a) Command [a]Function [b]Range/
ページ14に含まれる内容の要旨
( ｂ)Color Temp Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x10 Code Table(2-b)[a] 0x03 Code Table Code Table 0xXX (2- ｃ) (2-b)[b] Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x10 Code Table(2-b)[a] Code Table 0xFF 0xXX Answer Header Answer Check Sum 0x70 0x00 0x70 Completed Control 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Return Data2 Check Sum Enquiry 0x70 0x00 0x03 Code Table Code Table 0xXX Compl
ページ15に含まれる内容の要旨
3. Size/Shift (a)8Bits Register Function Syntax Header Category Data1 Data2 Check Sum Control 0x8C 0x20 Code Table(3-b)[a] 0x02 Code Table 0xXX (3-b)[b] Enquiry 0x83 0xFF 0xFF 0xXX Check Sum Answer Header Answer 0x70 Completed Control 0x70 0x00 0x71 0x70 0x01 Limit Over 0x72 0x70 0x02 Limit Under 0x73 Command Canceled 0x70 0x03 Return to Data Size Answer Header Answer Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table 0xXX Completed (3-b)[b] Code Table(3-b) Command [a]Function [b]Range/Swi
ページ16に含まれる内容の要旨
4. Status Enquiry (a)Model Name Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x00 0xFF 0xFF 0xB1 Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table 0xXX Completed (4-a) Code Table(4-a) Format Select FWD-42PV1 0x22 (b)Serial Number Function Syntax Header Category Data1 Data2 Check Sum Enquiry 0x83 0x30 0x01 0xFF 0xFF 0xB2 Answer Header Answer Return to Data Size Return Data1 Return Data2 Return Data3 Return Data4 Check Sum
ページ17に含まれる内容の要旨
(g)Shutdown Log Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x30 0x11 0xFF 0xFF 0xC0 Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Shutdown 0xXX Completed Log Return Data1: 0x00-0xFF Code Table(4-c) Shutdown Information bit0 Reserved bit1 1: FAN Movement Abnormal, 0: Normal 1: Panel communication Abnormal, bit2 bit3 1: Temperature Sensor Abnormal, 0: bit4 1: Main Power Abnormal, 0: Normal 1: Digital Power Abnormal (3.3V, 5V) bit5
ページ18に含まれる内容の要旨
5. User Reset Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x50 Code Table(5) 0x02 0xFF 0xXX Answer Header Answer Check Sum 0x70 0x00 0x70 Completed Control 0x70 0x03 0x73 Command Canceled Code Table(5) Command Function Range/Switch code Control Standby Power On Enquiry Yes No Disable Enable 0x00 Picture Reset Yes No Disable Enable 0x01 Audio Reset Size, Shift, Dot Clock, Phase Yes No Disable Enable 0x02 Size Reset Contrast, Brightness, Chroma, Phase Yes No Disable Enable 0
