ページ1に含まれる内容の要旨
FLAT WIDE DISPLAY MONITOR
FWD-50PX3
PROTOCOL MANUAL (For Customer)
ページ2に含まれる内容の要旨
Table of Contents 1. Communication Parameters ......................................................... 1 2. Pin Assignment ..................................................................................... 1 3. Communication Data Format ....................................................... 1 4. General Function ................................................................................. 3 5. Analog Signal Detect Function ................................................... 9 6. Priorit
ページ3に含まれる内容の要旨
1. Communication Parameters 3. Communication Data Format (a) Control message Communication method RS-232C Synchronous method Asynchronous No. Item Value Baud rate 9600bps 1 Header 0x8C: Control Character length 8bit 2 Category 0xXX Parity None 3 Function 0xXX Start bit length 1bit 4 Data1 (Length) 0xXX Stop bit length 1bit 5 Data2 (Data1) 0xXX Flow control None : : 0xXX : : 0xXX X DataX 0xXX 2. Pin Assignment X+1 Check Sum 0xXX * Check Sum: Sum total of 1 to X. Lower one-byte data is validated w
ページ4に含まれる内容の要旨
(c) Answer message 4 Error answer 1 Control answer No. Item Value No. Item Value 1 Header 0xE0: Answer 1 Header 0x70: Answer * 2 Answer 0x00: No Function Error * 2 Answer 0x00: Completed 0x01: Check Sum Error 0x01: Limit Over 0x02: Data Length Error 0x02: Limit Under 3 Check Sum 0xXX 0x03: Command Canceled * 0x00: No Function Error Packet header,category or function code are not included in this protocol. 3 Check Sum 0xXX 0x01: Check Sum Error Check sum value or received packet is not correct. *
ページ5に含まれる内容の要旨
4. General Function (a) Mode Control Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x00 Code Table (1-a) [a] 0x02 Code Table (1-a) [b] 0xXX Enquiry 0x83 0xFF 0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table (1-a) [b] 0xXX Completed Code Table (1-a) [a]Function [b]Range/S
ページ6に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x06 Color System 0x00 Auto Yes Yes Disable Enable 0x01 NTSC 0x02 NTSC4.43 0x03 PAL 0x05 PAL-M 0x06 PAL-N 0x07 PAL60 0x0B Picture Inversion 0x00 OFF Yes Yes Disable Enable 0x01 Auto 0x02 On 0x0C Picture Orbit 0x00 OFF Yes Yes Disable Enable 0x01 ON 0x0D Orbit Range 0x00 Small Yes Yes Disable Enable 0x01 Middle 0x02 Large 0x0E Orbit Cycle 0x00 Speed1 (10 sec ) Yes Yes Disable Enable 0x01 Speed2 (30 sec) 0x0
ページ7に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x24 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable (Option1) 0x01 FW10 (VIDEO, S-VIDEO) BNC 0x02 FW11 (BNC) 0x03 Reserved 0x04 FW31/32 0x05 FW50 (RGB) 0x06 FW20 (UART + CTRL-S) 0x07 FW13 (COMPONENT) RCA 0x08 FW15 (HDMI x 2) 0x09 FW16 (Digital x 1) 0x0A Reserved 0x0B Reserved 0x0C Reserved 0x0D Reserved 0x0E Reserved 0x0F Not Connect 0x25 Input Detect 0x00 FW12 (HD15) No Yes Disable Enable (Option2) 0
ページ8に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x31 Active Picture 0x00 Left (P&P)/Main (PinP) Yes Yes Disable Enable 0x01 Right (P&P)/Sub (PinP) 0x02 Swap 0x32 Picture Size (P&P) 0x00-0x0E Yes Yes Disable Enable 0x33 Sub Picture Size 0x00 Large Yes Yes Disable Enable (PinP) 0x01 Small 0x34 Picture Position 0x00 Position1 Yes Yes Disable Enable (PinP) 0x01 Position2 0x02 Position3 0x03 Position4 0x35 PAP Input Detect 0x08 INPUT1 RGB (Analog) No Yes Dis
ページ9に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x44 Logo Illumination & 0x00 Logo Off Yes Yes Enable Enable Status LED 0x01 Logo On (Low) 0x02 Logo On (High) 0x04 LED Off 0x05 LED On 0x45 Control Mode 0x00 Main + Remocon Yes Yes Disable Enable 0x01 Main 0x02 Remocon 0x03 All Off *5 0x04 Limited 0x46 On Off Timer Mode 0x00 Every Day (Repeat) Yes Yes Enable Enable 0x01 Day Of Week 0x47 On Timer Enable bit0 Sunday 1: Enable, 0: Disable Yes Yes Enable Enab
ページ10に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x67 IP Setting Result 0x00 Done Yes No Enable Enable 0x01 Error 1 (UART Commu.) 0x02 Error 2 (Duplication) 0x03 Error 3 (IP Add Setting) 0x04 Error 4 (GW Add setting) 0x05 Error 5 (DNS1 Setting) 0x06 Error 6 (DNS2 Setting) 0x07 Error 7 (Sbnt Msk Setting) 0x68 Speed Setting 0x00 100Mbps/Full Duplex Yes Yes Enable Enable 0x01 100Mbps/Half Duplex 0x02 10Mbps/Full Duplex 0x03 10Mbps/Half Duplex 0x04 Auto 0x70
ページ11に含まれる内容の要旨
Code Table (1-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x74 Digital Signal Detect 0x00 VIDEO No Yes Disable Enable *6 (DVI/HDMI/etc.) 0x01 PC *7 0x75 Signal Status 0x00 Stable No Yes Disable Enable 0x01 Unstable/No Signal 0x76 VIDEO Signal Detect 0x00 NTSC No Yes Disable Enable 0x01 PAL (SECAM) *3: Option3 Slot is Not Connect Now. *4: Auto Signal Detect becomes Disable. When Option Slot is connected, Option command is Enable. *5: Restricts a part of keys oper
ページ12に含まれる内容の要旨
6. Priority Signal Select Function (a) Mode Control Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 Code Table (2-a) [a] Code Table (2-d) 0xFF 0xXX Answer Header Answer Return to Data Size Return Data1 Data2 Check Sum Enquiry 0x70 0x00 0x02 Code Table (2-a) [b] 0xFF 0xXX Completed Code Table (2-a) [a]Function [b]Range/Switch Code Command Control Enquiry Standby Power On 0x77 Priority Signal Select 0x00 Input1 Auto No Yes Disable Enable 0x01 Input1 RGB 0x02 Input1 YPbPr Co
ページ13に含まれる内容の要旨
Code Table (1-c) Format Select 0x00 480P 0x01 1080i 0x02 720P 0x03 480i Code Table (1-d) Input Select 0x00 HD15 (Component) 0x01 Option1 0x02 Option2 (c) Time Control Clock Set (Hour, Minute) Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x00 0x22 0x03 Hour: 0x00-0x17 Minute: 0x00-0x3B 0xXX Syntax Header Category Function Data1 Data2 Check Sum Enquiry 0x83 0x00 0x22 0xFF 0xFF 0xA3 Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over
ページ14に含まれる内容の要旨
Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Week: Code Table (1-e) 0xXX Completed Code Table (1-e) Week Select 0x00 Sunday 0x01 Monday 0x02 Tuesday 0x03 Wednesday 0x04 Thursday 0x05 Friday 0x06 Saturday On Timer, Off Timer Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x00 Code Ta
ページ15に含まれる内容の要旨
Code Table (1-f) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On Invert Timer 0x20 Invert Start Time _ Yes Yes Disable Enable 0x21 Invert End Time _ On Timer 0x50 Sunday _ Yes Yes Disable Enable 0x51 Monday _ 0x52 Tuesday _ 0x53 Wednesday _ 0x54 Thursday _ 0x55 Friday _ 0x56 Saturday _ 0x57 Every day _ Off Timer 0x58 Sunday _ Yes Yes Disable Enable 0x59 Monday _ 0x5A Tuesday _ 0x5B Wednesday _ 0x5C Thursday _ 0x5D Friday _ 0x5E Saturday _ 0x5F Every day _ (d) IP Address
ページ16に含まれる内容の要旨
DNS Secondary Syntax Header Category Function Data1 Data2 Data3 Data4 Data5 Check Sum Control 0x8C 0x00 0x64 0x05 Address 0 Address 1 Address 2 Address 3 0xXX 0x00-0xFF 0x00-0xFF 0x00-0xFF 0x00-0xFF Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x03 0x73 Command Canceled IP Address ex) 192.128.14.1 →192 (0xC0) Address 0 128 (0x80) Address 1 14 (0x0E) Address 2 1 (0x01) Address 3 * IP address command can be carried out even in the standby state. Code Table (1-a) [a]Function
ページ17に含まれる内容の要旨
Code Table (2-a) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x00 Contrast 0x00-0x64 Yes Yes Disable Enable 0x01 Brightness 0x00-0x64 Yes Yes Disable Enable 0x02 Chroma 0x00-0x32 Yes Yes Disable Enable 0x03 Phase 0x00-0x64 Yes Yes Disable Enable 0x04 Color Temp 0x00 Cool Yes Yes Disable Enable 0x01 Neutral 0x02 Warm 0x03 Custom 0x09 Sharpness 0x00-0x14 Yes Yes Disable Enable 0x0A NR 0x00 OFF Yes Yes Disable Enable 0x01 Low 0x02 Mid 0x03 High 0x0B Cinema Drive 0x00 A
ページ18に含まれる内容の要旨
Code Table (2-a) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x36 Default Volume Set 0x00-0x64 Yes Yes Enable Enable 0x37 Volume Select 0x00 Last Memory Yes Yes Enable Enable 0x01 Default Setting 0x38 Max Volume Set 0x32 50 Yes Yes Enable Enable 0x46 70 0x64 100 *1 Sound Mode = Custom Only is Enabled. (b) Color Temp Syntax Header Category Function Data1 Data2 Data3 Check Sum Control 0x8C 0x10 Code Table (2-b) [a] 0x03 Code Table (2-c) Code Table (2-b) [b] 0xXX Synta
ページ19に含まれる内容の要旨
8. Size/Shift (a) 8Bits Register Syntax Header Category Function Data1 Data2 Check Sum Control 0x8C 0x20 Code Table (3-b) [a] 0x02 Code Table (3-b) [b] 0xXX Enquiry 0x83 0xFF 0xFF 0xXX Answer Header Answer Check Sum Control 0x70 0x00 0x70 Completed 0x70 0x01 0x71 Limit Over 0x70 0x02 0x72 Limit Under 0x70 0x03 0x73 Command Canceled Answer Header Answer Return to Data Size Return Data1 Check Sum Enquiry 0x70 0x00 0x02 Code Table (3-b) [b] 0xXX Completed Code Table (3-b) [a]Function [b]Range/Switc
ページ20に含まれる内容の要旨
Code Table (3-b) [a]Function [b]Range/Switch code Command Control Enquiry Standby Power On 0x06 Auto Pixel Adjust 0xFF Execute Yes No Disable Enable 0x07 Dot Phase 0x00-0x1F Yes Yes Disable Enable 0x0B Multi Position 0x00 Position1 Yes Yes Disable Enable (2 x 2 ,1 x 2, 2 x 1) 0x01 Position2 *1 0x02 Position3 0x03 Position4 0x0C Multi Position 0x00 Position1 Yes Yes Disable Enable (3 x 3, 1 x 3, 3 x 1) 0x01 Position2 *1 0x02 Position3 0x03 Position4 0x04 Position5 0x05 Position6 0x06 Position7 0x
