ページ1に含まれる内容の要旨
50-200 FISH FINDER
Dual Frequency 50 & 200kHz Black Box Fish Finder
CODE: B-300806
Copyright 2006 Interphase Technologies Inc.
All rights reserved. Printed in Italy. No part of this publication may be reproduced or distributed in any form or by any
means, or stored in a database or retrieval system, without prior written permission of the publisher.
User Manual
ページ2に含まれる内容の要旨
Contents Important Information ............................................................................... 6 WARRRANTY STATEMENT ............................................................................... 6 CAUTION ............................................................................... 6 About this User Manual ............................................................................... 7 INTRODUCTION .............................................................................
ページ3に含まれる内容の要旨
3.1.10.4 Fish Symbols ........................................................................ 21 3.1.10.5 Water Temperature ............................................................... 22 3.1.11 Transducer Setup ............................................................................. 22 3.1.11.1 Keel Offset ........................................................................... 22 3.1.11.2 Calibrate Sound Speed .......................................................... 22 3.1.11.3 C
ページ4に含まれる内容の要旨
Important Information WARRRANTY STATEMENT Interphase Technologies, Inc. warrants this unit to be free from defects in material and workmanship. During the warranty period, Interphase Technologies, Inc. will repair or replace any component which fails in normal use without charges for parts or labour. To receive warranty service, the unit must be returned to a Interphase Technologies, Inc. Authorized Warranty Service Centre, freight charges prepaid along with a copy of the original retail purcha
ページ5に含まれる内容の要旨
About this User Manual INTRODUCTION The chart plotter combined with the sonar performance of the Fish Finder is one of the most advanced marine navigation system available. Please read carefully this User Manual to learn the operating features for your unit. Refer to your chart plotter User Manual for all other unit operating instructions. CONVENTIONS USED Throughout this User Manual, the labelled keys are shown in capital letters en- closed in square brackets, for example [ENTER]; the software
ページ6に含まれる内容の要旨
HOW THIS USER MANUAL IS ORGANIZED ♦ CHAPTER 1: Overview Introduction to the basic information on the Fish Finder, its features and use. ♦ CHAPTER 2: Fish Finder Helps you understand how the chart plotter is connected to the Fish Finder and how to operate to improve your fishing. ♦ ♦ ♦ ♦ ♦ CHAPTER 3: Setup your Fish Finder Description of the Fish Finder Setup menu. ♦ ♦ ♦ ♦ ♦ CHAPTER 4: 50-200 FISH FINDER Technical specification, dimension and installation of the 50-200 FISH FINDER and set up of t
ページ7に含まれる内容の要旨
1. Overview The Fish Finder consists of a high power transmitter, sensitive receiver and a transducer. The Fish Finder sends an electrical pulse to the transducer which contains an element that converts the pulse into acoustic (sound) wave which is sent through the water. As this wave travels from the transducer to the bottom, it may strike fish, structures, thermal clines (temperature changes in the water). When the wave strikes an object(s) a certain amount of the wave is reflected back to the
ページ8に含まれる内容の要旨
♦ STC (allows reducing or eliminating the surface clutter) ♦ Interference Rejection (allows reducing interference from other boats/ Fish Finders) ♦ Noise Filter ♦ Fish Symbol feature (*) ♦ Automatic Transducer Setup. Recognition for devices (automatic trasducer identification and parameters setup for best performance) ♦ Alarms Handling (Shallow Alarm, Depth Alarm, Fish alarm, Tempera- ture Upper, Temperature Lower) NOTE* On specific software version available. 1.2 SELECTING THE FISH FINDER POR
ページ9に含まれる内容の要旨
2. Fish Finder This chapter is intended to help you understand how the chart plotter with the Fish Finder connected operates to improve your fishing. 2.1 UNDERSTANDING THE FISH FINDER PAGE The display on chart plotters shows a history of time of the echoes received by the transducer. The chart plotters have a menu that allows adjustments to re- ceiver sensitivity, depth range and scrolling speed of the Fish Finder display. 1 Warning message Fish Finder Display window 2 6 3 Color Bar 7 4 Digital
ページ10に含まれる内容の要旨
Digital Depth Readout of the current bottom depth. Water Temperature Readout of the current water temperature returned by the TEMP 1 sensor included into specific transducers. Alarm Bar Bars showing the shallow water and deep water alarm values. The alarm is triggered when depth is outside the range. Depth ruler Vertical graduated bar. It is a scale which reflects the depth of the area being displayed. Variable Depth Marker (VDM) Horizontal line on to the Fish Finder Display with a depth la
ページ11に含まれる内容の要旨
fish, causing a display pixel to be turned on. As the boat passes over the fish, the distance to the fish decreases turning each pixel on at a shallower depth on the display. When the boat is directly over the fish, the first half of the arch is formed and since the fish is closer to the boat, the signal is stronger and the arch is thicker. As the boat moves away from the fish, the distance in- creases and the pixels appear at progressively deeper depths forming the remaining half of the arch. T
ページ12に含まれる内容の要旨
Fig. 2.2.1 - Page Selection menu The menu now shows four selections related to the Fish Finder, Full Display, 50/ 200kHz Full Display, Zoom Full Display and Chart/Fish display. Move the cursor to select the desired item and then press [ENTER]. NOTE When the Radar* is connected, two other displaying pages are available too, Radar/FF and Radar/FF/Chart/Nav Data. See the Radar* User Manual for more information. (*) ONLY FOR CM 11CV+/11CVS+/169 CS/169 CSI 2.2.2 Fish Finder Full Display page To displ
ページ13に含まれる内容の要旨
Fig. 2.2.2a - Sensitivity sub-menu Pressing [CLEAR] turns off the Sensitivity menu. The CLEAR key By pressing [CLEAR] the Variable Depth Marker (VDM) is hidden. The ZOOM IN and ZOOM OUT keys From this page pressing [ZOOM IN] once changes to Zoom 2X, pressing [ZOOM IN] twice changes to Zoom 4X, while pressing [ZOOM OUT] reverts to Zoom 2X and no zoom. 2.2.3 50/200 kHz Full Display page To display the Fish Finder Dual Display, follow this procedure: [PAGE] + "50/200 kHz Full Display" + [ENTER] Fi
ページ14に含まれる内容の要旨
Fig. 2.2.4 - Fish Finder Zoom Page The Depth Cursor is shown only on the unzoomed Fish Finder Display. The ZOOM IN and ZOOM OUT keys From this page pressing [ZOOM IN] changes to Zoom 4X, pressing [ZOOM OUT] changes to Zoom 2X. 2.2.5 Chart/Fish Display page To display the Chart page on the left half of the screen and the Fish Finder Display on the right half of the screen, follow this procedure: [PAGE] + "Chart/Fish Display" + [ENTER] Fig. 2.2.5 - Fish Finder Chart/Fish page The MENU key (to chan
ページ15に含まれる内容の要旨
Fig. 2.2.6 - Radar/FF page Otherwise to display the Radar and Fish Finder Combo pages, follow this procedure: [PAGE] + "Radar/FF/Chart/Nav Data" + [ENTER] Fig. 2.2.6a - Combo page When in Split/Combo pages, the active view is highlighted by a focus (Yellow frame). The keyboard commands are related to that focused view. To move the focus press [MENU] twice. 2.3 ZOOM MODES 2.3.1 The Bottom Lock Zoom The Bottom Lock Zoom mode is activated when the Fish Finder is in Auto Range or Bottom Lock mode (s
ページ16に含まれる内容の要旨
below the bottom of the screen, automatically moves up/down the current zoomed Fish Finder Display view and re-position the Variable Depth Marker (VDM) at the center of the screen. NOTE Pressing [CLEAR] hides the Depth Cursor and if the Fish Finder is in Auto Range or Bottom Lock mode switches into Bottom Lock Zoom mode. 2.4 INFO ON FISH FINDER: SYSTEM INFORMATION If you want to know information about the Fish Finder connected, follow the procedure: [MENU] + "SETUP" + [ENTER] + "SYSTEM INFORMATI
ページ17に含まれる内容の要旨
3. Setup your Fish Finder 3.1 FISH FINDER SETUP MENU The Fish Finder Setup menu provides access to additional functions, setup and layout/data field options. From the Fish Finder page, access this menu by pressing: [MENU] Fig. 3.1 - Fish Finder Setup menu 3.1.1 Preset Mode Allows applying the following Fish Finder operating mode presets Fish and Cruise. See the following table. [MENU] + "PRESET MODE" + [ENTER] Fish : Gain Mode = Auto, Range Mode = Auto, Frequency = do not change, Shift = 0, ST
ページ18に含まれる内容の要旨
Bottom Lock. [MENU] + "BOTTOM RANGE" + [ENTER] 3.1.5 Depth This option is available only when Range Mode is Manual and it is disabled in Auto Range and Bottom Lock Mode. [MENU] + "DEPTH" + [ENTER] 3.1.6 Shift Shows the depth from which start the bottom scanning. This option is available only when Range Mode is Manual and it is disabled in Auto Range and Bottom Lock Mode. [MENU] + "SHIFT" + [ENTER] NOTE The Bottom Range, Depth, Shift will apply to the currently selected frequency. 3.1.7 Frequency
ページ19に含まれる内容の要旨
increases. This is for the purpose of filtering out surface clutter. 3.1.9.4 STC Length If STC is Custom, it is possible to change the Length of the Sensitivity Time Constant. 3.1.9.5 STC Strength If STC is Custom, it is possible to change the Strength of the Sensitivity Time Constant. 3.1.9.6 Surface Noise Filter This function implements an advanced time varying filter that allows suppressing the surface clutter efficiently while leaving fish targets visible. NOTE Thus imposing the capability o
ページ20に含まれる内容の要旨
Icon : shows Fish icons Icon + Depth : shows Fish icons and their depth (accordingly to currently selected depth unit) The Fish icons displayed are among four different shapes depending on the size of the Target (Small, Med, Big, Huge). 3.1.10.5 Water Temperature Allows you to choose the Water Temperature label displayed over the Fish Finder Display between Primary and External. [MENU] + "WATER TEMPERATURE" + [ENTER] 3.1.11 Transducer Setup The Transducer Setup menu contains settings that does n
