ページ1に含まれる内容の要旨
INSTRUCTIONS
ページ2に含まれる内容の要旨
Viewfinder Indicators Autofocus frame Flash Autofocus Power focus Shutter speed Spot frame Aperture setting Exposure compensation / Manual exposure Spot metering Mode button SUBJECT FLASH MACRO REWIND DRIVE Do not use any device with a sharp tip. — 1 —
ページ3に含まれる内容の要旨
Description of controls (1) Hot shoe cover Shift button Shutter release button Power switch Selftimer button AF illuminator Flash switch Zoom buttons Strap attaching stud — 2 —
ページ4に含まれる内容の要旨
Table of contents Fill-in flash ..................................... 40 Description of controls (1) ................... 2 Special effects ................................... 42 Before you begin ................................. 5 Exposure mode switching .................... 42 Loading the batteries ............................ 5 Loading the film ................................... 7 Aperture-preferred auto mode .............. 43 Manual exposure mode ....................... 44 Unloading the fil
ページ5に含まれる内容の要旨
Thank you for purchasing the OLYMPUS IS-1. Please read this instruction manual carefully before using the camera. We also recommend that you shoot at least one roll of film just to familiarize yourself with the camera's features. Symbols used in this manual Correct Incorrect Operation Order of operation Automatic operation Attention Press lightly Lamp on Lamp blinking — 4 —
ページ6に含まれる内容の要旨
Before you begin... Loading the batteries *Insert two 3V lithium batteries as shown and *Be sure the power switch is OFF. replace the cover turning the lock screw *Turn the lock screw on the bottom of camera clockwise. counter clockwise to open the battery cover. WARNING: Do not mix different types of batteries NOTE: If the batteries are replayced while the power or new and old batteries at the same switch is ON, the camera may not resume time. standard shooting mode. In such a case, Use Panason
ページ7に含まれる内容の要旨
*Switch power ON. *Press the mode button and the + / – button simultaneously to check the remaining battery power. *Nothing appears if batteries are OK. However flashes, batteries are low, have spares at hand. If is displayed continuously, batteries should be replaced immediately. NOTE: After checking the batteries the camera is automatically reset to standard shooting mode. Remove batteries if you do not plan to use the camera for an extended period of time. — 6 —
ページ8に含まれる内容の要旨
Loading the film * Open the back cover by sliding the back This camera is designed to use DX-coded 35 mm cover release. film. DX coding, used by virtually all major film manufacturers, allows the camera to identify and NOTE: Avoid direct light when loading the film. set the film speed automatically, (refer to pg. 60) — 7 —
ページ9に含まれる内容の要旨
*Insert the film cartridge. Do not touch the * Align the film leader with the film loading indicator. shutter curtain with your finger or the film leader when loading. NOTE: Adjust the length of the film leader before loading, so that it matches the film loading NOTE: Make sure the film cartridge is not sticking indicator. Make sure the film leader tip is not out when aligning film. bent and the film edge is properly aligned and engaged with the film guide as shown. — 8 —
ページ10に含まれる内容の要旨
—The film will advance automatically and the exposure counter on the LCD panel will display the number "1" indicating the first picture on the roll when the power switch is turned ON. * Close the back cover. —If the film is improperly loaded, the LCD panel will display a blinking "E" and . In this case, open the back cover, and realign the film leader. —Use the window on the camera back to check the type of film loaded. — 9 —
ページ11に含まれる内容の要旨
Unloading the film *The camera automatically rewinds the film when you reach the end of the roll. Note: If you want to rewind the film before the end of the roll, open the mode cover and press the REWIND button. The final reading on the exposure counter before rewinding may be more than the number of exposures specified for the film. — 10 —
ページ12に含まれる内容の要旨
is displayed on the LCD panel while the — Once the film has been rewound, a blinking "E" film is rewinding. and will be displayed on the LCD panel. Further operations are not possible until the rewound film cartridge is removed. *Open the back cover, and remove the film cartridge from the camera. WARNING: Do not touch the shutter curtain inside the camera while removing the film cartridge NOTE: If the power is turned OFF while rewinding, operations will stop. However, rewind mode is not cancelle
ページ13に含まれる内容の要旨
Reset operation If you forget which mode you are in, the camera can be reset to automatically resume standard shooting mode. Standard shooting mode: Exposure mode: Program auto (P) Drive mode: Single (S) Light metering mode: ESP Flash mode: AUTO or AUTO-S Exposure compensation: ±0 Focusing: AF *Press the MODE button and + / – button simultaneously. — The camera will resume standard shooting mode, and other set modes will be cancelled. — 12 —
ページ14に含まれる内容の要旨
Simple point & shoot photography How to take pictures *Set power switch ON. *Press part A to remove the lens cap. —The lens will automatically adjust for wide angle shooting and standard shooting mode will be displayed on the LCD panel. — 13 —
ページ15に含まれる内容の要旨
*While looking through the viewfinder, aim the *Use the zoom (T/W) button to adjust the size of your subject in the frame (Telephoto camera at the subject. or Wide angle). —Press the "T" (Telephoto) on the zoom button to —Press the "W" (Wide-angle) on the zoom button zoom in. (The maximum focal length in the "T" to zoom out. (The minimum focal length in the position is 135 mm.) "W" position is 35 mm.) — 14 —
ページ16に含まれる内容の要旨
autofocus frame *Position your subject within the autofocus *Press the shutter release button halfway to frame in the center of the viewfinder. focus. —When correct focus has been achieved, the auto- focus indicator will light-up in the viewfinder. —If the autofocus indicator is blinking, correct focus has not been achieved. If this occurs, let go off the shutter release button. Make sure your subject is within the autofocus frame in the center of the viewfinder and press the shutter release but
ページ17に含まれる内容の要旨
*When correct focus has been achieved *Switch the power OFF when the camera is (autofocus indicator has lit up), press the not in use. shutter release button fully. As soon as the shutter is released, the film will automatically —When the power is switched OFF, the lens will automatically retract. advance to the next frame. — 16 —
ページ18に含まれる内容の要旨
Shooting range: From 1.2 m (3.9 ft) to In Macro mode the shooting range is from 0.6 m (2.0 ft) to Normal shooting 0 m (0 ft) 1.2 m (3.9 ft) Macro shooting 0 m (0 ft) 0.6 m (2.0 ft) When shooting in extremely dim light, the AF illuminator on the front of the camera will emit a beam of infrared light to measure the distance to the subject and assist in the autofocus operation. — 17 —
ページ19に含まれる内容の要旨
Holding the camera Hold the camera correctly and be careful not to block the AF illuminator or flash with the camera strap or your fingers. NOTE: The longer the focal length, the greater the potential for the effects of camera shake. To avoid movement make sure you are holding the camera properly with both hands. — 18 —
ページ20に含まれる内容の要旨
Auto flash photography For shooting in dimly lit or strongly backlit locations. *When the in the viewfinder blinks, slide the flash switch to activate the flash. — Flash will pop up AUTO will light on the LCD panel. — 19 —
