ページ1に含まれる内容の要旨
AUGUST 2007
AC1100A
AC1101A
AC1102A
Multi DVI System
CATX Series
© Copyright 2007. Black Box Corporation. All rights reserved. 5310196-01 02
1000 Park Drive • Lawrence, PA 15055‐1018 • 724‐746‐5500 • Fax 724‐746‐0746
CUSTOMER Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)
SUPPORT FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax 724-746-0746
INFORMATION Mailing addre
ページ2に含まれる内容の要旨
FCC/IC RFI STATEMENTS, EU DECLARATION OF CONFORMITY MULTI DVI SYSTEM. FEDERAL COMMUNICATIONS COMMISSION FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY Contents INTERFERENCE STATEMENTS AND Chapter Page This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, INDUSTRY CANADA that is, in strict accorda
ページ3に含まれる内容の要旨
CHAPTER 1: Specifications MULTI DVI SYSTEM. 1.Specifications 2. Introduction Cable Required: Between transmitter and receiver: Cat5/Cat6 2.1 Overview Compliance: CE; FCC Class A, IC Class A The Multi DVI System extends DVI video signals over Cat5/6 cable. All models support Video Support: DVI Single Link single link DVI video modes. Resolution: 1600x1200 , 1080P (if graphics card supports reduced clock rate) This manual covers Multi
ページ4に含まれる内容の要旨
CHAPTER 3: Setup and Installation MULTI DVI SYSTEM. 3.2.2 CONNECTIONS ON THE SINGLE-PORT MULTI DVI 3. Setup and Installation The AC1100A, AC1101A, AC1112A units support DVI video over CAT5 cable . 3.1 Cabling Considerations Figure 3-1 shows the video only Multi DVI System Transmitter connections, and Figure • We recommend mounting and connecting all cabling to the Multi DVI System 3-2 shows the receiver connections. components before applying power. Please note recom
ページ5に含まれる内容の要旨
CHAPTER 3: Setup and Installation MULTI DVI SYSTEM. 3.2.3 CONNECTIONS ON THE DUAL DAISYCHAINABLE RECEIVER 4. Troubleshooting The dual daisychainable receiver is used when the same signal is distributed to 4.1. Common Problems multiple display devices on a single cable in a daisychain or loop-through fashion. CAT5 Cable lengths must not exceed 600 ft between units. In most cases, nearly every issue with the Multi DVI System can be resolved by Setup and cabling are the same
ページ6に含まれる内容の要旨
APPENDIX A:Cabling Pinouts MULTI DVI SYSTEM. Appendix B. Status LED’s The Multi DVI System feature “status-at-a-glance” LED’s to ensure the units are functioning Appendix A. Cabling Pinouts properly and to isolate problems with input signals, units, and/or cabling thus saving time during installation and troubleshooting. Reference the following tables for information on theses indicators. The UTP connector also contains LED indicators on either side to provide visual cues Tabl
ページ7に含まれる内容の要旨
APPENDIX C:Compression Mode MULTI DVI SYSTEM. APPENDIX D. DDC Modes Appendix C. Compression Mode The Multi DVI System features the ability to send DDC display identifiers to the video source in order to determine display capabilities. The DDC is a data communication channel used in plug and play devices to accurately report a The Multi DVI System features two video compression modes to enable high resoluiotn displays capabilities and identify the manufacturer. If this data
ページ8に含まれる内容の要旨
APPENDIX D:DDC modes MULTI DVI SYSTEM. APPENDIX D. DDC Modes Appendix E. Rackmounting Units The Rackmount Kits include brackets for mounting a transmitter, receiver, or a dual daisychainable receivers in a 19 rack. Figure F-1 shows the 2-Unit Rackmount Bracket (AC1011), which holds three units in a 19" x 1U rack. Not shown are brackets for 6 units . The 6-Unit Transmitter/Receiver Bracket (AC1012) is like the AC1011 but occupies 2U of space instead of 1U in a 19" rack
ページ9に含まれる内容の要旨
MULTI DVI SYSTEM. NOTES NOTES 8 15 16 9
