ページ1に含まれる内容の要旨
User Manual
ECOR 264 Digital Video Recorder
ECOR 264 Digital Video Recorder
ECOR 264-8/4 F2
ECOR 264-8/4 F2
(8/4-channel DVR ECOR 264 without DVD+RW)
(8/4-channel DVR ECOR 264 without DVD+RW)
ECOR 264-8/4 D2
ECOR 264-8/4 D2
( (8 8//4 4--c ch ha an nn ne ell D DV VR R E EC CO OR R 2 26 64 4 w wiit th h D DV VD D+ +R RW W) )
ページ2に含まれる内容の要旨
EVE R F O C U S E L E C T R O N I C S C O R P O R A T I O N ECOR 264 F2/D2 DVR Series Instruction Manual 2010 EverFocus Electronics Corp www.everfocus.com All rights reserved. No part of the contents of this manual may be reproduced or transmitted in any form or by any means without written permission of the Everfocus Electronics Corporation. Release Date: September 2010 QuickTime is a registered trademark of the Apple Computer, Inc. Windows is a registered tr
ページ3に含まれる内容の要旨
Safety Precautions Refer all work related to the installation of this product to qualified service personnel or system installers. Do not block the ventilation opening or slots on the cover. Do not drop metallic parts through slots. This could permanently damage the appliance. Turn the power off immediately and contact qualified service personnel for service. Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers. There
ページ4に含まれる内容の要旨
TABLE OF CONTENTS 1 PRODUCT OVERVIEW ........................................................................................................................ 1 1.1 FEATURES .......................................................................................................................................................... 1 1.2 PACKAGE CONTENTS ..........................................................................................................................................
ページ5に含まれる内容の要旨
3.4 PLAYBACK ........................................................................................................................................................ 22 3.5 PTZ ................................................................................................................................................................. 24 3.5.1 General PTZ control (if PTZ cameras are installed) ............................................................................................... 2
ページ6に含まれる内容の要旨
4.10.3 User ........................................................................................................................................................................ 77 4.10.4 I/O Control .............................................................................................................................................................. 79 4.10.5 Misc. ......................................................................................................................
ページ7に含まれる内容の要旨
Chapter 1 1 PRODUCT OVERVIEW The ECOR 264 F2/D2 series‘ digital video recorders are equipped with the latest H.264 compression technology and offer both enhanced recording capacity and fast high quality image transmission over network. Numerous functions and the enhanced recording settings make these digital video recorders the perfect choice for various application fields. 1.1 FEATURES - dual stream for slow network bandwidth control - low noise / fanless housing design - user-frie
ページ8に含まれる内容の要旨
1.2 PACKAGE CONTENTS - Digital Video Recorder x1 - User Manual x 1 - AC Adapter x 1 - Mouse x 1 - Terminal Block x 6 - IR Remote Control x 1 - Battery x 2 - HDD Fixing Bracket x 1 set - Power Cord x 1 - SATA cable x 1 - Screws x 4 for HDD - Screws x 2 for HDD fixing bracket - Shockproof rubber x 4 2
ページ9に含まれる内容の要旨
1.3 SPECIFICATIONS ECOR 264-4F2 ECOR 264-8F2 ECOR 264-4D2 ECOR 264-8D2 Video format PAL / CCIR Display format main monitor 1, 4x multiscreen, PiP 1, 4, 6, 8, 9x multiscreen, PiP 4 inputs 1 Vp-p composite PAL, BNC, 8 inputs 1Vp-p composite PAL, BNC, Video input automatic 75 Ohm termination automatic 75 Ohm termination 1 main monitor output, 1 Vp-p at 75 Ohm, BNC Video output 1 main monitor output VGA, 15-pin Sub-D Video compression H.264 Display resolution VGA output 1280 x 1024 /
ページ10に含まれる内容の要旨
Archive USB 2.0 interface, internal DVD-RW drive (only “D” models) Ethernet RJ-45 network connector 1 x RS-232 (9-pin Sub-D) (for service purpose only) Interfaces 1 x RS-485 screw terminal connector Password protection 3 levels Watchdog function for HDD status, HDD temperature, recording and HDD fault Power source 12 V DC, via included power supply 100 ~ 240 V AC Power consumption 40 W max. Ambient temperature 0°C ~ +40°C Dimensions (WxHxD) 320 x 54,3 x 208,9 mm Weight 4,0 kg (w/o H
ページ11に含まれる内容の要旨
1.4 FRONT PANEL Your primary interaction with your new DVR will be through the Front Panel buttons and their corresponding buttons on the included IR Remote Control. Take a moment to learn where the keys are as the remainder of the manual will refer to them often. 5 6 7 8 9 10 3 19 18 17 16 2 4 1 11 12 13 14
ページ12に含まれる内容の要旨
10) Menu: Press this key to enter/exit MAIN SETUP MENU. 11) Live: Press this key to show live view. Press to exit from playback mode. 12) View: Press this key to switch between 4x, PiP (Picture In Picture), full screen and 9x. Note: PIP display is not available in playback mode. Note: This key is also used for BNC and VGA selection at the initial setup. 13) SEQ: Press this key to enter the auto sequential switching mode. The sequence dwell time can be set in “Display Set
ページ13に含まれる内容の要旨
1.5 REAR PANEL During initial setup you will be connecting your DVR to multiple input and output devices. This is done through the rear panel. 1 3 2 4 5 6 7 8 9 10 Figure 1-2 Rear Panel 1 Video in Connect camera’s video output or other composite video source to the video input connection. 2 Alarm Out N.C
ページ14に含まれる内容の要旨
1.6 VIDEO INPUT / OUTPUT INSTALLATION Cameras and CCTV monitors must use copper center conductor/copper braid 75 Ohm video cable (e.g. RG-59, RG-6, RG-11) with BNC connectors. To avoid impedance mismatch and undesired loss/reflections, 50 Ohm coax cable (e.g. RG-58), or 75 ohm foil shield antenna cable and other types of coaxial cable are not compatible. All connected video sources must provide a 1 Vpp NTSC or PAL standard video signal. When converting other transmission types (twis
ページ15に含まれる内容の要旨
1.7 ALARM CONTACT INSTALLATION The alarm input can be used to start recording or for recording rate adjustment. In addition, alarm reactions such as camera display on the monitor, buzzer, e-mail and network alarm are available. The alarm output relay can be switched if required. Alarm input response actions can be controlled according to a flexible schedule. 1.7.1 Alarm Input Contacts This DVR provides one alarm input per camera. The input is programmable N.O. (Normal Open) or N.C. (
ページ16に含まれる内容の要旨
1.8 RS-485 KEYBOARD / PTZ INSTALLATION All functions can be remote-controlled by the EKB-500 universal keyboard. Using the EEPbus protocol, digital video recorders, keyboards and speed domes can be installed on one single RS-485 bus. One system can comprise up to 8 keyboards. 1.8.1 General RS-485 bus installation The EKB-500 keyboard uses a RS-485 simplex wiring; the signal is transferred via a single twisted pair line. CAT5 network cable is recommended, UTP version (unshielded) is suffi
ページ17に含まれる内容の要旨
A RS-485 distributor can also be used to increase the maximum number of devices on the bus as well as the total range. Each distributor output provides another RS-485 bus. This allows each output to extend an additional 1200m, and it also enables the additional connection of 31 further devices to each output (the output itself represents one device). The maximum system expandability depends on the RS-485 address range of the installed devices. System expansion with RS-485 signal dis
ページ18に含まれる内容の要旨
1.8.5 Speed Dome Installation Speed dome or telemetry receiver pan/tilt/zoom control is available through web browser or the optional PowerCon software if the DVR is connected to a network. Local telemetry control is provided by USB - mouse control or by the optional EKB-500 keyboard. Supported protocols: EverFocus, Pelco-D, Pelco-P, Samsung, Transparent Required DVR settings: RS-485 receiver address in CAMERA menu (Section 4.3) RS-485 parameters and protocol in the I/O CONTROL
ページ19に含まれる内容の要旨
1.10 NETWORK CONNECTION This section only describes physical connection to an Ethernet network. This step must be completed before the DVR can connect to the network. There are two basic types of connection: 1.10.1 Direct PC Connection through Crossover Network Cable The point-to-point connection of DVR and PC requires a crossover (crossed) network cable. This type of connection is ONLY used for direct connection to a single PC. Make sure that the PC is equipped with a 10/100 Mb
ページ20に含まれる内容の要旨
Figure 1-4 Network Connection through Patch Cable Pinout of straight patch cable 1.11 FINAL INSTALL PROCESS Once you have completed the basic wiring connections, you are ready to turn on the DVR. Simply plug in the power source. The POWER LED will light up if power is normal. Once the system has finished loading, you can begin to set up the menu options for the DVR. 14
