Silicon Image s1-2kの取扱説明書

デバイスSilicon Image s1-2kの取扱説明書

デバイス: Silicon Image s1-2k
カテゴリ: DVR
メーカー: Silicon Image
サイズ: 2.29 MB
追加した日付: 7/18/2013
ページ数: 38
説明書を印刷

ダウンロード

使い方は?

私たちの目的は、皆様方にデバイスSilicon Image s1-2kの取扱説明書に含まれたコンテンツを可能な限り早く提供することです。オンラインプレビューを使用すると、Silicon Image s1-2kに関してあなたが抱えている問題に対する解決策の内容が素早く表示されます。

便宜上

説明書Silicon Image s1-2kをこちらのサイトで閲覧するのに不都合がある場合は、2つの解決策があります:

  • フルスクリーン表示 – 説明書を(お使いのコンピュータにダウンロードすることなく)便利に表示させるには、フルスクリーン表示モードをご使用ください。説明書Silicon Image s1-2kのフルスクリーン表示を起動するには、全画面表示ボタンを押してください。
  • コンピュータにダウンロード - Silicon Image s1-2kの説明書をお使いのコンピュータにダウンロードし、ご自身のコレクションに加えることもできます。デバイス上のスペースを無駄にしたくない場合は、いつでもManualsBaseサイトでダウンロードすることもできます。
Silicon Image s1-2k 取扱説明書 - Online PDF
Advertisement
« Page 1 of 38 »
Advertisement
印刷版

多くの人々は画面表示ではなく印刷された説明書を読むほうを好みます。説明書を印刷するオプションも提供されており、上記のリンクをクリックすることによりそれを利用できます - 説明書を印刷。説明書Silicon Image s1-2kを全部印刷する必要はなく、選択したページだけを印刷できます。紙を節約しましょう。

要旨

次のページにある説明書Silicon Image s1-2kの内容のプレビューは、以下にあります。次のページにある説明書の内容をすぐに表示したい場合は、こちらをご利用ください。

内容要旨
ページ1に含まれる内容の要旨


SI-2K Image &
Software Install Manual




SiliconDVR
Version 1.1







December 2008


Part #25436
© 2008 Silicon Imaging, Inc Page 1

ページ2に含まれる内容の要旨

Table of Contents Section Page 1.0 - Introduction 3 1.1 Release Notes for SiliconDVR Version 1.1 3 2.0 SI-2K Maintenance Tool (SI-2K Recorder Use) 6 2.1 Download and Pre-installation 6 2.11 Downloading 4 2.12 Prepare the USB Drive 5 2.2 Before You Boot 9 2.3 Using the Maintenance Tool 10 2.4 Troubleshooting 12 13 2.5 Touchscreen Calibration & Drivers 3.0 SiliconDVR Installer (PC/Laptop Use) 14 3.1 - Minimum System Requirements 14

ページ3に含まれる内容の要旨

1.0 Introduction This manual covers the installation and update procedure for the following: • SI-2K Recorders using Maintenance Tool (Section 2) • PC/Laptop Systems with Software Installer (Section 3) The SI-2K Image installation uses a new SI-2K Maintenance Tool to update both SiliconDVR and the full operating system which resides on the internal Compact Flash. Once updated, no additional software or driver installation is required. This update procedure overwrites the entire int

ページ4に含まれる内容の要旨

1.1 Release Notes for SiliconDVR Version 1.1 Image Quality -Improved reliability in black calibration -Enhanced deviant pixel detection processes -Increased total count of Deviant pixels detected and corrected -Reduced column FPN in high-temp -Higher Quality Cineform Encoder Modes (3.5:1) Operational Reliability - Feedback system during camera connection or loading new mode - Greater stability when recording .SIV files to slow drives - Fix for short file Time-lapse s

ページ5に含まれる内容の要旨

SI-2K & Windows-XP Embedded Support tools - USB thumb-drive SI-2K Image Installer (Maintenance Tool) - New XP-e Write Filter (FBFW) used to prevent data writing to the compact flash card which contains the OS Image. Only the SiliconDVR data folder is accessible for storing .looks and preference settings. SI-2K Recorder: Known Issues & Limitations - SIV Playback on slow drives can hang: Use higher speed drives, Raid or SSD - High Speed CineForm modes (72/85/150P) will only

ページ6に含まれる内容の要旨

2.0 SI-2K Maintenance Tool (For SI-2K Recorders Only) The SI-2K contains a compact flash memory card that appears as the “C:” drive when the system is operating. The system boots and runs the SiliconDVR application from this drive. The SI-2K Maintenance Tool is provided to quickly upgrade or restore the system’s flash drive to a previous state, called a “snapshot”. This is an exact image of the full camera system – SiliconDVR application, drivers and operating system. As su

ページ7に含まれる内容の要旨

2.1 Download and Pre-installation If you have received the SI-2K Maintenance Tool already installed on a USB drive, you may skip to the section “2.2 Before You Boot” 2.1.1 Downloading The SI-2K Maintenance Tool is distributed in a single ZIP file that may be more than 1GB in size. Download this file and save it to a computer running Windows. The application used to prepare the drive for booting is not available for Mac OS at this time. Please contact support@siliconimaging.co

ページ8に含まれる内容の要旨

A warning message will appear as shown in Figure 2. Verify that the flash drive has been correctly identified, in this example it’s drive “F:”, and press ENTER to make the drive bootable. Figure 2 Use the “Safely Remove Hardware” function on the Windows Taskbar to insure that the drive is properly written prior to unplugging it. Please note that almost all recently manufactured flash drives from reputable manufacturers are compatible with the SI-2K’s booting process, but t

ページ9に含まれる内容の要旨

2.2 Before You Boot The Maintenance Tool is designed to modify only the internal flash drive, but it’s always prudent to make sure that any work you have on the SI-2K has been copied off the system prior to using the tool. You may also choose to remove the hard drive carrier from the SI-2K prior to booting with the Maintenance Tool. Customized “.LOOK” files are stored on the internal flash drive and will be overwritten during a snapshot restore. These must be copied off the system

ページ10に含まれる内容の要旨

2.3 Using the Maintenance Tool The Maintenance Tool interface is operated using the mouse on the side of the SI-2K (not via touchscreen). There are two types of flash media used in the SI-2K, Transcend and X4. Snapshot Images for both media types are provided in the Maintenance Tool and the appropriate image will be automatically selected. A brief description of the snapshot along with the date of its creation is shown. Press "Restore Snapshot" to begin. Then click the large butt

ページ11に含まれる内容の要旨

Once the restore operation has completed, which typically takes five to ten minutes, you will see a message reporting OPERATION IS FINISHED. Click the large button at the bottom “CLICK HERE TO COMPLETE” to begin the system shutdown and insure that data written to the internal flash drive is safely stored. Note: The option to cancel the process once a restore has started is not available. If the restore process is interrupted, the internal flash drive will be in a corrupted sta

ページ12に含まれる内容の要旨

2.4 Troubleshooting 2.4.1 BIOS SETTINGS IF BOOT FAILS If the SI-2K does not boot into the Maintenance tool, the BIOS boot settings may need to be adjusted. 1. Connect a USB Keyboard and a monitor to the VGA port (do not use the SI-2K Electronic Viewfinder) to the switched off camera. 2. Switch on the camera and press the "DEL" Button in order to enter the BIOS as soon as the camera gives you that option (during start up the first time you see information on your monitor)

ページ13に含まれる内容の要旨

2.5 Touchscreen Calibration & Drivers The flash drive of the SI-2K is protected from inadvertent writing by the File Based Write Filter (FBWF). This protection keeps the file system from being corrupted during unexpected shutdowns, such as when the battery runs down. In order to make changes to the system files, it is necessary to turn off this protection, make the changes and then re-enable the protection. While the FBWF is off, be sure that the camera cannot lose power and is alway

ページ14に含まれる内容の要旨

3.0 SiliconDVR Installer (For PC/Laptop Only) The installation instructions for installing SiliconDVR are split into two sets: One for Intel Pro1000 NIC-based systems, and a second set for other generic NIC’s systems not compatible with the Pleora High Performance Driver for Intel Pro1000 NIC’s (eg. Marvell Yukon). These installation instructions assume a clean install of SiliconDVR. If a previous version of SiliconDVR has been installed on the computer, follow the unin

ページ15に含まれる内容の要旨

3.2 Installing SiliconDVR for Pro1000 NIC’s: 1. Certify that the Pro1000 NIC being used for SiliconDVR has the Intel Pro1000 NIC driver software installed and the NIC can operate as a “normal” NIC, capable of receiving normal TCP/IP network traffic such as email, internet, file-sharing, etc. 2. Open the SiliconDVR Installer. You will be greeted by the installer splash-screen. Press the “Next” button. 3. When you reach the “Select Components” screen, make sure that all thre

ページ16に含まれる内容の要旨

5. After SiliconDVR is installed, the CineForm installer will launch. Click though the “next” button and then when you arrive at the install screen, press the “Install” button. 6. After the CineForm Installer completes, the Pleora iPort Vision Suite will being installation. Click the “Next” button. 7. Under the “Setup Type” window select the “Complete” choice for installation. © 2008 Silicon Imaging, Inc

ページ17に含まれる内容の要旨

8. Once the iPort Vision Suite has completed installing, the Pleora eBUS driver Suite will launch. Click though the “Next” button until the driver is completed installing. 9. After the eBUS driver has completed installation, the installer will go back to the SiliconDVR installer splash-screen. 10. Once the SiliconDVR installer has completed, you will be prompted to reboot the computer. 11. Restart the computer. © 2008 Silicon Imaging, Inc

ページ18に含まれる内容の要旨

12. Installing Drivers: After rebooting the computer, go into \Program Files\Pleora Technologies Inc\Ethernet Bus\Binaries\ and launch the EbDriverTool.exe. 13. Once inside the EbDriverTool, you should see the active NIC on the computer available for installing the eBUS drivers on for use with SiliconDVR. It should be listed as “NIC Driver” under the “Driver” field. 14. Click on the Intel Pro 1000 NIC that will be used with SiliconDVR, and then click on the “Configure”

ページ19に含まれる内容の要旨

16. After the driver installs, close the configuration window. 17. The NIC in the main EbDriverTool window should now read “High Performance Driver” in the driver field. 18. Quit the EbDriverTool application and then reboot the computer 19. After reboot, launch SiliconDVR. © 2008 Silicon Imaging, Inc Page 19

ページ20に含まれる内容の要旨

3.3 Installing SiliconDVR for Generic NIC’s: As a pre-installation procedure to optimize the generic NIC and set IP Addresses for use with SiliconDVR, follow these procedures: 1. Go into the Network Connections dialog box by right-clicking on Network Neighborhood and going to “properties”. 2. Right-click on the “Local Area Connection” and go to “properties”. 3. Turn off the “Client for Microsoft Windows”, “QoS Packet Scheduler”, “File and Printer Sharing”, and on Windows Vist


類似の説明書
# 取扱説明書 カテゴリ ダウンロード
1 Sony DIRECTV RECEIVER SAT-W60 取扱説明書 DVR 1
2 Sony DCR-TRV75 取扱説明書 DVR 7
3 Sony DSR-1800 取扱説明書 DVR 83
4 Sony BKDW-514 取扱説明書 DVR 2
5 Sony BKDW-509 取扱説明書 DVR 4
6 Sony DSR-1500AP 取扱説明書 DVR 79
7 Sony DHG-HDD250 取扱説明書 DVR 0
8 Sony DSR-1800P 取扱説明書 DVR 39
9 Sony DCR-IP5/IP7BT 取扱説明書 DVR 1
10 Sony DVW-2000P L 取扱説明書 DVR 0
11 Sony DAV-D150G 取扱説明書 DVR 5
12 Sony ICD-P520 取扱説明書 DVR 18
13 Sony HVR-A1N 取扱説明書 DVR 136
14 Sony MAV-555SS 取扱説明書 DVR 6
15 Sony HANDYCAM HDR-FX1000E 取扱説明書 DVR 3