ページ1に含まれる内容の要旨
User’s manual for MPEG4 DVR
Model QSNDVR9M and QSNDVR16M
*This manual is for MPEG4 QSNDVR9M 9-channel and QSNDVR16M 16-channel digital video recorder
And uses the 16-channel digital video recorder as example.
Before operation, we strongly advise that you read
ページ2に含まれる内容の要旨
Table of Contents Digital Video Recorder (DVR) Introduction ..................................................................................................... 4 1.1 Product introduction .......................................................................................................................... 4 1.2 Features of this DVR .......................................................................................................................... 4 Installation Notice ..........
ページ3に含まれる内容の要旨
3.2.1 SETUP-SYSTEM .................................................................................................................. 34 3.2.2 SETUP-LIVE ......................................................................................................................... 39 3.2.3 SETUP-REC ......................................................................................................................... 42 3.2.4 SETUP-STORAGE .......................................................
ページ4に含まれる内容の要旨
Digital Video Recorder (DVR) Introduction 1.1 Product introduction This DVR is designed specially for CCTV system. It uses an embedded processor and embedded operating system working with the high-powered code and decode chip. In addition, it uses advanced IT technology to make the system more stable, such as the audio code and decode technology, large capacity hard
ページ5に含まれる内容の要旨
Format Standard MPEG-4 compression format Storage Supports up to four IDE Hard Drives simultaneously (Or three IDE HDDs and one IDE DVD-RW/CD-RW) Backup Auto-play software automatically packed in backup files, and Auto-water-mark check in backup files to assure files’ authenticity Support backup via USB 2.0 to USB flash memory, or CDRW, DVD-RW to CD-R/DVD-R respectively Support remote backup by “Net Client” through LAN or internet Record and playback Record modes: M
ページ6に含まれる内容の要旨
Alarm 9/16 alarm inputs and 4 alarm outputs, TTL alarm output PTZ control Supports decoder which communicates with RS485 Supports speed dome Supports PTZ through network Communication port RS 485 equipped Network Supports TCP/IP protocol Supports wide bandwidth network through modem (PPPOE) Supports static IP and dynamic IP (DHCP) Real time preview/playback/monitoring with audio signal through network Supports control PTZ camera through the netw
ページ7に含まれる内容の要旨
Installation Notice Attention: Before connecting to other equipment, please make sure the device is powered off. Do not hot plug in! 2.1 Checking the contents Check the contents when you receive the unit, to make sure you have all the parts. Normally it will contain: a remote control, a power cable, a CD-Rom with “Net Client” software, screws for installing HDDs 2.2 Installing the Hard Drive 2.2.1 Install reminder Please confirm the size of HDDs needed and c
ページ8に含まれる内容の要旨
2.2.2 Install tool One Phillips screwdriver 2.2.3 Install process Open the DVR using screwdriver Set one HDD as master and the other as slave if two HDDs are connected to one ATA interface!!! Attention: Hard Drives connected to the same parallel cable can not be set as master+master or slave+slave, they must be master+slave!!! HDD setup: Using a Maxtor Hard Drive (DiamondMax Plus 8 ATA/133 40GB) as example. Read the jumper diagram on the rear of HDD No jumper=DS(SLAVE)
ページ9に含まれる内容の要旨
ページ10に含まれる内容の要旨
Jumper area The picture blow is the IDE connection/Power connection section of the HDD. Jumper area Jumper according to the diagram above SLAVE MASTER The sequence of read/write data from HDD The ATA interface which is near the motherboard center is the secondary interface, the next ATA interface which is near the motherboard edge is the primary interface. The sketch is in the following. The H
ページ11に含まれる内容の要旨
Primary ATA interface is HDD A, the slave is HDD B. The master HDD connected to secondary ATA interface is HDD C, the slave is HDD D. The record sequence is: HDD A→HDD B→HDD C→HDD D Overwrite sequence: The sequence is irrespective of HDD. The DVR overwrites HDD from the oldest record file when HDD is full. Motherboard Operation Put the HDD into the HDD fixation rack. If the user wants to install mo
ページ12に含まれる内容の要旨
19 pins are in the other row). Make sure pins are plugged into interface correctly. Connect the power supply to HDD Sketch map of installation Close the device cover and lock it with screws Attention: Please format the HDD before using. If the user wants to connect the CD/DVD driver to the ATA interface, please choose the secondary interface, that is near the center of the motherboard. Furthermore, the CD/DVD driver must be set as master, and the HDD whi
ページ13に含まれる内容の要旨
1 2 Second, attach the HDD by tw o screw s on both Fir st, put the HDD into the HDD fixation rack sides 4 3 Third, connect the HDD cable Fourth, connect the pow er supply to HDD Sketch of installation Page 15 x
ページ14に含まれる内容の要旨
2.3 Back panel and interface terminals Attention: The real connections on the back panel might be slightly different from the sketch below. 2.3.1 Back panel of 16-channel DVR ALARM OUT CAM1 ALARM IN CAM2 CAM4 CAM7 CAM3 CAM5 CAM6 CAM8 AUDIO IN 1 AUDIO IN 2 1 2 3 4 1 2 5 7 3 4 6 8 CAM9 CAM10 CAM11 CAM 12 CAM13 CAM15 CAM16 CAM1 4 AUDIO IN 4 AUDIO IN
ページ15に含まれる内容の要旨
1 Video input 1-16 2 Spot output 3 Video output 4 S video output 5 Audio output Page 17
ページ16に含まれる内容の要旨
6 LAN port 7 Audio in 1-4 8 Alarm input1-16 9 Alarm output Page 18
ページ17に含まれる内容の要旨
10 Fan vent 11 Power plug 12 USB port 13 VGA port 14 RS 232 port Null 15 RS485 port Page 19
ページ18に含まれる内容の要旨
2.3.2 Back panel of 9-channel DVR ALARM OUT ALA RM IN AUD IO IN 1 AUDIO IN 2 CA M 1 CA M 5 CAM 7 1 2 3 4 CAM 3 CAM 9 5 1 2 3 4 6 7 8 9 CA M 4 CAM 2 CA M 6 CAM 8 AUD IO IN 3 AUDIO IN 4 VI DEO OUT S VID EO AUD IO OU T SPO T OUT GND COM + - RS- 4 85 LAN RS- 2 32 VG A USB Back panel of 9-channel DVR The difference between 9-channel and 16-channel is the 9-channel has 9 video i
ページ19に含まれる内容の要旨
2.4 Front panel and interface terminals Attention: The actual buttons on the front panel please might be slightly difference from this sketch. 14 1 28 11 15 13 LED 2 P T 1 3 27 12 5 4 26 6 Z/F 16 23 7 8 9 AUDIO 7 0 MODE B ACKUP SEAR CH STO P REC PLAY FF REV 17 Power MENU FUNCTION INFO R USB 21 22 25 2 19 18 4 5 6 8 9 10 20 24 Number Icon Description Number Icon Description Number Ic
ページ20に含まれる内容の要旨
7 Zoom/Focus 8 Audio on/off button control 9 Backup button 10 Menu button 11 Function button 12 Status button 13 Move Left 14 Move Up 15 Enter button 16 Move Right 17 Move down 18 Record button 19 Shuttle: to control 20 Shuttle: to control the the DVR to play playback speed the record frame by frame. 21 Search button 22 Play button
