ページ1に含まれる内容の要旨
DX8100-EXP
Expansion Unit
Installation Manual
C2636M-B (4/07)
Digital Video Recorder
DX8100
ページ2に含まれる内容の要旨
ページ3に含まれる内容の要旨
Introduction Welcome to the DX8100-EXP Expansion Unit upgrade for the DX8100 Series digital video recorder (DVR). This document serves as a guide for installing the DX8100-EXP Expansion Unit. If you ordered the DX8124 or DX8132 model DVR, the optional Capture Card and DX8100 I/O card are already installed. Use the Expansion cable to connect the Expansion Unit to the DX8100. For information about connecting the DX8100 Expansion Unit to the DX8100 DVR, refer to Co
ページ4に含まれる内容の要旨
Table A describes the additional capacity that the DX8100-EXP Expansion Unit upgrade adds to the base model DX8100. Table A. DX8100 Expansion Unit Upgrade Features DX8108 Configuration DX8116 Configuration Feature Base Unit With Expansion Unit Base Unit With Expansion Unit Camera inputs 8 24 16 32 Alarm inputs 8 24 16 32 ATM/POS 8 24 16 32 Relay outputs 8 16 16 24 PARTS LIST In addition to this document, Table B lists the components that are included in the DX8100-EXP Expansion Un
ページ5に含まれる内容の要旨
TOOLS NEEDED Table C. DX8100 Expansion Unit Kit Items Qty Description 1 Phillips screwdriver #1 (nonmagnetic) 1 Properly grounded ESD wrist strap and mat 4 Small containers for storing screws (optional) OTHER DX8100 OPTIONAL ACCESSORIES The DX8108 base unit comes with an 8-channel Capture Card and the DX8116 base unit includes a 16-channel Capture Card. When considering adding the audio option: • The DX8108-AUD audio card is installed on the 8-channel Capture Card. The DX810
ページ6に含まれる内容の要旨
Getting Ready Before you install the DX8100-EXP Expansion Unit, familiarize yourself with the instructions throughout this manual. The Expansion Unit is ready to use after you complete the installation steps in this manual. The steps to install the Expansion Unit are summarized as follows: 1. Unpack the DX8100-EXP Expansion Unit kit and check that you have all the necessary Expansion Unit kit components. For information about components supplied in the DX8100-EXP Expansion Un
ページ7に含まれる内容の要旨
6. Ensure that the DX8100 Series DVR and all of its components are protected against electrostatic discharge (ESD). Before handling any electronic components, you should take steps to ground yourself properly so that any built-up static electric charges are dissipated away from the unit. The most effective method for combating ESD is to use a properly grounded wrist strap. NOTE: If you do not have access to a grounded wrist strap, you can discharge any built-up static by periodicall
ページ8に含まれる内容の要旨
Prepare DX8100 for Expansion Unit Installation This section describes how to access the DX8100 interior. For information about mounting the DX8100 in a rack, refer to the DX8100 Installation Manual. OPEN THE DX8100 CHASSIS If the DX8100 is mounted in a rack, it must be removed. Two people might be required to lift and remove the DX8100. To move the DX8100 to an area that will provide full access to the unit chassis: WARNING: Make sure unit is turned off and you are wearing a pr
ページ9に含まれる内容の要旨
COMPONENT LAYOUT Figure 7 shows the slots and the DX8100 Series DVR’s major components. Some detail is removed from the illustrations in this manual for the purpose of clarity. (Slots on the motherboard are labeled differently.) REAR OF DVR FRONT OF DVR Figure 7. DX8100 Interior Table E describes the DX8100’s slot assignments and major components. Table E. DX8100 Slot Assignments and Major Components Item Description Item Description Slot 1: PTZ card installed in PCI connector
ページ10に含まれる内容の要旨
Install the DX8100 I/O Card The DX8100 I/O card comes in a separate box that contains the DX8100 I/O card and two cables: a 5-pin alarm and relay cable and a 32-pin video input ribbon cable. For information about the other DX8100 Expansion Unit kit components, refer to Parts List on page 4. The I/O card is installed in slot 7 and does not insert into a slot on the motherboard. The DX8100 I/O card receives power from the DX8100 and provides power for the DX8100 Expansion Unit. F
ページ11に含まれる内容の要旨
To install the DX8100 I/O card in slot 7: 1. Remove the Rear Cross Brace. Refer to item 14 in Figure 7 on page 9. 2. Do the following: a. Remove the slot cover for slot 7 and retain the screw. b. Insert the DX8100 I/O card into the slot 7 opening and secure the I/O card bracket with the screw. c. Insert the 4-wire DX8100 power plug into the I/O card power connector CN302. d. Insert the 5-pin Alarm and Relay cable into the DX8100 I/O card Alarm and Relay connector CN303. The other end
ページ12に含まれる内容の要旨
Installing the Capture Card This section describes how to install the DX8100 Capture Card. The Capture Card installation is performed after you have installed the DX8100 I/O card. The DX8100 Capture Card comes in a separate box that contains the Capture Card and one 14-pin interconnect cable. For information about the other DX8100 Expansion Unit kit components, refer to Parts List on page 4. The optional Capture Card is installed in PCI slot 3, and supports the additional 16 BNC
ページ13に含まれる内容の要旨
To install the optional Capture Card: 1. On the main Capture Card, remove the 7-wire TV/Audio cable and lay the cable over the DX8100 I/O card. Refer to callout 2c in Figure 11 for the location of the TV/Audio cable. 2. Do the following: a. Remove the slot cover for slot 3 and retain the screw. b. Place the optional Capture Card under the 5-wire Alarm and Relay cable from the main Alarm and Relay I/O board and firmly seat the card in the PCI slot 3 connector, and then secure the Capture
ページ14に含まれる内容の要旨
Reassemble the Unit To reassemble the DX8100: 1. Replace the chassis cover using the same screws you removed from the side and rear of the unit. Refer to Figure 12. Figure 12. Replacing Chassis Cover 2. Attach the silver part label that came in your upgrade kit to the inside of your DVR’s front door. a. Remove the paper backing from the part label. b. Carefully place the label, adhesive-side down, on a free section of the inside of the door. c. Press down firmly to ensure that the l
ページ15に含まれる内容の要旨
Connecting the Expansion Unit to the DX8100 This section describes how to connect the Expansion Unit to the DX8100. The Expansion Unit can be rack mounted, positioned to the side, or set on top of the DX8100. Figure 14 shows how to assemble the rack mount kit. Figure 14. Assembling Expansion Unit Rack Mount Kit Table H describes the items included in the Expansion Unit rack mounting kit. The Expansion Unit mounting dimensions are as follows: • Desktop: 1.73 (H) x 17 (W) x 8.1
ページ16に含まれる内容の要旨
To connect the Expansion Unit to the DX8100 DVR: 1. Do one of the following: • Desktop mounting: Set the Expansion to the side or on top of the DX8100. • Rack mounting: Attach the rack mount kit and install the Expansion Unit in the rack enclosure directly above the DX8100. 2. Connect the 50-pin Expansion cable end (partially shown in Figure 15) to the Expansion Unit connector, and then connect the 50-pin Expansion cable end to DX8100 I/O card. 3. Plug the power cord back into the
ページ17に含まれる内容の要旨
4. Power on the DX8100. Figure 16. Restarting the Unit 5. Log in to the DX8100 and verify that the additional devices are displayed in the DX8100 site tree. For information about the additional features provided by the Expansion Unit, refer to Table A on page 4. 6. This completes the Expansion Unit installation process. The DX8100 DVR does not have to be powered down to connect devices to the Expansion Unit. To connect devices to the Expansion Unit: 1. Power down the Expansion Unit by di
ページ18に含まれる内容の要旨
REVISION HISTORY Manual # Date Comments C2636M 11/06 Original version. C2636M-A 3/07 Added Expansion Unit rack mount dimensions and revised DX8108-AUD/DX8116-AUX text. C2636M-B 4/07 Corrected the reference to the Expansion cable from 68- to 50-pin. Pelco, the Pelco logo, Camclosure, Esprit, ExSite, Genex, Legacy, and Spectra are registered trademarks of Pelco. ©Copyright 2007, Pelco. All rights reserved. Endura and Spectra III are trademarks of Pelco. DLP is a registered trademark of Texas
ページ19に含まれる内容の要旨
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 material or workmanship for a period of one year after the date of shipment. or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following information: Exceptions to this warranty are as noted below: 1. Model and serial number •
ページ20に含まれる内容の要旨
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates | United Kingdom | United States
