ページ1に含まれる内容の要旨
DVAA Series Disk Array
for DVR1 Series
Digital Video Recorder
Eng
Philips
Communication,
Security & Imaging
Installation Instructions
ページ2に含まれる内容の要旨
Warning! To prevent fire and electronic shock, do not expose this product to rain or moisture. The lightning flash with the arrowhead The exclamation point, within an equilateral symbol, within an equilateral triangle, is triangle, is intended to alert the user to the intended to alert the user to the presence of presence of important operating and uninsulated “dangerous voltage” within the maintenance (servicing) instructions in the products enclosure that may be of sufficient literat
ページ3に含まれる内容の要旨
1 Installation.......................................................................3 1.1 Product Description........................................................................................3 1.2 Unpacking........................................................................................................3 1.3 Installation Environment................................................................................3 1.4 Rear Panel Diagram...........................................
ページ4に含まれる内容の要旨
1 Installation 1.1 Product Description The DVAA is a large, economical, hard drive based storage/archive device. It is available with 4 hard disk drives (model DVAA0412) or 8 hard disk drives (model DVAA0812). The DVAA0412 unit can later be repopulated with additional hard drives. 1.2 Unpacking Check the package and contents for visible damage. If any components are damaged or missing, do not attempt to use the unit. Contact the supplier immediately. If the unit must be returne
ページ5に含まれる内容の要旨
1.4 Rear Panel Diagram 1 2 3 4 5 6 7 8 Rear Panel Elements 1. Cooling Fan: Do not obstruct. 2. Power Connector, Voltage Selector and On/Off Switch 3. IEEE-1394 Firewire Ports 1 and 2* 4. 10/100 Ethernet Port* 5. SCSI Ports 1 and 2 6. Dip Switches* 7. RS-232 Port 8. Alarm Out Relay Connection* 1.5 Connections NOTE: * The Ethernet, Aux dip switch, Alarm output and IEEE-1394 Firewire ports are reserved for future upgrade. SCSI Ports 1 and 2 Connect to either SCSI port. Using
ページ6に含まれる内容の要旨
DB-9 Pin Configuration For RS-232 Port Pin Use Pin Use 1 DCD 6 Not Connected 2 RX 7 RTS 3 TX 8 CTS 4 Not Connected 9 Not Connected 5 Ground 1.6 Power-Up Select the correct voltage before supplying power to the unit. Use the voltage selector switch located on the rear panel of the unit, between the power connector and the On/Off Switch. Caution: Applying incorrect voltage could damage unit. Once the correct voltage has been selected and all connections have been made,
ページ7に含まれる内容の要旨
Hard Drive Activity Indicators (Red Lights) The light blinks when the drive is being accessed (read or write). Ethernet Indicators Reserved for future use. LCD Display Once power-up is complete, the LCD will display the total disk storage capacity of the unit. Key Pad Reserved for future use. 6
ページ8に含まれる内容の要旨
2 DVAA/DVR1 Installation The Philips DVAA Disk Array is only compatible with the DVR1 series digital video recorder. 2.1 Connecting to the DVR1 1) Connect the SCSI cable from the DVR1 to the DVAA series disk array. 2) Apply Power to the DVAA and wait 20 seconds 3) Apply Power to the DVR1 2.2 Configuring the DVR1 1) Configure the DVR1 Background Archive to ON (ARCHIVE SETUP > BACKGROUND ARCHIVE > ON) 2) Configure the DVR1 Archiving Overwrite mode for Continuous Overwrite (ARCHIVE SE
ページ9に含まれる内容の要旨
3. Before restoring archive data from the disk array (searching the disk array’s indexes), the DVR1 must stop recording. 3 Adding Hard Drives This section is required if your unit was shipped without hard drives installed, or if the user needs to replace a faulty drive. Caution: Do not allow any metal object to contact the motherboard. Do not allow loose screws to become lost inside the DVAA chassis. Wear an Electro Static Discharge protection device any time work is being performed i
ページ10に含まれる内容の要旨
Motherboard Overview Power Supply Load Resistors Jumpers IDE IDE Power Connectors Connectors 3.3 Mounting The Hard Drives First remove the hard drive support bracket. Orient the hard drive so that the IDE Power Connector is near the bottom of the chassis and facing the motherboard. Populate the drive array in order, starting from the left. Fasten the drive in place using the supplied screws. Fasten each drive using two screws through the bottom of the chassis. Attach the Hard Drive S
ページ11に含まれる内容の要旨
3.5 Connecting Hard Drives Use an IDE cable to connect drives as shown in the previous diagram. When attaching the IDE connector, make sure the connectors are oriented properly. Connecting To The Motherboard The red stripe on the connection ribbon should connect nearest the Pin 1 indicator Pin 1 Indicator on the motherboard. Connecting To The Hard Drive The red stripe on the connection ribbon should connect near the jumpers on the hard Pin 1 Near Jumpers drive. 3.6 Powering Hard D
ページ12に含まれる内容の要旨
3.7 Compatible Hard Drives The following is a list of hard drives that are compatible with the DVAA series disk array. Maxtor Drives Model Part Number Size Vulcan 4W030H2 30GB Vulcan 4W100H2 100GB Romulus 4D120J6 120 GB Galaxy 4K040H2 40GB Galaxy 4K080H2 80GB IBM Drives Model Part Number Size IBM 07N3925 30GB IBM 07N3935 75GB 11
ページ13に含まれる内容の要旨
4 Warranty This product offers a 3year warranty. The warranty does not cover hard drives not installed by the factory and does not cover damages that may occur due to improper hard drive installation. 5 Factory Service Refer all Service to qualified personnel. Contact the local Philips representative for service. Service Centers: USA: Ph: 800-366-2283 Central & S. America: 805-967-7917 (fax: 800-366-1329) (e-mail: philipscsirma@mdtglobal.com) Canada: 514-738-2434 (fax:
ページ14に含まれる内容の要旨
3935 890 41711 02-19 © 2002 by Bosch Security Systems, Inc. All Rights Reserved. Philips ® is a registered trademark of Philips Electronics N. A. Corp. Data subject to change without notice
