ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 95-6511
APPLICATIONS
Chrysler
Aspen 2008-09/Sebring 2007-10
Town and Country 2008-10/300/300c 2008-10
Dodge
Avenger 2007-10/Caliber 2009-10/Challenger 2009-10
Charger 2008-10/Dakota 2008-10/Durango 2008-09
Grand Caravan 2008-10/Journey 2009-10*
Magnum 2008-09/ Nitro 2007-10/Ram 1500 2009-11/Ram 2500/3500 2010-11
Jeep
Compass 2009/Commander 2008-10/Grand Cherokee2008-10/Patriot 2009
Liberty 2008-10/Wrangler 2007-10*
*(Modifications to radio cavity required)
Mits
ページ2に含まれる内容の要旨
95-6511 TABLE OF CONTENTS Dash Disassembly - Chrysler Aspen 2008-2009/Dodge Durango 2008-2009 . . . . . . . . . . .. . . 1 - Chrysler Sebring 2007-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 2 - Chrysler Town and Country 2008-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . .3,4 - Chrysler 300/300C 2008-2010 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 - Dodge Avenger 2007-2010 . . . . . . . . . .. . . . . . . . . . . . . . . . . .
ページ3に含まれる内容の要旨
1 2 3 4 5 6 4 1 2 3 5 6 95-6511 DASH DISASSEMBLY CHRYSLER ASPEN 2008-2009 DODGE DURANGO 2008-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short POWER OUTLET circuit. 2 Unsnap and remove storage cup holder assembly. (Figure A) 3 Remove (2) screws from bottom edge of center dash trim panel. Unsnap and remove the panel. (Figure B) 4 Remove (4) screws securing the B radio. Unplug and remove radio. 12 (Figure C) 9 3 6 Continue to kit assembly. POWER OUTLET C 12 9 3 6
ページ4に含まれる内容の要旨
95-6511 DASH DISASSEMBLY CHRYSLER SEBRING 2007-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip entire panel surrounding radio including a/c vents and clock. Unplug and remove panel. (Figure A) 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. (Figure B) B Continue to kit assembly. 2
ページ5に含まれる内容の要旨
95-6511 DASH DISASSEMBLY CHRYSLER TOWN AND COUNTRY 2008-2010 DODGE GRAND CARAVAN 2008-2010 A Disconnect the negative battery ter- 1 minal to prevent an accidental short circuit. 2 Remove (2) screw covers facing up above radio then remove the (2) Phillips screws exposed. (Figure A) 3 Lift up on panel above radio then remove (2) Phillips screws exposed at front edge of radio trim panel. (Figure B) B 4 Remove (3) plastic push pins per side of bottom trim panel then slide panel toward rear of van to
ページ6に含まれる内容の要旨
95-6511 DASH DISASSEMBLY CHRYSLER TOWN AND COUNTRY 2008-2010 DODGE GRAND CARAVAN 2008-2010 D 5 Remove (2) Phillips screws exposed at bottom edge radio trim panel. (Figure D) 6 Unclip and remove entire panel sur- rounding radio including climate con- trols, vents and clock. (Figure E) 7 Remove (4) Phillips screws securing radio. (Figure F) Continue to kit assembly. E F U SEEK SEEK SCAN TIME INFO RW FF PUSH ON PUSH AUDIO/SELECT AM LIST MUSIC FM TYPE DISC SEL;ECT VOLUME TUNE/SCROLL AUX SET 12 3
ページ7に含まれる内容の要旨
1 2 3 4 5 6 95-6511 DASH DISASSEMBLY CHRYSLER 300/300C 2008-2010 DODGE MAGNUM 2008-09/CHARGER 2008-10 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unsnap and remove center dash trim panel. (Figure A) 5 1 2 3 4 6 3 Remove (4) screws securing the radio. Disconnect and remove the radio. (Figure B) Continue to kit assembly. B 5
ページ8に含まれる内容の要旨
95-6511 DASH DISASSEMBLY DODGE AVENGER 2007-2010 A Disconnect the negative battery ter- 1 minal to prevent an accidental short circuit. 2 Unclip and remove the center console trim panel. (Figure A) 3 Unclip the center dash trim panel. (Figure B) 4 Remove (4) screws securing the radio. Disconnect and remove the B radio. (Figure C) 5 Remove (3) screws securing the radio rear support bracket and remove the bracket. (Figure D) Continue to kit assembly. C D U SEEK SEEK SCAN TIME INFO RW FF PUSH ON PU
ページ9に含まれる内容の要旨
95-6511 DASH DISASSEMBLY DODGE DAKOTA 2008-2010 A Disconnect the negative battery ter- 1 minal to prevent an accidental short circuit. 2 Unclip and remove the trim panel surrounding the radio. (Figure A) 3 Remove (4) Phillips screws securing B the radio. (Figure B) U SEEK SEEK SCAN TIME INFO RW FF Continue to kit assembly. PUSH ON PUSH AUDIO/SELECT AM LIST MUSIC FM TYPE DISC SEL;ECT VOLUME TUNE/SCROLL AUX 3 5 SET 12 4 6 AUX MITSUBISHI RAIDER 2008-09 A 1 Disconnect the negative battery ter- m
ページ10に含まれる内容の要旨
95-6511 DASH DISASSEMBLY DODGE NITRO 2007-2010 JEEP LIBERTY 2008-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip entire panel surrounding radio and climate controls, including a/c 5 6 3 4 1 2 vents. Unplug and remove panel. (Figure A) 3 Remove (4) 7MM screws securing radio. Unplug and remove radio. (Figure B) B Continue to kit assembly. 5 6 3 4 1 2 8
ページ11に含まれる内容の要旨
95-6511 DASH DISASSEMBLY DODGE JOURNEY 2009-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. OFF 2 Unclip and remove the entire factory radio trim panel including the a/c PUSH PUSH PUSH controls. (Figure A) PUSH ON PUSH AUDIO/SELECT AM LIST TIP: Open the compartment door at the MUSIC FM TYPE VOLUME DISC SEL;ECT TUNE/SCROLL AUX SET 12 3 4 5 6 AUX top of the radio trim panel. OUTLET POWER OUTLET 3 Remove (4) 7MM screws securing radio to dash to remove. (F
ページ12に含まれる内容の要旨
95-6511 DASH DISASSEMBLY JEEP COMMANDER/GRAND CHEROKEE 2008-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unsnap and remove the small trim around the console shifer. (Figure A) 3 Unsnap and remove the larger trim around the console shifter. (Figure B) 4 Remove one Phillips screw from inside the small storage pocket in the B lower dash, between the power outl- lets. (Figure C) 5 Unsnap and remove the dash panel from around the radio (including cli-
ページ13に含まれる内容の要旨
95-6511 DASH DISASSEMBLY JEEP WRANGLER 2007-2010 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 1 2 3 4 5 6 2 Unclip and remove the lower center trim below a/c controls. (Figure A) 3 Remove (2) Phillips screws exposed behind lower center panel. (Figure A) 4 Unclip and remove the upper center trim starting towards the rear of the B panel. (Figure A) 5 Remove (2) Phillips screws exposed behind upper center panel. (Figure A) 6 Unclip and remove entire panel s
ページ14に含まれる内容の要旨
95-6511 DASH DISASSEMBLY DODGE CALIBER 2009-10 DODGE CHALLENGER 2009-10 JEEP COMPASS 2009 JEEP PATRIOT 2009 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and move shifter trim to the side. 2 (Figure A) 3 Unsnap center dash trim panel (do not remove until climate controls are removed). (Figure A) 4 Remove (4) Phillips screws holding cli- mate control panel to backside of the center dash panel. 5 Remove (4) 7MM screws securing radio. Unplug and remove
ページ15に含まれる内容の要旨
115V AC 150W 95-6511 DASH DISASSEMBLY DODGE RAM 1500 2009-11 DODGE RAM 2500/3500 2010-11 A 1 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (1) T25 Torx screw in the compart- 2 ment next to the cup holders. (Figure A) 3 Remove (2) Phillips screws in the pocket below the climate control in the front of the center console. (Figure B) B 4 Remove (2) 9/32” screws in the cup holders. (Figure C) 5 Push down on the collar below the shifter then pull the shif
ページ16に含まれる内容の要旨
115V AC 150W 115V AC 150W 95-6511 DASH DISASSEMBLY DODGE RAM 1500 2009-11 DODGE RAM 2500/3500 2010-11 7 Unclip and remove the trim panel from the F accessory socket on the radio trim panel, then remove (1) T25 Torx screw. (Figure F) 8 Remove (2) T25 Torx screws from the top of the radio trim panel. (Figure G) 9 Unclip and remove the entire radio trim panel including the climate controls. (Figure H) Remove (4) 9/32” screws securing the 10 radio. (Figure I) Continue to kit assembly. G H I 14
ページ17に含まれる内容の要旨
95-6511 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets/trim plates to the Double DIN Radio using the screws supplied with the Radio. (Figure A) Continue to final assembly. STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets/trim plates to the stacked ISO units using the screws supplied with the units. (Figu
ページ18に含まれる内容の要旨
95-6511 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse
ページ19に含まれる内容の要旨
95-6511 NOTES 17
ページ20に含まれる内容の要旨
95-6511 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 12/10/10 © COPYRIGHT 2009-10 METRA ELECTRONICS CORPORATION INST95-6511
