ページ1に含まれる内容の要旨
INSTALLATION INSTRUCTIONS FOR PART 95-5810
APPLICATIONS
LINCOLN Town Car
2003-2011
95-5810
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate B) Double DIN Brackets
A
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-5520 - Ford harness 2003-up
• 70-5521 - Ford amp harness 2003-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Socket Set
1-800-221-0932
ページ2に含まれる内容の要旨
95-5810 TABLE OF CONTENTS Dash Disassembly - LINCOLN Town Car 2003-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the
ページ3に含まれる内容の要旨
60 70 50 80 40 100 90 30 60 140 100 20 20 110 10 180 120 0 MPH MILES H RN 2 1 C P 0.0 95-5810 DASH DISASSEMBLY LINCOLN TOWN CAR 2003-2011 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Remove (2) 7mm bolts facing upward above instrument cluster/gauges. (Figure A) 3 Carefully unsnap and remove dash panel surrounding radio and instru- ment cluster/gauges. (Figure B) B C 4 Remove (2) 7mm bolts above clock panel and remove panel). (Figure C) 5 Remove (4) 7m
ページ4に含まれる内容の要旨
95-5810 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets to the aftermarket radio using the screws supplied with the radio. (Figure A) 2 Place the Double DIN trim plate over the radio face then secure the entire assembly into the sub dash. (Figure B) Continue to final assembly. B 2
ページ5に含まれる内容の要旨
95-5810 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the Double DIN brackets to the aftermarket units using the screws supplied with the units. (Figure A) 2 Place the Double DIN trim plate over the unit faces then secure the entire assembly into the sub dash. (Figure B) Continue to final assembly. B 3
ページ6に含まれる内容の要旨
95-5810 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse
ページ7に含まれる内容の要旨
95-5810 NOTES 5
ページ8に含まれる内容の要旨
95-5810 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 11/18/10 © COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION INST95-5810
