ページ1に含まれる内容の要旨
Electric Bed Lift
Assembly Instructions
Treker 4200/4400 ST / NT & 4210/4410 ST Series Manual No. 701-055M
Before You Start Assembly Instructions for
4210ST & 4410ST Series Trekers
When you see this symbol, the subsequent
instructions and warnings are serious - follow
! On page 6 is a detailed listing of parts included in this kit.
without exception. Your life and the lives of
Use this list as a checklist to inventory parts received.
others depend on it!
These optional assembly instructions cont
ページ2に含まれる内容の要旨
Land Pride Assembly Instructions for 4210ST & 4410ST Series Trekers Refer to Figure 2A: • Do not press rocker switch into dump mounting panel until after electric lift cylinder has been installed and 2. Locate behind the dashboard a green wire with red after correct wiring connections have been verified in connector, green wire with yellow stripe and red “Final Assembly” on page 5 step 3. connector and black wire with blue connector. Wires can be located by looking through the left front fender
ページ3に含まれる内容の要旨
Land Pride Assembly Instructions for 4210ST & 4410ST Series Trekers Refer to Figure 6A: Electric Bed Lift 3. Remove the two extension springs from the Bed Electrical End Latch Assembly. 4. Remove attaching hardware mounting the Bed Latch 1/2" Clevis Pin Assembly. Attaching hardware consist of eight 1/4"-20 x 5/8" hex head cap screws, flat washers, hex flange lock nuts and four latch keeper bars. Extension Attaching Bed Latch Spring Hardware Assembly 5/32" Cotter Pin 23646 Electric Lift Lower Mou
ページ4に含まれる内容の要旨
Land Pride Assembly Instructions for 4210ST & 4410ST Series Trekers Refer to Figure 11A: Bed Latch Lock-Up Arm Removal 4. Do not connect rod end to cargo box until after Refer to Figure 12A: step 5. Extend the rod end of the electric lift until it is 1. With a standard screwdriver, pry the torsion spring approximately 1" from its connection point located off of the Bed Latch Lock-Up Arm. under the cargo box. Refer to Figure 10A: 5. With a secure hold on the cargo box, un-hook the Bed Latch Lock-
ページ5に含まれる内容の要旨
Land Pride Assembly Instructions for 4210ST & 4410ST Series Trekers Final Assembly Refer to Figure 3A on page 2: 3. Correctly orient rocker switch as shown in Figure 3A on page 2 and activate it to raise and lower cargo box. Pushing at the top of the rocker switch should raise the cargo box and at the bottom of the rocker switch should lower the cargo box. Switch the two green wires if the switch does not operate correctly. Refer to Figure 14A: 4. Once the rocker switch operates correctly, press
ページ6に含まれる内容の要旨
Land Pride Assembly Instructions for 4210ST & 4410ST Series Trekers Listing of Parts (4200ST & 4400ST Trekers) Your kit includes: 701-071A Electric Bed Lift for Treker ST Series Qty. Part No. Part Description 1 701-055M MANUAL ELECTRIC BED LIFT INSTRUCTION 2 805-045C PIN COTTER 5/32 X 1 1/4 LG 2 805-303C PIN CLEVIS 1/2X1 49/64 USABLE 1 833-254C DUMP SWITCH 1 833-271C SWITCH ACTUATOR 1 833-317C ELECT. LINEAR ACTUATOR 12" STROKE Manual No. 701-055M 8/15/05 6
ページ7に含まれる内容の要旨
Land Pride Assembly Instructions for 4200/4400 ST & NT (S/N 418339+) Refer to Figure 2B: Assembly Instructions for 3. Unbolt and remove bed latch lock-down from the 4200/4400 ST & NT (S/N 418339+) driver’s side of chassis. On page 10 is a detailed listing of parts included in this kit. Use this list as a checklist to inventory parts received. Tools required: • Standard Blade Screwdriver • Needle Nose Pliers • Work Gloves Initial Preparations 1. Park vehicle on a flat surface, move gear shift lev
ページ8に含まれる内容の要旨
Land Pride Assembly Instructions for 4200/4400 ST & NT (S/N 418339+) • Green wire with red connectorlabeled Dump Up to rocker switch bottom terminal. Green Wire With Dump Mounting Red Connector • Do not press rocker switch in to dump mounting panel Panel Opening until after electric lift cylinder has been installed and after correct wiring connections have been verified in Green Wire With “Final Assembly” on page 9 step 3. Yellow Stripe and Black Wire With Electric Lift Cylinder Installation Blu
ページ9に含まれる内容の要旨
Land Pride Assembly Instructions for 4200/4400 ST & NT (S/N 418339+) Refer to Figure 7B: Electric Lift 3. The Electric Bed Lift mounts in the same pin Connector connections as the Bed Latch Lock-Up Arm was mounted. First mount the electrical end of the Electric Bed Lift to the Treker frame with a 1/2" x 49/ 64" clevis pin. Secure pin with 5/32" cotter pin. The opposite end will be attached to the cargo box later. Final Assembly Refer to Figure 8B: 1. Locate T-shaped connector on Electric Lift Wi
ページ10に含まれる内容の要旨
Land Pride Assembly Instructions for 4200/4400 ST & NT (S/N 418339+) Listing of Parts (Trekers with S/N 418339+) Your kit includes: 701-071A Electric Bed Lift for Treker ST Series Qty. Part No. Part Description 1 701-055M MANUAL ELECTRIC BED LIFT INSTRUCTION 2 805-045C PIN COTTER 5/32 X 1 1/4 LG 2 805-303C PIN CLEVIS 1/2X1 49/64 USABLE 1 833-254C DUMP SWITCH 1 833-271C SWITCH ACTUATOR 1 833-317C ELECT. LINEAR ACTUATOR 12" STROKE 701-072A Electric Bed Lift for Treker NT Series Qty. Part No. Part
ページ11に含まれる内容の要旨
Land Pride Assembly Instructions for ST & NT Trekers (S/N 418338-) Refer to Figure 2C: Assembly Instructions for 3. Unbolt and remove bed latch lock-down from the driver’s side of chassis. ST & NT Trekers (S/N 418338-) On page 15 is a detailed listing of parts included in this kit. Use this list as a checklist to inventory parts received. The pictures in this section are of an NT Series Treker unless stated otherwise. Battery location and main wiring harness will be in a slightly different locat
ページ12に含まれる内容の要旨
Land Pride Assembly Instructions for ST & NT Trekers (S/N 418338-) Refer to Figure 6C: 5. Located behind the dashboard is the electric lift Two-Prong Connector electrical connector which can be identified by its two Attached to Electric green wires and one black wire. If the connector Lift Wiring harness cannot be located, then remove the glove box by prying the glove box from the dashboard with a screwdriver at its rivet locations. Once the connector is located, pull it through the mounting pan
ページ13に含まれる内容の要旨
Land Pride Assembly Instructions for ST & NT Trekers (S/N 418338-) Electric Lift Cylinder Installation ! CAUTION! Securely support cargo box in the up position to prevent injury while exchanging lock-up arm with Electric Lift Cylinder. ! CAUTION! Care should be taken when removing the Bed Latch Lock- Up Arm to prevent injury. Avoid pinch points and make Electric Bed Lift certain the cargo box does not fall when changing from Bed Latch Lock-Up Arm to Electric Bed Lift Assembly. Refer to Figure 8C
ページ14に含まれる内容の要旨
Land Pride Assembly Instructions for ST & NT Trekers (S/N 418338-) Refer to Figure 11C: 5. Check rocker pad and make certain it is rotated as shown in Figure 12C. If not, pry rocker pad off rocker o NOTE: The pictures on this page are of an NT Series switch, rotate it 180 and press rocker pad back on. Treker. Battery location and main wiring harness will be in a slightly different location for the ST Series. 6. Press rocker switch into the dump mounting panel once it is oriented correctly. 2. Lo
ページ15に含まれる内容の要旨
Land Pride Assembly Instructions for ST & NT Trekers (S/N 418338-) Listing of Parts (Trekers with S/N 418338-) Your kit includes: 701-044A Electric Bed Lift for Treker ST Series Qty. Part No. Part Description 1 701-055M MANUAL ELECTRIC BED LIFT INSTRUCTION 4 800-182C CABLE TIE 5 1/2 LONG 1/8 WIDE 2 805-045C PIN COTTER 5/32 X 1 1/4 LG 2 805-303C PIN CLEVIS 1/2X1 49/64 USABLE 1 833-254C DUMP SWITCH 1 833-271CSWITCH ACTUATOR 1 833-317C ELECT. LINEAR ACTUATOR 12" STROKE 1 833-326C WIRING HARNESS ELE
ページ16に含まれる内容の要旨
Corporate Office: P.O. Box 5060 Salina, Kansas 67402-5060 USA www.landpride.com
